ENV 28041 : DRAFT 1993
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
HUMAN RESPONSE TO VIBRATION - MEASURING INSTRUMENTATION
12-01-2013
01-04-2005
Foreword
Introduction to the European Prestandard
1. Scope
2. Normative references
3. Definitions
4. Characteristics
5. Frequency - weighting and amplifier characteristics
6. Detector and indicator characteristics
7. Sensitivity to various environments
8. Calibration and verification of the basic characteristics
of the vibration - measuring instrumentation
9. Rating information and instruction manual
Annexes
A (informative) Additional information
B (informative) Analytical expressions corresponding to
tables 4 to 8
C (informative) Graphs correponding to tables 4 to 8
D (informative) Time weighting
Tables
1 Frequency ranges
2 Preferred reference calibration frequencies
3 Maximum change in reading withing 1 h of operation
4 Frequency weighting : whole body, severe discomfort,
z axis, 0,1 Hz to 1 Hz (motion sickness) based on ISO 2631-3
5 Frequency weighting : whole body, x axis and y axis, 1 Hz to
80 Hz, based on ISO 2631
6 Frequency weighting : whole body, z axis, 1 Hz to 80 Hz,
based on ISO 2631
7 Frequency weighting : whole body, combined, 1 Hz to 80 Hz,
based on ISO 2631
8 Frequency weighting : hand-arm, based on ISO 5349
9 Maximum error for r.m.s. detector - indicator system
10 Response to test signal bursts
11 Tolerances for linear integration
12 Tolerances on sensitivity linearity referred to the reference
Figures
1 Rectangular - pulse set
C.1 Frequency weighting (magnitude) for whole body, severe
discomfort. z axis, 0,1 Hz to 0,63 Hz (motion sickness) :
corresponds to table 4
C.2 Frequency weighting (magnitude) for whole body, x axis and
y axis, 1 Hz to 80 Hz: corresponds to table 5
C.3 Frequency weighting (magnitude) for whole body, z axis, 1 Hz
to 80 Hz: corresponds to table 6
C.4 Frequency weighting (magnitude) for whole body, combined,
1 Hz to 80 Hz: corresponds to table 7
C.5 Frequency weighting (magnitude) for hand/arm, 8 Hz to 1 000 Hz:
corresponds to table 8
D.1 Weighting curves for linear and exponential integration
National Annexes
National annex NA (informative) Committees responsible
National annex NB (informative) Cross references
Gives instrumentation for a method of measuring vibration in an given frequency range, given in ISO 2631-1 for assessing the vibration as perceived by human beings. Applicable to instrumentation for the measurement of hand-arm vibration and/or whole-body vibration. Specifies electrical, vibration and environmental tests to verify compliance with the characteristics specified and also determines the method for sensitivity calibration.
| Committee |
CEN/TC 231
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| Standards | Relationship |
| NEN NVN ENV ISO 8041 : 1997 AMD 1 2001 | Identical |
| DD ENV 28041:1993 | Identical |
| NEN NVN ENV 28041 : 1997 | Identical |
| NBN ENV 28041 : 96 AMD 1 2001 | Identical |
| NFE 90 403 : 93 AMD 1 2002 | Identical |
| DIN V ENV 28041 : 93 AMD 1 2001 | Identical |
| NEN NVN ISO 8041 : 1993 | Identical |
| I.S. EN 50144-1:1998 | SAFETY OF HAND-HELD ELECTRIC MOTOR OPERATED TOOLS - PART 1: GENERAL REQUIREMENTS |
| BS EN 12096:1997 | Mechanical vibration. Declaration and verification of vibration emission values |
| EN 12096:1997 | Mechanical vibration - Declaration and verification of vibration emission values |
| EN 1033 : 1995 | HAND-ARM VIBRATION - LABORATORY MEASUREMENT OF VIBRATION AT THE GRIP SURFACE OF HAND-GUIDED MACHINERY - GENERAL |
| EN ISO 5349-1:2001 | Mechanical vibration - Measurement and evaluation of human exposure to hand-transmitted vibration - Part 1: General requirements (ISO 5349-1:2001) |
| I.S. EN 30326-1:1994 | MECHANICAL VIBRATION - LABORATORY METHOD FOR EVALUATING VEHICLE SEAT VIBRATION - PART 1: BASIC REQUIREMENTS (ISO 10326-1:1992/AMD 2:2011) |
| BS EN 50144-1:1999 | Safety of hand-held electric motor operated tools General requirements |
| I.S. EN 50144-2-13:2002 | SAFETY OF HAND-HELD ELECTRIC MOTOR OPERATED TOOLS - PART 2-13: PARTICULAR REQUIREMENTS FOR CHAIN SAWS |
| I.S. TS 15694:2004 | MECHANICAL VIBRATION AND SHOCK - MEASUREMENT AND EVALUATION OF SINGLE SHOCKS TRANSMITTED FROM HAND-HELD AND HAND-GUIDED MACHINES TO THE HAND-ARM SYSTEM |
| ISO/TS 15694:2004 | Mechanical vibration and shock — Measurement and evaluation of single shocks transmitted from hand-held and hand-guided machines to the hand-arm system |
| I.S. EN ISO 5349-1:2002 | MECHANICAL VIBRATION - MEASUREMENT AND EVALUATION OF HUMAN EXPOSURE TO HAND-TRANSMITTED VIBRATION - PART 1: GENERAL REQUIREMENTS |
| BS EN 50260-1:2002 | Safety of hand-held battery-powered motor-operated tools and battery packs General requirements |
| DIN EN ISO 5349-1:2001-12 | MECHANICAL VIBRATIONS - MEASUREMENT AND EVALUATION OF HUMAN EXPOSURE TO HAND-TRANSMITTED VIBRATION - PART 1: GENERAL REQUIREMENTS |
| BS EN ISO 5349-1:2001 | Mechanical vibration. Measurement and evaluation of human exposure to hand-transmitted vibration General requirements |
| NFE 90 401-2 : 2001 | MECHANICAL VIBRATION AND SHOCK - EVALUATION OF HUMAN EXPOSURE TO WHOLE-BODY VIBRATION - PART 2: GENERAL REQUIREMENTS |
| 02/706469 DC : DRAFT MAY 2002 | PREN ISO 20643 - HAND-TRANSMITTED VIBRATION FROM HAND-HELD OR HAND-GUIDED MACHINERY - MEASUREMENT OF VIBRATION AT THE GRIP SURFACE |
| 07/30171078 DC : DRAFT AUG 2007 | BS EN 61029-1 - SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 1: GENERAL REQUIREMENTS |
| ANSI S3.40 : 2002 | |
| EN ISO/TS 15694 : 2004 | MECHANICAL VIBRATION AND SHOCK - MEASUREMENT AND EVALUATION OF SINGLE SHOCKS TRANSMITTED FROM HAND-HELD AND HAND-GUIDED MACHINES TO THE HAND-ARM SYSTEM |
| BS EN 50144-2-13:2002 | Safety of hand-held electric motor operated tools Particular requirements for chain saws |
| I.S. EN 50260-1:2002 | SAFETY OF HAND-HELD BATTER-POWERED MOTOR-OPERATED TOOLS AND BATTERY PACKS - PART 1: GENERAL REQUIREMENTS |
| BS EN 1033:1996 | Hand-arm vibration. Laboratory measurement of vibration at the grip surface of hand-guided machinery. General |
| EN 50260-1:2002 | Safety of hand-held battery-powered motor-operated tools and battery packs - Part 1: General requirements |
| EN 50144-2-13:2002 | Safety of hand-held electric motor operated tools - Part 2-13: Particular requirements for chain saws |
| EN 50144-1 : 98 COR 2005 | SAFETY OF HAND-HELD ELECTRIC MOTOR OPERATED TOOLS - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.