I.S. EN 12591:2009
Current
The latest, up-to-date edition.
BITUMEN AND BITUMINOUS BINDERS - SPECIFICATIONS FOR PAVING GRADE BITUMENS
Hardcopy , PDF
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Sampling
5 Requirements and test methods
6 Evaluation of conformity
Annex A (normative) - Calculation of the penetration
index, I[p]
Annex B (informative) - Complementary information on grade
selection
Annex ZA (informative) - Clauses of this European Standard
addressing the provisions of the EU Construction
Products Directive
Bibliography
Gives a framework for specifying a range of properties and relevant test methods for bitumens, which are suitable for use in the construction and maintenance of roads, airfields and other paved areas, together with requirements for evaluation of conformity.
| DocumentType |
Standard
|
| Pages |
31
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN 12591 : 2009 | Identical |
| NEN EN 12591 : 2009 | Identical |
| BS EN 12591:2009 | Identical |
| EN 12591:2009 | Identical |
| SN EN 12591 : 2009 | Identical |
| NS EN 12591 : 2009 + NA 2011 | Identical |
| NBN EN 12591 : 2009 | Identical |
| UNI EN 12591 : 2009 | Identical |
| UNE-EN 12591:2009 | Identical |
| DIN EN 12591:2009-08 | Identical |
| S.R. 28:2009 | RECOMMENDATION FOR THE USE AND IMPLEMENTATION OF THE I.S. EN 13108 SERIES BITUMINOUS MIXTURES - MATERIAL SPECIFICATIONS |
| EN 12592:2014 | Bitumen and bituminous binders - Determination of solubility |
| EN 1426:2015 | Bitumen and bituminous binders - Determination of needle penetration |
| ISO 2719:2016 | Determination of flash point — Pensky-Martens closed cup method |
| EN 12697-12:2008 | Bituminous mixtures - Test methods for hot mix asphalt - Part 12: Determination of the water sensitivity of bituminous specimens |
| EN 12697-1 : 2012 COR 2012 | BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 1: SOLUBLE BINDER CONTENT |
| PREN 15322 : DRAFT 2011 | BITUMEN AND BITUMINOUS BINDERS - FRAMEWORK FOR SPECIFYING CUT-BACK AND FLUXED BITUMINOUS BINDERS |
| EN 13108-5:2016 | Bituminous mixtures - Material specifications - Part 5: Stone Mastic Asphalt |
| EN 12596:2014 | Bitumen and bituminous binders - Determination of dynamic viscosity by vacuum capillary |
| EN 12697-11:2012 | Bituminous mixtures - Test methods for hot mix asphalt - Part 11: Determination of the affinity between aggregate and bitumen |
| EN 1427:2015 | Bitumen and bituminous binders - Determination of the softening point - Ring and Ball method |
| EN 15326:2007+A1:2009 | Bitumen and bituminous binders - Measurement of density and specific gravity - Capillary-stoppered pyknometer method |
| EN 13808:2013 | Bitumen and bituminous binders - Framework for specifying cationic bituminous emulsions |
| EN 12597:2014 | Bitumen and bituminous binders - Terminology |
| EN 12697-26:2012 | Bituminous mixtures - Test methods for hot mix asphalt - Part 26: Stiffness |
| EN 13304:2009 | Bitumen and bituminous binders - Framework for specification of oxidised bitumens |
| EN 13108-1:2016 | Bituminous mixtures - Material specifications - Part 1: Asphalt Concrete |
| EN 12607-2:2014 | Bitumen and bituminous binders - Determination of the resistance to hardening under influence of heat and air - Part 2: TFOT method |
| EN 13108-7:2016 | Bituminous mixtures - Material specifications - Part 7: Porous Asphalt |
| EN 58:2012 | Bitumen and bituminous binders - Sampling bituminous binders |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 13108-3:2016 | Bituminous mixtures - Material specifications - Part 3: Soft Asphalt |
| EN 13305:2009 | Bitumen and bituminous binders - Framework for specification of hard industrial bitumens |
| ISO 4259:2006 | Petroleum products Determination and application of precision data in relation to methods of test |
| EN 12594:2014 | Bitumen and bituminous binders - Preparation of test samples |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 2719:2016 | Determination of flash point - Pensky-Martens closed cup method (ISO 2719:2016) |
| EN 13108-6:2016 | Bituminous mixtures - Material specifications - Part 6: Mastic Asphalt |
| EN 12607-1:2014 | Bitumen and bituminous binders - Determination of the resistance to hardening under influence of heat and air - Part 1: RTFOT method |
| EN 14023:2010 | Bitumen and bituminous binders - Specification framework for polymer modified bitumens |
| EN 12593:2015 | Bitumen and bituminous binders - Determination of the Fraass breaking point |
| EN ISO 2592:2017 | Petroleum and related products - Determination of flash and fire points - Cleveland open cup method (ISO 2592:2017) |
| EN 13108-2:2016 | Bituminous mixtures - Material specifications - Part 2: Asphalt Concrete for Very Thin Layers (BBTM) |
| EN ISO 4259:2006 | Petroleum products - Determination and application of precision data in relation to methods of test (ISO 4259:2006) |
| EN 12595:2014 | Bitumen and bituminous binders - Determination of kinematic viscosity |
| CEN/TR 15352:2006 | Bitumen and bituminous binders - Development of performance-related specifications: status report 2005 |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.