I.S. EN 13481-2:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
RAILWAY APPLICATIONS - TRACK - PERFORMANCE REQUIREMENTS FOR FASTENING SYSTEMS - PART 2: FASTENING SYSTEMS FOR CONCRETE SLEEPERS
Hardcopy , PDF
04-03-2023
English
29-05-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Requirements
6 Test specimens
7 Fitness for purpose
8 Marking, labelling and packaging
Annex A (informative) - Vibration and noise
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2008/57/EC
Bibliography
Pertains to fastening systems in Categories A-E as specified in EN 13481-1:2012, 3.1, for use on concrete sleepers in ballasted track with maximum axle loads, and minimum curve radii.
| DevelopmentNote |
2012 Edition Re-Issued in February 2017 & incorporates AMD 1 2017. (03/2017)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NS EN 13481-2 : 2012 + A1 2017 | Identical |
| EN 13481-2:2012+A1:2017 | Identical |
| NF EN 13481-2 : 2012 + A1 2017 | Identical |
| NEN EN 13481-2 : 2012 + A1 2017 | Identical |
| NBN EN 13481-2 : 2012 COR 2014 | Identical |
| UNI EN 13481-2 : 2012 | Identical |
| DIN EN 13481-2:2012-08 | Identical |
| SN EN 13481-2+A1:2017 | Identical |
| BS EN 13481-2 : 2012 | Identical |
| UNE-EN 13481-2:2012 | Identical |
| ONORM EN 13481-2 : 2017 | Identical |
| EN 13146-6:2012 | Railway applications - Track - Test methods for fastening systems - Part 6: Effect of severe environmental conditions |
| EN 13146-3:2012 | Railway applications - Track - Test methods for fastening systems - Part 3: Determination of attenuation of impact loads |
| EN 13674-4:2006+A1:2009 | Railway applications - Track - Rail - Part 4: Vignole railway rails from 27 kg/m to, but excluding 46 kg/m |
| EN 15461:2008+A1:2010 | Railway applications - Noise emission - Characterisation of the dynamic properties of track sections for pass by noise measurements |
| EN 50122-2:2010 | RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRICAL SAFETY, EARTHING AND THE RETURN CIRCUIT - PART 2: PROVISIONS AGAINST THE EFFECTS OF STRAY CURRENTS CAUSED BY D.C. TRACTION SYSTEMS |
| EN 13146-7:2012 | Railway applications - Track - Test methods for fastening systems - Part 7: Determination of clamping force |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 13146-9:2009+A1:2011 | Railway applications - Track - Test methods for fastening systems - Part 9: Determination of stiffness |
| EN 13230-1:2016 | Railway applications - Track - Concrete sleepers and bearers - Part 1: General requirements |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 13146-1:2012+A1:2014 | Railway applications - Track - Test methods for fastening systems - Part 1: Determination of longitudinal rail restraint |
| EN 13674-1:2011+A1:2017 | Railway applications - Track - Rail - Part 1: Vignole railway rails 46 kg/m and above |
| EN 13481-1:2012 | Railway applications - Track - Performance requirements for fastening systems - Part 1: Definitions |
| EN 13146-10:2017 | Railway applications - Track - Test methods for fastening systems - Part 10: Proof load test for pull-out resistance |
| EN 13146-2:2012 | Railway applications - Track - Test methods for fastening systems - Part 2: Determination of torsional resistance |
| EN 13146-4:2012+A1:2014 | Railway applications - Track - Test methods for fastening systems - Part 4: Effect of repeated loading |
| EN 13146-8:2012 | Railway applications - Track - Test methods for fastening systems - Part 8: In service testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.