I.S. EN 1501-4:2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
REFUSE COLLECTION VEHICLES AND THEIR ASSOCIATED LIFTING DEVICES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 4: NOISE TEST CODE FOR REFUSE COLLECTION VEHICLES
Hardcopy , PDF
04-05-2023
English
01-01-2007
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Preparation of the RCV for measurements
4.1 Test environment
4.2 Choice of the RCV
4.3 Position of the RCV during measurement
5 Operating conditions (before and) during measurement
5.1 RCV conditions
5.2 Presetting the engine speed
5.3 Fan speed
5.4 Selection of operations
5.5 Chassis operation
5.6 Compaction system operation
5.7 Lifting, tilting and lowering of a container operation
5.8 Dumping of specified waste into the hopper
6 Noise measurement
6.1 General
6.2 Microphone positions
6.3 Measurement durations
6.4 Measurements
7 Determination of the averaged sound power level for a
combination of operating conditions
8 Uncertainties
8.1 Measurement uncertainties
8.2 Production uncertainties
9 Information to be reported
10 Declaration, labelling and information for use
Annex A (normative) Information to be reported
Annex B (normative) Microphone positions
Annex C (informative) Proposed classification of RCVs for noise
measurement purposes (Valid for rear/side/front loaded)
Annex ZA (informative) Relationship between this European Standard
and the Essential Requirements of EU Directive 98/37/EC,
amended by 98/79/EC
Annex ZB (informative) Relationship between this European Standard
and the Essential Requirements of EU Directive 2006/42/EC
Defines the method for measuring the noise emission, which is a significant hazard of refuse collection vehicles (RCVs).
| DocumentType |
Standard
|
| Pages |
21
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 1501-4 : 2007 | Identical |
| NEN EN 1501-4 : 2007 | Identical |
| DIN EN 1501-4:2008-01 | Identical |
| NBN EN 1501-4 : 2008 | Identical |
| BS EN 1501-4:2007 | Identical |
| SN EN 1501-4 : 2007 | Identical |
| UNI EN 1501-4 : 2008 | Identical |
| EN 1501-4:2007 | Identical |
| NS EN 1501-4 : 1ED 2007 | Identical |
| ONORM EN 1501-4 : 2008 | Identical |
| EN 1501-2:2005+A1:2009 | Refuse collection vehicles and associated lifting devices - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| EN 1501-1:2011+A1:2015 | Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles |
| EN 840-1:2012 | Mobile waste and recycling containers - Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices - Dimensions and design |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| EN 1452-2 : 1999 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: PIPES |
| ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.