I.S. EN 13941:2009
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
DESIGN AND INSTALLATION OF PREINSULATED BONDED PIPE SYSTEMS FOR DISTRICT HEATING
Hardcopy , PDF
21-07-2010
English
09-09-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, units and symbols
4 General considerations for system design
5 Components and materials
6 Actions and limit states
7 Installation
Annex A (normative) - Design of piping components under
internal pressure
Annex B (informative) - Geotechnics and pipe-soil interaction
Annex C (informative) - Global- and cross sectional analysis
Annex D (informative) - Calculation of heat losses
Annex E (informative) - National A-deviations
Bibliography
Describes rules for design, calculation and installation for preinsulated bonded pipe systems for buried hot water distribution and transmission networks with pipe assemblies in accordance with EN 253, for continuous operation with hot water at various temperatures up to 120 degrees C and occasionally with peak temperatures up to 140 degrees C and maximum internal pressure 25 bar (overpressure).
| DevelopmentNote |
2009 Edition Re-Issued in July 2010 & incorporates AMD 1 2010. (07/2010)
|
| DocumentType |
Standard
|
| Pages |
127
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| Supersedes |
| Standards | Relationship |
| EN 13941:2009+A1:2010 | Identical |
| NF EN 13941 : 2009 + A1 2010 | Identical |
| NS EN 13941 : 2009 + A1 2010 | Identical |
| NEN EN 13941 : 2009 + A1 2010 | Identical |
| UNI EN 13941 : 2011 | Identical |
| NBN EN 13941 : 2009 + A1 2010 | Identical |
| SN EN 13941 : 2009 + A1 2010 | Identical |
| BS EN 13941 : 2009 | Identical |
| DIN EN 13941:2010-12 | Identical |
| DIN EN 13941:2003-10 | Identical |
| ISO 3834-1:2005 | Quality requirements for fusion welding of metallic materials Part 1: Criteria for the selection of the appropriate level of quality requirements |
| EN 444:1994 | Non-destructive testing - General principles for radiographic examination of metallic materials by X- and gamma-rays |
| EN ISO 3834-3:2005 | Quality requirements for fusion welding of metallic materials - Part 3: Standard quality requirements (ISO 3834-3:2005) |
| ENV 1991-3:1995/AC:1998 | EUROCODE 1 - BASIS OF DESIGN AND ACTIONS ON STRUCTURES - TRAFFIC LOADS ON BRIDGES |
| EN ISO 3834-2:2005 | Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements (ISO 3834-2:2005) |
| ASME B31.1 : 2016 | POWER PIPING |
| EN 488:2015 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| ISO 3834-4:2005 | Quality requirements for fusion welding of metallic materials Part 4: Elementary quality requirements |
| EN ISO 3834-4:2005 | Quality requirements for fusion welding of metallic materials - Part 4: Elementary quality requirements (ISO 3834-4:2005) |
| ISO/TR 15608:2017 | Welding — Guidelines for a metallic materials grouping system |
| EN 1594:2013 | Gas infrastructure - Pipelines for maximum operating pressure over 16 bar - Functional requirements |
| ISO 14731:2006 | Welding coordination Tasks and responsibilities |
| EN 10216-2:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties |
| EN 448:2015 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| EN 13480-3:2017 | Metallic industrial piping - Part 3: Design and calculation |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| ISO 3834-2:2005 | Quality requirements for fusion welding of metallic materials Part 2: Comprehensive quality requirements |
| EN 1289:1998/A2:2003 | NON-DESTRUCTIVE TESTING OF WELDS - PENETRANT TESTING OF WELDS - ACCEPTANCE LEVELS |
| EN 489:2009 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN ISO 14731:2006 | Welding coordination - Tasks and responsibilities (ISO 14731:2006) |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| CEN/TR 1295-2:2005 | Structural design of buried pipelines under various conditions of loading - Part 2: Summary of nationally established methods of design |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN ISO 3834-1:2005 | Quality requirements for fusion welding of metallic materials - Part 1: Criteria for the selection of the appropriate level of quality requirements (ISO 3834-1:2005) |
| EN 1712:1997/A2:2004 | NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING OF WELDED JOINTS - ACCEPTANCE LEVELS |
| ISO 3419:1981 | Non-alloy and alloy steel butt-welding fittings |
| EN 13018:2016 | Non-destructive testing - Visual testing - General principles |
| ISO 9692-2:1998 | Welding and allied processes — Joint preparation — Part 2: Submerged arc welding of steels |
| EN 1291:1998/A2:2003 | NON-DESTRUCTIVE TESTING OF WELDS - MAGNETIC PARTICLE TESTING OF WELDS - ACCEPTANCE LEVELS |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
| EN 253:2009+A2:2015 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene |
| EN 1418:1997 | Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials |
| EN 970:1997 | Non-destructive examination of fusion welds - Visual examination |
| EN 1290:1998/A2:2003 | NON-DESTRUCTIVE EXAMINATION OF WELDS - MAGNETIC PARTICLE EXAMINATION OF WELDS |
| ISO 3834-3:2005 | Quality requirements for fusion welding of metallic materials Part 3: Standard quality requirements |
| EN 25817 : 1992 | ARC WELDED JOINTS IN STEEL - GUIDANCE ON QUALITY LEVELS FOR IMPERFECTIONS |
| EN 10253-2:2007 | Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.