I.S. EN 13361:2018
Current
Current
The latest, up-to-date edition.
GEOSYNTHETIC BARRIERS - CHARACTERISTICS REQUIRED FOR USE IN THE CONSTRUCTION OF RESERVOIRS AND DAMS
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-01-2018
Publisher
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 Characteristics and corresponding methods of test
5 Assessment and verification of constancy of
performance (AVCP)
Annex A (normative) - Durability of geosynthetic
barriers
Annex ZA (informative) - Relationship of this European
Standard with Regulation (EU) No. 305/2011
Bibliography
Describes the relevant characteristics of geosynthetic barriers, including polymeric geosynthetic barriers, clay geosynthetic barriers and bituminous geosynthetic barriers, to be used as fluid barriers for potable, fresh or saline water, in the construction of reservoirs and dams, and the appropriate test methods to determine these characteristics.
| DocumentType |
Greenline
|
| Pages |
66
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN 13361 : 2013 | Identical |
| UNE-EN 13361:2013 | Identical |
| EN 13361:2018 | Identical |
| DIN EN 13361:2016-08 (Draft) | Identical |
| ONORM EN 13361 : 2013 | Identical |
| BS EN 13361:2013 | Identical |
| UNI EN 13361 : 2013 | Identical |
| NBN EN 13361 : 2013 | Identical |
| EN 13265:2016 | Geotextiles and geotextile-related products - Characteristics required for use in liquid waste containment projects |
| EN 14576:2005 | Geosynthetics - Test method for determining the resistance of polymeric geosynthetic barriers to environmental stress cracking |
| EN 14575:2005 | Geosynthetic barriers - Screening test method for determining the resistance to oxidation |
| EN 12226:2012 | Geosynthetics - General tests for evaluation following durability testing |
| EN ISO 1183-3:1999 | Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method (ISO 1183-3:1999) |
| EN 14150:2006 | Geosynthetic barriers - Determination of permeability to liquids |
| ISO 13438:2004 | Geotextiles and geotextile-related products Screening test method for determining the resistance to oxidation |
| EN ISO 10319:2015 | Geosynthetics - Wide-width tensile test (ISO 10319:2015) |
| ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| CEN/TS 14418:2014 | Geosynthetic Barriers - Test method for the determination of the influence of freezing-thawing cycles on the permeability of clay geosynthetic barriers |
| ASTM D 6141 : 2014-07 | GUIDE FOR SCREENING CLAY PORTION AND INDEX FLUX OF GEOSYNTHETIC CLAY LINER (GCL) FOR CHEMICAL COMPATIBILITY TO LIQUIDS |
| EN 13251:2016 | Geotextiles and geotextile-related products - Characteristics required for use in earthworks, foundations and retaining structures |
| EN 13249:2016 | Geotextiles and geotextile-related products - Characteristics required for use in the construction of roads and other trafficked areas (excluding railways and asphalt inclusion) |
| ISO 12236:2006 | Geosynthetics — Static puncture test (CBR test) |
| EN 1849-2:2009 | Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Part 2: Plastic and rubber sheets |
| EN ISO 527-4:1997 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997) |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| EN 495-5:2013 | Flexible sheets for waterproofing - Determination of foldability at low temperature - Part 5: Plastic and rubber sheets for roof waterproofing |
| ISO 9863-1:2016 | Geosynthetics Determination of thickness at specified pressures Part 1: Single layers |
| EN 14151:2010 | Geosynthetics - Determination of burst strength |
| EN 13253:2016 | Geotextiles and geotextile-related products - Characteristics required for use in erosion control works (coastal protection, bank revetments) |
| ISO 10319:2015 | Geosynthetics — Wide-width tensile test |
| EN 13250:2016 | Geotextiles and geotextile-related products - Characteristics required for use in the construction of railways |
| EN 12224:2000 | Geotextiles and geotextile-related products - Determination of the resistance to weathering |
| EN 12311-2:2013 | Flexible sheets for waterproofing - Determination of tensile properties - Part 2: Plastic and rubber sheets for roof waterproofing |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| EN 13255:2016 | Geotextiles and geotextile-related products - Characteristics required for use in the construction of canals |
| EN 13254:2016 | Geotextiles and geotextile-related products - Characteristics required for the use in the construction of reservoirs and dams |
| EN 12311-1:1999 | Flexible sheets for waterproofing - Part 1: Bitumen sheets for roof waterproofing - Determination of tensile properties |
| EN 12310-1:1999 | Flexible sheets for waterproofing - Part 1: Bitumen sheets for waterproofing - Determination of resistance to tearing (nail shank) |
| EN 14414:2004 | Geosynthetics - Screening test method for determining chemical resistance for landfill applications |
| ISO 12957-1:2005 | Geosynthetics Determination of friction characteristics Part 1: Direct shear test |
| EN 16416:2013 | Geosynthetic clay barriers - Determination of water flux index - Flexible wall permeameter method at constant head |
| EN 1109:2013 | Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of flexibility at low temperature |
| CEN/TS 14417:2014 | Geosynthetic barriers - Test method for the determination of the influence of wetting-drying cycles on the permeability of clay geosynthetic barriers |
| EN ISO 10318-1:2015 | Geosynthetics - Part 1: Terms and definitions (ISO 10318-1:2015) |
| EN ISO 1133-1:2011 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011) |
| ASTM D 696 : 2016 : REDLINE | Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer |
| EN ISO 12957-2:2005 | Geosynthetics - Determination of friction characteristics - Part 2: Inclined plane test (ISO 12957-2:2005) |
| ISO 12957-2:2005 | Geosynthetics — Determination of friction characteristics — Part 2: Inclined plane test |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| EN 12225:2000 | Geotextiles and geotextile-related products - Method for determining the microbiological resistance by a soil burial test |
| EN 14196:2016 | Geosynthetics - Test methods for measuring mass per unit area of clay geosynthetic barriers |
| EN 1296:2000 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roofing - Method of artificial ageing by long term exposure to elevated temperature |
| ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
| ISO 1183-3:1999 | Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method |
| ASTM D 7409 : 2015 : REDLINE | Standard Test Method for Carboxyl End Group Content of Polyethylene Terephthalate (PET) Yarns |
| EN ISO 9864:2005 | Geosynthetics - Test method for the determination of mass per unit area of geotextiles and geotextile-related products (ISO 9864:2005) |
| EN ISO 9863-1:2016 | Geosynthetics - Determination of thickness at specified pressures - Part 1: Single layers (ISO 9863-1:2016) |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 3696:1987 | Water for analytical laboratory use — Specification and test methods |
| EN 13256:2016 | Geotextiles and geotextile-related products - Characteristics required for use in the construction of tunnels and underground structures |
| EN ISO 3696:1995 | Water for analytical laboratory use - Specification and test methods (ISO 3696:1987) |
| EN 1849-1:1999 | Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Part 1: Bitumen sheets for roof waterproofing |
| EN ISO 12236:2006 | Geosynthetics - Static puncture test (CBR test) (ISO 12236:2006) |
| EN 13257:2016 | Geotextiles and geotextile-related products - Characteristics required for use in solid waste disposals |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| EN 13252:2016 | Geotextiles and geotextile-related products - Characteristics required for use in drainage systems |
| ISO 9864:2005 | Geosynthetics — Test method for the determination of mass per unit area of geotextiles and geotextile-related products |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| CEN/TS 14416:2014 | Geosynthetic barriers - Test method for determining the resistance to roots |
| EN 14415:2004 | Geosynthetic barriers - Test method for determining the resistance to leaching |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| EN ISO 1183-2:2004 | Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method (ISO 1183-2:2004) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.