I.S. EN 12516-1:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 1: TABULATION METHOD FOR STEEL VALVE SHELLS
Hardcopy , PDF
21-01-2020
26-11-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and units
5 Material groups and material temperature limitations
6 Pressure/temperature (p/t) ratings
7 Temperature effects
8 Dimensions
9 Auxiliary connections
10 End dimensions
11 Marking
Annex A (normative) Methods used for establishing pressure/temperature ratings
Annex B (normative) Material groups
Annex C (informative) Special Class
Annex D (informative) Radiographic procedure and acceptance standards
Annex E (informative) Magnetic particle examination procedure and acceptance standards
Annex F (informative) Liquid penetrant examination procedure and acceptance standards
Annex G (informative) Ultrasonic examination procedure and acceptance standards
Annex H (informative) Requirement for Limited Class valves in sizes DN 65 and smaller
Annex I (informative) ASTM/ASME material
Annex J (informative) Relationship between DN, NPS, pipe inside diameter Dni, pipe outside diameter OD
Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC (Pressure Equipment Directive)
Bibliography
This European Standard specifies the tabulation method for determining the wall thickness of valve bodies, bonnets and covers with essentially circular cross-section made in forged, cast or fabricated steel.
| Committee |
TC 69
|
| DocumentType |
Standard
|
| Pages |
206
|
| ProductNote |
NOTE: The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document. THIS STANDARD ALSO REFERS TO EN 10213:2007,ASME Section II
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNI EN 12516-1 : 2014 | Identical |
| DIN EN 12516-1:2015-01 | Identical |
| NBN EN 12516-1 : 2014 | Identical |
| NEN EN 12516-1 : 2014 | Identical |
| NF EN 12516-1 : 2014 | Identical |
| BS EN 12516-1 : 2014 | Identical |
| EN 12516-1:2014 | Identical |
| ONORM EN 12516-1 : 2014 | Identical |
| UNE-EN 12516-1:2016 | Identical |
| NS EN 12516-1 : 2014 | Identical |
| SN EN 12516-1 : 2015 | Identical |
| EN ISO 9692-1:2013 | Welding and allied processes - Types of joint preparation - Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels (ISO 9692-1:2013) |
| EN 10228-3:1998 | Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings |
| ASTM E 446 : 2015 : REDLINE | Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness |
| EN 10028-7:2000 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| ASTM E 186 : 2015 : REDLINE | Standard Reference Radiographs for Heavy-Walled (2 to 4<fraction><num>1</num><den>2</den></fraction > in. (50.8 to 114 mm)) Steel Castings |
| EN 10222-2:1999 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperature properties |
| EN 10213:2007+A1:2016 | Steel castings for pressure purposes |
| ASTM E 446 : 2014 | Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| EN 19:2002 | Industrial valves - Marking of metallic valves |
| ASTM E 280 : 2010 | Standard Reference Radiographs for Heavy-Walled (4<span class='unicode'>½</span> to 12-in. (114 to 305-mm)) Steel Castings |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| EN 12680-1:2003 | Founding - Ultrasonic examination - Part 1: Steel castings for general purposes |
| EN 10222-3:1998 | Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties |
| EN 12516-4:2014 | Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 736-2:2016 | Valves - Terminology - Part 2: Definition of components of valves |
| ISO 5579:2013 | Non-destructive testing — Radiographic testing of metallic materials using film and X- or gamma rays — Basic rules |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| EN 10228-1:1999 | Non-destructive testing of steel forgings - Part 1: Magnetic particle inspection |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| EN ISO 9934-1:2016 | Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2016) |
| ISO 9692-1:2013 | Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| EN 10028-3:2003 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| EN 10028-2:2003 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| EN ISO 5579:2013 | Non-destructive testing - Radiographic testing of metallic materials using film and X- or gamma rays - Basic rules (ISO 5579:2013) |
| ASME B16.5 : 2013 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| EN 10222-3:2017 | Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties |
| EN 10222-5:2017 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
| EN 10228-3:2016 | Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings |
| EN 736-2:1997 | Valves - Terminology - Part 2: Definition of components of valves |
| EN 10028-4:2003 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties |
| ISO 4200:1991 | Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length |
| EN 10222-4:2017 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
| ISO 9934-1:2016 | Non-destructive testing — Magnetic particle testing — Part 1: General principles |
| ASME B16.34 : 2013 | VALVES - FLANGED, THREADED, AND WELDING END |
| EN 10222-2:2017 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
| EN 1369:2012 | Founding - Magnetic particle testing |
| EN 462-1:1994 | Non-destructive testing - Image quality of radiographs - Part 1: Image quality indicators (wire type) - Determination of image quality value |
| ASTM E 280 : 2015 : REDLINE | Standard Reference Radiographs for Heavy-Walled (4<fraction><num>1</num><den>2</den></fraction > to 12 in. (114 to 305 mm)) Steel Castings |
| EN 12681:2003 | Founding - Radiographic examination |
| ASTM E 186 : 2010 | Standard Reference Radiographs for Heavy-Walled (2 to 4<span class='unicode'>½</span>-in. (50.8 to 114-mm)) Steel Castings |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| EN 12516-2:2014 | Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
| EN 10222-5:1999 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
| EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
| EN 10028-4:2017 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties |
| EN 19:2016 | Industrial valves - Marking of metallic valves |
| EN 10222-4:1998 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
| EN 736-3:2008 | Valves - Terminology - Part 3: Definition of terms |
| EN ISO 9934-1:2001 | Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2001) |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.