I.S. EN 12449:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
COPPER AND COPPER ALLOYS - SEAMLESS, ROUND TUBES FOR GENERAL PURPOSES
Hardcopy , PDF
19-12-2023
English
01-01-2016
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Designations
5 Ordering information
6 Requirements
7 Sampling
8 Test methods
9 Declaration of conformity and
inspection documentation
10 Marking, packaging, labelling
Bibliography
Defines the composition, property requirements and tolerances on dimensions and form for seamless round drawn copper and copper alloy tubes for general purposes supplied in the size range from 3 mm up to and including 450 mm outside diameter and from 0,3 mm up to and including 20 mm wall thickness.
| DocumentType |
Standard
|
| Pages |
46
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNE-EN 12449:2016 | Identical |
| NEN EN 12449 : 2016 | Identical |
| SN EN 12449:2016 | Identical |
| UNI EN 12449 : 2012 | Identical |
| BS EN 12449:2016 | Identical |
| ONORM EN 12449 : 2016 | Identical |
| DIN EN 12449:2015-11 (Draft) | Identical |
| EN 12449:2016 | Identical |
| NBN EN 12449 : 2016 | Identical |
| NF EN 12449 : 2016 | Identical |
| NS EN 12449 : 2016 | Identical |
| DIN EN 12449:1999-10 | Identical |
| EN 12168:2016 | Copper and copper alloys - Hollow rod for free machining purposes |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| EN 1655:1997 | Copper and copper alloys - Declarations of conformity |
| EN 1971-2:2011 | Copper and copper alloys - Eddy current test for measuring defects on seamless round copper and copper alloy tubes - Part 2: Test with an internal probe on the inner surface |
| EN ISO 6506-1:2014 | Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014) |
| EN ISO 8493:2004 | Metallic materials - Tube - Drift-expanding test (ISO 8493:1998) |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| EN 1412:2016 | Copper and copper alloys - European numbering system |
| ISO 1190-1:1982 | Copper and copper alloys — Code of designation — Part 1: Designation of materials |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| ISO 2624:1990 | Copper and copper alloys — Estimation of average grain size |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| EN 16090:2011 | Copper and copper alloys - Estimation of average grain size by ultrasound |
| ISO 1811-2:1988 | Copper and copper alloys — Selection and preparation of samples for chemical analysis — Part 2: Sampling of wrought products and castings |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ISO 8493:1998 | Metallic materials Tube Drift-expanding test |
| EN 1976:2012 | Copper and copper alloys - Cast unwrought copper products |
| EN 1971-1:2011 | Copper and copper alloys - Eddy current test for measuring defects on seamless round copper and copper alloy tubes - Part 1: Test with an encircling test coil on the outer surface |
| EN 1173:2008 | Copper and copper alloys - Material condition designation |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN ISO 2624:1995 | Copper and copper alloys - Estimation of average grain size (ISO 2624:1990) |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 196:1978 | Wrought copper and copper alloys — Detection of residual stress — Mercury(I) nitrate test |
| ISO 6957:1988 | Copper alloys Ammonia test for stress corrosion resistance |
| EN ISO 196:1995 | Wrought copper and copper alloys - Detection of residual stress - Mercury(I) nitrate test (ISO 196:1978) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.