I.S. EN 14276-1:2006
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS
Available format(s)
Hardcopy , PDF
Superseded date
17-03-2020
Superseded by
Language(s)
English
Published date
01-01-2006
Publisher
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Materials
5 Pressure Vessel classification
6 Design
7 Manufacturing
8 Testing and inspection
Annex A (normative) - Alternative requirements for prevention
of brittle fracture: Method according to
temperature stress cases
Annex B (normative) - Specification and approval of brazing
procedures, brazers and brazing operators
Annex C (normative) - Pressure testing
Annex D (informative) - Relations between the different pressures
Annex E (normative) - Experimental methods
Annex F (normative) - Material characteristics for design
Annex G (informative) - Component classification in the sense of
the Pressure Equipment Directive (PED)
Annex H (informative) - Selection of module of conformity
Annex I (normative) - Grouping system for materials
Annex J (informative) - DN System
Annex K (normative) - Specification and approval of
expansion procedures and operators
Annex ZA (informative) - Relationship between this European
Standard and the Essential
Requirements of EU Directive 97/23/EC
Bibliography
Describes the requirements for material, design, manufacturing, testing and documentation for stationary pressure vessels intended for use in refrigerating systems and heat pumps.
| DevelopmentNote |
2006 Edition Re-issued in March 2011 & incorporates AMD 1 2011. (03/2011)
|
| DocumentType |
Standard
|
| Pages |
89
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 14276-1 : 2006 + A1 2011 | Identical |
| NBN EN 14276-1 : 2006 + A1 2011 | Identical |
| NEN EN 14276-1 : 2006 + A1 2011 | Identical |
| NS EN 14276-1 : 2006 + A1 2011 | Identical |
| SN EN 14276-1 : 2006 + A1 2011 | Identical |
| UNI EN 14276-1 : 2011 | Identical |
| UNE-EN 14276-1:2007 | Identical |
| BS EN 14276-1 : 2006 | Identical |
| EN 14276-1:2006+A1:2011 | Identical |
| DIN EN 14276-1:2011-05 | Identical |
| ONORM EN 14276-1 : 2011 | Identical |
| ISO 17672:2016 | Brazing — Filler metals |
| EN 10269:2013 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
| ISO 2553:2013 | Welding and allied processes Symbolic representation on drawings Welded joints |
| EN ISO 5817:2014 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2014) |
| EN 1045:1997 | Brazing - Fluxes for brazing - Classification and technical delivery conditions |
| EN 1515-1:1999 | Flanges and their joints - Bolting - Part 1: Selection of bolting |
| EN 13445-5 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 5: INSPECTION AND TESTING |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| EN 13445-6 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON |
| EN 378-4:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 4: Operation, maintenance, repair and recovery |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| CR 13445-7:2002 | Unfired pressure vessels - Part 7: Guidance on the use of the conformity procedures |
| EN ISO 17672:2016 | Brazing - Filler metals (ISO 17672:2016) |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) |
| EN 378-1:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 1: Basic requirements, definitions, classification and selection criteria |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EN 378-3:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 3: Installation site and personal protection |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| EN 10111:2008 | Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions |
| EN 764-1:2015+A1:2016 | Pressure equipment - Part 1: Vocabulary |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| EN 1005-2:2003+A1:2008 | Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery |
| EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
| EN 10216-2:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties |
| EN 764-5:2014 | Pressure equipment - Part 5: Inspection documentation of metallic materials and compliance with the material specification |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| EN 910 : 1996 | DESTRUCTIVE TESTS ON WELDS IN METALLIC MATERIALS - BEND TESTS |
| EN 13445-8 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 8: ADDITIONAL REQUIREMENTS FOR PRESSURE VESSELS OF ALUMINIUM AND ALUMINIUM ALLOYS |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| ISO 15614-8:2016 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 8: Welding of tubes to tube-plate joints |
| ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure |
| EN 1173:2008 | Copper and copper alloys - Material condition designation |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
| EN ISO 3677:2016 | Filler metal for soldering and brazing - Designation (ISO 3677:2016) |
| EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| ISO 7438:2016 | Metallic materials Bend test |
| EN 13445-4 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 4: FABRICATION |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience |
| ISO 3677:2016 | Filler metal for soldering and brazing — Designation |
| EN 22553:1994 | Welded, brazed and soldered joints - Symbolic representation on drawings (ISO 2553:1992) |
| ISO 857-1:1998 | Welding and allied processes Vocabulary Part 1: Metal welding processes |
| EN 12735-1:2016 | Copper and copper alloys - Seamless, round tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems |
| ISO 5187:1985 | Welding and allied processes — Assemblies made with soft solders and brazing filler metals — Mechanical test methods |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 10012:2003 | Measurement management systems — Requirements for measurement processes and measuring equipment |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN 10130:2006 | Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions |
| ISO 15609-2:2001 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 2: Gas welding |
| EN 764-2:2012 | Pressure equipment - Part 2: Quantities, symbols and units |
| EN 12517-1:2006 | Non-destructive testing of welds - Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography - Acceptance levels |
| EN ISO 10012:2003 | Measurement management systems - Requirements for measurement processes and measuring equipment (ISO 10012:2003) |
| ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
| ISO 817:2014 | Refrigerants Designation and safety classification |
| EN ISO 15614-8:2016 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 8: Welding of tubes to tube-plate joints (ISO 15614-8:2016) |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| EN 1418:1997 | Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| EN 764-3:2002 | Pressure equipment - Part 3: Definition of parties involved |
| EN 378-2:2016 | Refrigerating systems and heat pumps - Safety and environmental requirements - Part 2: Design, construction, testing, marking and documentation |
| EN 764-4:2014 | Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials |
| EN 12451:2012 | Copper and copper alloys - Seamless, round tubes for heat exchangers |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
| EN ISO 7438:2016 | Metallic materials - Bend test (ISO 7438:2016) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.