I.S. EN 14044:2014
Current
The latest, up-to-date edition.
HIGH RISE AERIAL APPLIANCES FOR FIRE AND RESCUE SERVICE USE - TURNTABLE LADDERS WITH SEQUENTIAL MOVEMENTS - SAFETY AND PERFORMANCE REQUIREMENTS AND TEST METHODS
Hardcopy , PDF
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 List of significant hazards
5 Requirements
6 Designation
7 Information for use
Annex A (informative) - Example of table reporting the
stability tests
Annex B (normative) - Operating time
Annex C (informative) - List of nominal reaches in several
European countries applicable to turntable ladders
Annex D (informative) - Verification and reception tests
Annex ZA (informative) - Relationship between this
European Standard and the Essential Requirements
of EU Directive 2006/42/EC
Bibliography
Describes the safety and performance requirements and test methods applicable to turntable ladders with sequential movements of classes 18, 24, 30 and > 30 to 56, as defined in 3.13, under the control of fire-fighters and intended for fire fighting and rescuing people.
| DocumentType |
Standard
|
| Pages |
94
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| UNI EN 14044 : 2014 | Identical |
| UNE-EN 14044:2007 | Identical |
| NEN EN 14044 : 2014 | Identical |
| NF EN 14044 : 2014 | Identical |
| BS EN 14044:2014 | Identical |
| DIN EN 14044:2014-04 | Identical |
| EN 14044:2014 | Identical |
| SN EN 14044 : 2014 | Identical |
| NBN EN 14044 : 2014 | Identical |
| NS EN 14044 : 2014 | Identical |
| CISPR 12:2007+AMD1:2009 CSV | Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers |
| EN 1846-2:2009+A1:2013 | Firefighting and rescue service vehicles - Part 2: Common requirements - Safety and performance |
| ISO 4302:2016 | Cranes — Wind load assessment |
| EN 61000-6-3:2007/A1:2011/AC:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010) |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| EN 60300-1:2014 | Dependability management - Part 1: Guidance for management and application |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN ISO 7731:2008 | Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003) |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 7731:2003 | Ergonomics Danger signals for public and work areas Auditory danger signals |
| IEC 61000-6-3:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments |
| EN 14043:2014 | High rise aerial appliances for fire and rescue service use - Turntable ladders with combined movements - Safety and performance requirements and test methods |
| MIL-HDBK-217 Revision F:1991 | RELIABILITY PREDICTION OF ELECTRONIC EQUIPMENT |
| EN 61000-6-2:2005/corrigendum:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60300-1:2014 | Dependability management - Part 1: Guidance for management and application |
| EN 1846-3:2013 | Firefighting and rescue service vehicles - Part 3: Permanently installed equipment - Safety and performance |
| IEC 60300-2:2004 | Dependability management - Part 2: Guidelines for dependability management |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| CEN/TS 15989:2015 | Firefighting and rescue service vehicles and equipment - Graphical symbols for control elements and displays and for markings |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN 1846-1:2011 | Firefighting and rescue service vehicles - Part 1: Nomenclature and designation |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 55012:2007/A1:2009 | VEHICLES, BOATS AND INTERNAL COMBUSTION ENGINES - RADIO DISTURBANCE CHARACTERISTICS - LIMITS AND METHODS OF MEASUREMENT FOR THE PROTECTION OF OFF-BOARD RECEIVERS |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| EN 1777:2010 | Hydraulic platforms (HPs) for fire fighting and rescue services - Safety requirements and testing |
| EN 60300-2:2004 | Dependability management - Part 2: Guidelines for dependability management |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.