Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

I.S. EN 13244-1:2002

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - GENERAL

Available format(s)

Hardcopy , PDF

Superseded date

14-09-2011

Superseded by

I.S. EN 12201-1:2011

Language(s)

English

Published date

01-01-2002

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

$67.50
Including GST where applicable

Foreword
Introduction
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
  3.1 Terms and definitions
      3.1.1 Geometrical definitions
      3.1.2 Definitions related to service conditions
      3.1.3 Definitions related to material
            characteristics
  3.2 Symbols
  3.3 Abbreviations
4 Material
  4.1 Compound
  4.2 Colour
      4.2.1 General
      4.2.2 Black compound
  4.3 Use of reprocessable and recyclable material
  4.4 Physical characteristics of the compound
  4.5 Fusion compatibility
  4.6 Classification and designation
Annex A (informative) Pressure reduction coefficients
Bibliography

Provides the general aspects of polyethylene (PE) piping systems intended for buried and above-ground pressure systems for water for general purposes, drainage and sewerage.

DocumentType
Standard
Pages
18
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

Standards Relationship
NF EN 13244-1 : 2003 Identical
SN EN 13244-1 : 2003 Identical
BS EN 13244-1:2002 Identical
NEN EN 13244-1 : 2003 Identical
NS EN 13244-1 : 1ED 2002 Identical
UNI EN 13244-1 : 2004 Identical
EN 13244-1:2002 Identical
NBN EN 13244-1 : 2003 Identical
DIN EN 13244-1:2003-04 Identical

EN ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009)
ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
EN 12118:1997 Plastics piping systems - Determination of moisture content in thermoplastics by coulometry
EN 728:1997 Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
ISO 6964:1986 Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification
ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
ISO 3:1973 Preferred numbers Series of preferred numbers
ISO 18553:2002 Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds
EN ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478:2007)
EN ISO 13479:2009 Polyolefin pipes for the conveyance of fluids - Determination of resistance to crack propagation - Test method for slow crack growth on notched pipes (ISO 13479:2009)
ISO 11414:2009 Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
ISO 1183:1987 Plastics Methods for determining the density and relative density of non-cellular plastics
ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
ISO 472:2013 Plastics — Vocabulary
EN 1056 : 1996 METHODS OF TESTING PLASTICS - THERMOPLASTICS PIPES, FITTINGS AND VALVES - PLASTICS PIPING AND DUCTING SYSTEMS - PLASTICS PIPES AND FITTINGS - METHOD FOR EXPOSURE TO DIRECT (NATURAL) WEATHERING
ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
ISO 13761:2017 Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 degrees C
EN ISO 1133:2005 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005)
ISO 760:1978 Determination of water Karl Fischer method (General method)
EN 12107 : 1997 PLASTICS PIPING SYSTEM - INJECTION MOULDED THERMOPLASTICS FITTINGS, VALVES AND ANCILLARY EQUIPMENT - DETERMINATION OF THE LONG-TERM HYDROSTATIC STRENGTH OF THERMOPLASTICS MATERIALS FOR INJECTION MOULDING OF PIPING COMPONENTS
ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
ISO/TR 9080:1992 Thermoplastics pipes for the transport of fluids — Methods of extrapolation of hydrostatic stress rupture data to determine the long-term hydrostatic strength of thermoplastics pipe materials
EN 12099:1997 Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content
EN 13244-2:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more