I.S. EN 13924:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BITUMEN AND BITUMINOUS BINDERS - SPECIFICATIONS FOR HARD PAVING GRADE BITUMENS
Hardcopy , PDF
20-12-2015
English
01-01-2006
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Sampling
4 Requirements and test methods
5 Evaluation of conformity
Annex A (normative) - Calculation of the penetration index
Annex B (informative) - Informative properties
Annex ZA (informative) - Clauses of this European Standard
addressing the provisions of the EU Construction
Products Directive
Bibliography
Provides a framework for specifying the properties and relevant test methods for hard paving grade bitumens which are suitable for use in the construction and maintenance of roads, airfields and other paved areas.
| DevelopmentNote |
COR 2006 issued on 05-08-2011. (08/2011)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NS EN 13924 : 2006 AC 2007 | Identical |
| UNI EN 13924 : 2006 | Identical |
| UNE-EN 13924:2006 | Identical |
| BS EN 13924:2006 | Identical |
| NF EN 13924 : 2006 | Identical |
| NEN EN 13924 : 2006 C1 2006 | Identical |
| NBN EN 13924 : 2006 COR 2006 | Identical |
| DIN EN 13924:2006-07 | Identical |
| S.R. 28:2009 | RECOMMENDATION FOR THE USE AND IMPLEMENTATION OF THE I.S. EN 13108 SERIES BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS |
| EN 12592:2014 | Bitumen and bituminous binders - Determination of solubility |
| EN 1426:2015 | Bitumen and bituminous binders - Determination of needle penetration |
| ISO 2719:2016 | Determination of flash point — Pensky-Martens closed cup method |
| EN 12697-12:2008 | Bituminous mixtures - Test methods for hot mix asphalt - Part 12: Determination of the water sensitivity of bituminous specimens |
| EN 12697-1 : 2012 COR 2012 | BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 1: SOLUBLE BINDER CONTENT |
| EN 12596:2014 | Bitumen and bituminous binders - Determination of dynamic viscosity by vacuum capillary |
| EN 12697-11:2012 | Bituminous mixtures - Test methods for hot mix asphalt - Part 11: Determination of the affinity between aggregate and bitumen |
| EN 1427:2015 | Bitumen and bituminous binders - Determination of the softening point - Ring and Ball method |
| EN 14770:2012 | Bitumen and bituminous binders - Determination of complex shear modulus and phase angle - Dynamic Shear Rheometer (DSR) |
| EN 12597:2014 | Bitumen and bituminous binders - Terminology |
| EN 12697-26:2012 | Bituminous mixtures - Test methods for hot mix asphalt - Part 26: Stiffness |
| EN 58:2012 | Bitumen and bituminous binders - Sampling bituminous binders |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 4259:2006 | Petroleum products Determination and application of precision data in relation to methods of test |
| EN 12594:2014 | Bitumen and bituminous binders - Preparation of test samples |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 12607-3:2014 | Bitumen and bituminous binders - Determination of the resistance to hardening under influence of heat and air - Part 3: RFT method |
| EN ISO 2719:2016 | Determination of flash point - Pensky-Martens closed cup method (ISO 2719:2016) |
| EN 12607-1:2014 | Bitumen and bituminous binders - Determination of the resistance to hardening under influence of heat and air - Part 1: RTFOT method |
| EN 12593:2015 | Bitumen and bituminous binders - Determination of the Fraass breaking point |
| EN ISO 2592:2017 | Petroleum and related products - Determination of flash and fire points - Cleveland open cup method (ISO 2592:2017) |
| EN 12591:2009 | Bitumen and bituminous binders - Specifications for paving grade bitumens |
| EN 14771:2012 | Bitumen and bituminous binders - Determination of the flexural creep stiffness - Bending Beam Rheometer (BBR) |
| EN ISO 4259:2006 | Petroleum products - Determination and application of precision data in relation to methods of test (ISO 4259:2006) |
| EN 12595:2014 | Bitumen and bituminous binders - Determination of kinematic viscosity |
| CEN/TR 15352:2006 | Bitumen and bituminous binders - Development of performance-related specifications: status report 2005 |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.