I.S. EN 13443-1:2002
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
WATER CONDITIONING EQUIPMENT INSIDE BUILDINGS - MECHANICAL FILTERS - PART 1: PARTICLE RATING 80 MICROMETER TO 150 MICROMETER - REQUIREMENTS FOR PERFORMANCES, SAFETY AND TESTING
Hardcopy , PDF
12-10-2007
English
07-02-2003
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Materials (Chemical and hygienic behaviour of materials)
6 General design requirements
7 Performances requirements
8 Performance tests
9 Technical documents, labelling and marking
Annex A (informative) Bibliographical information
Annex B (normative) Installation, operation and maintenance
Bibliography
Defines requirements relating to the construction and mode of operation of filters and describes relevant methods of testing.
| DevelopmentNote |
2002 Edition Re-Issued in October 2007 & incorporates AMD 1 2007. (10/2007)
|
| DocumentType |
Standard
|
| Pages |
28
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| Standards | Relationship |
| UNE-EN 13443-1:2003 | Identical |
| NEN EN 13443-1 : 2003 + A1 2007 | Identical |
| NF EN 13443-1 : 2003 + A1 2007 | Identical |
| BS EN 13443-1:2002 | Identical |
| NBN EN 13443-1 : 2003 + A1 2007 | Identical |
| UNI EN 13443-1 : 2007 | Identical |
| EN 13443-1:2002+A1:2007 | Identical |
| DIN EN 13443-1:2007-12 | Identical |
| NS EN 13443-1 : 2002 + A1 2007 | Identical |
| SN EN 13443-1 : 2002 + A1 2007 | Identical |
| ISO 9276-1:1998 | Representation of results of particle size analysis — Part 1: Graphical representation |
| EN 1254-1:1998 | Copper and copper alloys - Plumbing fittings - Part 1: Fittings with ends for capillary soldering or capillary brazing to copper tubes |
| EN 13443-2:2005+A1:2007 | Water conditioning equipment inside buildings - Mechanical filters - Part 2: Particle rating 1 µm to less than 80 µm - Requirements for performance, safety and testing |
| EN 1254-2:1998 | Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes |
| ISO 7005-3:1988 | Metallic flanges Part 3: Copper alloy and composite flanges |
| EN 15161:2006 | Water conditioning equipment inside buildings - Installation, operation, maintenance and repair |
| EN 1567:1999 | Building valves - Water pressure reducing valves and combination water pressure reducing valves - Requirements and tests |
| EN 1717:2000 | Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow |
| ISO 2591-1:1988 | Test sieving — Part 1: Methods using test sieves of woven wire cloth and perforated metal plate |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN 1333:2006 | Flanges and their joints - Pipework components - Definition and selection of PN |
| ISO 6509:1981 | Corrosion of metals and alloys Determination of dezincification resistance of brass |
| ISO 3822-3:1997 | Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 3: Mounting and operating conditions for in-line valves and appliances |
| EN ISO 6509:1995 | Corrosion of metals and alloys - Determination of dezincification resistance of brass (ISO 6509:1981) |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| ISO 13320-1:1999 | Particle size analysis Laser diffraction methods Part 1: General principles |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.