I.S. EN 1254-6:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS
Hardcopy , PDF
29-06-2021
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Testing, assessment and sampling methods
6 Evaluation of conformity
7 Classification and designation
8 Marking
9 Documentation
Annex A (normative) - Method for testing leaktightness
of joints under internal hydrostatic pressure
Annex B (normative) - Method for testing resistance to
pull-out of joints with metallic tube
Annex C (normative) - Test method for resistance of
joints with metallic tube to temperature cycling
Annex D (normative) - Method for testing the resistance
of joints with metallic tube to pressure cycling
Annex E (normative) - Test method for leaktightness of
joints with metallic tube under vacuum
Annex F (normative) - Test method for the resistance
of joints with metallic tube to vibration
Annex G (normative) - Test method for leaktightness of
joints with metallic tube under internal hydrostatic
pressure while subjected to bending
Annex H (normative) - Test method for disconnection
and re-use
Annex I (normative) - Fitting rotation test
Annex J (normative) - Determination of resistance to
stress corrosion
Annex K (normative) - Pressure test for fittings bodies
with as-cast microstructure or fabricated by welding
or brazing
Annex L (normative) - Determination of mean depth of
dezincification
Bibliography
Defines materials and test requirements for fittings of copper and copper alloys.
| Committee |
TC 133
|
| DocumentType |
Standard
|
| Pages |
51
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 1254-6:2012 | Identical |
| EN 1655:1997 | Copper and copper alloys - Declarations of conformity |
| EN 12293:1999 | Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling |
| EN ISO 15874-5:2013 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO 15874-5:2013) |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| EN ISO 15876-2:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes (ISO 15876-2:2017) |
| ISO 15875-5:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 5: Fitness for purpose of the system |
| ISO 15875-2:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes |
| EN ISO 15876-5:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2017) |
| ISO 21003-5:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 5: Fitness for purpose of the system |
| EN 12449:2016 | Copper and copper alloys - Seamless, round tubes for general purposes |
| ISO 15874-2:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 2: Pipes |
| ISO 22391-2:2009 | Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 2: Pipes |
| EN 713:1993 | Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending |
| EN ISO 15875-5:2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system (ISO 15875-5:2003) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 21003-2:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes |
| ISO 6509:1981 | Corrosion of metals and alloys Determination of dezincification resistance of brass |
| ISO 15876-2:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 12164:2016 | Copper and copper alloys - Rod for free machining purposes |
| EN 12295:1999 | Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling |
| ISO 9924-1:2016 | Rubber and rubber products — Determination of the composition of vulcanizates and uncured compounds by thermogravimetry — Part 1: Butadiene, ethylene-propylene copolymer and terpolymer, isobutene-isoprene, isoprene and styrene-butadiene rubbers |
| EN ISO 22391-2:2009 | Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 2: Pipes (ISO 22391-2:2009) |
| EN ISO 21003-5:2008 | Multilayer piping systems for hot and cold water installations inside buildings - Part 5: Fitness for purpose of the system (ISO 21003-5:2008) |
| EN 12294:1999 | Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum |
| EN ISO 15874-2:2013 | Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2013) |
| EN ISO 6509:1995 | Corrosion of metals and alloys - Determination of dezincification resistance of brass (ISO 6509:1981) |
| EN 12165:2016 | Copper and copper alloys - Wrought and unwrought forging stock |
| ISO 15874-5:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 5: Fitness for purpose of the system |
| ISO 15876-5:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 5: Fitness for purpose of the system |
| EN 1982:2017 | Copper and copper alloys - Ingots and castings |
| ISO 6957:1988 | Copper alloys Ammonia test for stress corrosion resistance |
| EN 712:1993 | Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.