EN ISO 3506-1:2009
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009)
Superseded date
29-04-2020
Superseded by
Published date
15-11-2009
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Symbols
4 Designation, marking and finish
5 Chemical composition
6 Mechanical properties
7 Testing
Annex A (normative) - External thread - Calculation of
stress area
Annex B (informative) - Description of the groups and
grades of stainless steels
Annex C (informative) - Stainless steel composition
specifications
Annex D (informative) - Stainless steels for cold
heading and extruding
Annex E (informative) - Austenitic stainless steels
with particular resistance to
chloride induced stress
corrosion
Annex F (informative) - Mechanical properties at
elevated temperatures;
application at low
temperatures
Annex G (informative) - Time-temperature diagram of
intergranular corrosion in
austenitic stainless steels,
grade A2 (18/8 steels)
Annex H (informative) - Magnetic properties for
austenitic stainless steels
Bibliography
ISO 3506-1:2009 specifies the mechanical properties of bolts, screws and studs made of austenitic, martensitic and ferritic steel grades of corrosion-resistant stainless steels, when tested over an ambient temperature range of 10 °C to 35 °C. Properties vary at higher or lower temperatures.ISO 3506-1:2009 applies to bolts, screws and studs- with nominal thread diameter d ≤ 39 mm,- of triangular ISO metric threads with diameters and pitches in accordance with ISO 68-1, ISO 261 and ISO 262, and- of any shape.It does not apply to screws with special properties, such as weldability.
| Committee |
CEN/TC 185
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ONORM EN ISO 3506-1 : 2010 | Identical |
| NS EN ISO 3506-1 : 2009 | Identical |
| PN EN ISO 3506-1 : 2009 | Identical |
| NBN EN ISO 3506-1 : 2010 | Identical |
| UNI EN ISO 3506-1 : 2010 | Identical |
| BS EN ISO 3506-1:2009 | Identical |
| NF EN ISO 3506-1 : 2010 | Identical |
| UNE-EN ISO 3506-1:2010 | Identical |
| DIN EN ISO 3506-1:2010-04 | Identical |
| I.S. EN ISO 3506-1:2009 | Identical |
| SN EN ISO 3506-1 : 2010 | Identical |
| ISO 3506-1:2009 | Identical |
| NEN EN ISO 3506-1 : 2009 | Identical |
| EN 14423:2013+A1:2016 | Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 bar |
| 03/319820 DC : DRAFT DEC 2003 | EN 1515-3 - FLANGES AND THEIR JOINTS - BOLTING - PART 3: CLASSIFICATION OF BOLT MATERIALS FOR STEEL FLANGES, CLASS DESIGNATED |
| UNI EN 1090-3 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| CEI EN 50216-9 : 2010 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 9: OIL-TO-WATER HEAT EXCHANGERS |
| 14/30304786 DC : 0 | BS EN 15048-2 - NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE |
| 12/30254917 DC : DRAFT JAN 2012 | BS EN 877 - CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| BS EN 593:2017 | Industrial valves. Metallic butterfly valves for general purposes |
| BS EN 1090-5:2017 | Execution of steel structures and aluminium structures Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications |
| 10/30234610 DC : DRAFT NOV 2010 | BS EN 14420-3 - HOSE FITTINGS WITH CLAMP UNITS - PART 3: CLAMP UNITS, BOLTED OR PINNED |
| 04/30123995 DC : DRAFT OCT 2004 | EN 50216-10 - POWER TRANSFORMER AND REACTOR FITTINGS - PART 10: OIL-TO-AIR HEAT EXCHANGERS |
| DIN 16271:2004-07 | PN 250 and PN 400 valves with test connection for pressure gauges |
| BS EN 50216-10:2009 | Power transformer and reactor fittings Oil-to-air heat exchangers |
| DD ENV 1090-6:2001 | Execution of steel structures Supplementary rules for stainless steel |
| PREN 50119 : DRAFT 2017 | RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| I.S. EN 1515-4:2009 | FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| NF EN 50216-12 : 2011 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 12: FANS |
| 17/30360051 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| ONORM EN 1090-3 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| DIN EN 1090-3:2008-09 | EXECUTION OF STEEL AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL RULES FOR EXECUTION OF ALUMINIUM STRUCTURES |
| BS EN 1090-3:2008 | Execution of steel structures and aluminium structures Technical requirements for aluminium structures |
| EN 15048-1:2016 | Non-preloaded structural bolting assemblies - Part 1: General requirements |
| I.S. EN 13480-2:2017 | METALLIC INDUSTRIAL PIPING - PART 2: MATERIALS |
| I.S. EN ISO 3269:2000 | FASTENERS - ACCEPTANCE INSPECTION |
| BS EN 13480-2:2017 | Metallic industrial piping Materials |
| DIN EN 1759-1:2005-02 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| BS EN ISO 7089:2000 | Plain washers. Normal series. Product grade A |
| I.S. EN 14276-1:2006 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| BS EN 1662:1998 | Hexagon bolts with flange. Small series |
| BS EN 1993-1-4 : 2006 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-4: GENERAL RULES - SUPPLEMENTARY RULES FOR STAINLESS STEELS |
| BS EN 14420-3:2013 | Hose fittings with clamp units Clamp units, bolted or pinned |
| UNI EN 12516-2 : 2014 | INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 2: CALCULATION METHOD FOR STEEL VALVE SHELLS |
| DIN EN 1090-5:2017-07 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR COLD-FORMED STRUCTURAL ALUMINIUM ELEMENTS AND COLD-FORMED STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS |
| DIN EN ISO 16048:2003-06 | PASSIVATION OF CORROSION-RESISTANT STAINLESS-STEEL FASTENERS |
| DIN EN 1090-2:2011-10 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| I.S. EN 12284:2003 | REFRIGERATING SYSTEMS AND HEAT PUMPS - VALVES - REQUIREMENTS, TESTING AND MARKING |
| EN 12693:2008 | Refrigerating systems and heat pumps - Safety and environmental requirements - Positive displacement refrigerant compressors |
| PREN 1090-3 : DRAFT 2017 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| I.S. EN ISO 8735:1998 | PARALLEL PINS WITH INTERNAL THREAD, OF HARDENED STEEL OR MARTENSITIC STAINLESS STEEL |
| DIN EN 15001-1:2011-02 | Gas infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| UNE-EN 15048-1:2018 | Non-preloaded structural bolting assemblies - Part 1: General requirements |
| 16/30339483 DC : 0 | BS EN 593 - INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| 17/30341013 DC : DRAFT AUG 2017 | BS EN 50119 - RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| DIN EN 12693:2016-10 (Draft) | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| DIN 3015-2:1999-01 | Fastening clamps - Block clamps - Part 2: Heavy duty (S) |
| DIN 3015-1:1999-01 | Fastening clamps - Block clamps - Part 1: Light duty (L) |
| UNI EN 1515-4 : 2010 | FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| 11/30249108 DC : 0 | BS EN 12516-2 - INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 2: CALCULATION METHOD FOR STEEL VALVE SHELLS |
| PREN 1090-2 : DRAFT 2015 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| BS EN 12693:2008 | Refrigerating systems and heat pumps. Safety and environmental requirements. Positive displacement refrigerant compressors |
| I.S. EN 50216-9:2009 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 9: OIL-TO-WATER HEAT EXCHANGERS |
| DIN 18799-3:1999-08 | LADDERS FOR CONSTRUCTION WORKS - PART 3: LADDERS FOR CHIMNEYS - SAFETY REQUIREMENTS AND TESTS |
| DIN 3015-3:1999-01 | Fastening clamps - Block clamps - Part 3: Double clamps (Z) |
| NF EN 1515-4 : 2010 | FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| BS EN 13445-2 : 2014 | UNFIRED PRESSURE VESSELS - PART 2: MATERIALS |
| BS EN 1999-1-1 : 2007 | EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES |
| I.S. EN 15048-1:2016 | NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 1: GENERAL REQUIREMENTS |
| I.S. EN 14423:2013 | CLAMP TYPE COUPLING ASSEMBLIES FOR USE WITH STEAM HOSES RATED FOR PRESSURES UP TO 18 BAR |
| UNE-EN 15048-2:2017 | Non-preloaded structural bolting assemblies - Part 2: Fitness for purpose |
| I.S. EN 50216-10:2009 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 10: OIL-TO-AIR HEAT EXCHANGERS |
| I.S. EN 50216-12:2011 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 12: FANS |
| DIN EN 1090-2:2015-07 (Draft) | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| BS EN 1090-2 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| UNI EN 1090-2 : 2011 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| DIN EN 12284:2004-01 | Refrigerating systems and heat pumps - Valves - Requirements, testing and marking |
| UNE-EN 50216-12:2011 | Power transformer and reactor fittings - Part 12: Fans |
| UNE-EN 12516-2:2016 | Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
| BS EN ISO 8735:1998 | Parallel pins with internal thread, of hardened steel or martensitic stainless steel |
| BS EN 15048-1:2007 | Non-preloaded structural bolting assemblies General requirements |
| BS EN ISO 8733:1998 | Parallel pins with internal thread, of unhardened steel or austenitic stainless steel |
| BS EN 1665:1997 | Hexagon bolts with flange. Heavy series |
| I.S. EN 12516-2:2014 | INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 2: CALCULATION METHOD FOR STEEL VALVE SHELLS |
| I.S. EN 1993-1-4:2006 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-4: GENERAL RULES - SUPPLEMENTARY RULES FOR STAINLESS STEELS (INCLUDING IRISH NATIONAL ANNEX) |
| DIN EN 14420-3:2013-09 | HOSE FITTINGS WITH CLAMP UNITS - PART 3: CLAMP UNITS, BOLTED OR PINNED |
| DIN EN 13611:2019-06 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements |
| I.S. EN 15048-2:2016 | NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE |
| EN 50216-12:2011 | Power transformer and reactor fittings - Part 12: Fans |
| I.S. EN 14420-3:2013 | HOSE FITTINGS WITH CLAMP UNITS - PART 3: CLAMP UNITS, BOLTED OR PINNED |
| KTA 3507 : 2014(R2017) | FACTORY TESTS, POST-REPAIR TESTS AND CERTIFICATION OF SATISFACTORY PERFORMANCE IN SERVICE OF MODULES AND DEVICES FOR THE INSTRUMENTATION AND CONTROLS OF THE SAFETY SYSTEM |
| KTA 3702 : 2014(R2017) | EMERGENCY POWER GENERATING FACILITIES WITH DIESEL-GENERATOR UNITS IN NUCLEAR POWER PLANTS |
| DIN EN 1999-1-1:2014-03 | Eurocode 9: Design of aluminium structures - Part 1-1: General structural rules |
| I.S. EN 593:2017 | INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| UNI EN 12693 : 2008 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| I.S. EN 1999-1-1:2007 | EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES (INCLUDING IRISH NATIONAL ANNEX) |
| 05/30132920 DC : DRAFT APR 2005 | EN 1090-2 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR THE EXECUTION OF STEEL STRUCTURES |
| NF EN 15001-1 : 2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| UNE-EN 1090-2:2011 | Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures |
| I.S. EN 1090-3:2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| KTA 3211.1 : 2015 | PRESSURE AND ACTIVITY RETAINING COMPONENTS OF SYSTEMS OUTSIDE THE PRIMARY CIRCUIT - PART 1: MATERIALS |
| PREN 1090-4 : DRAFT 2014 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS |
| EN 1090-2:2008+A1:2011 | Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures |
| EN 1090-3:2008 | Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures |
| EN 12516-2:2014 | Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
| DIN EN 1993-1-4:2015-10 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-4: GENERAL RULES - SUPPLEMENTARY RULES FOR STAINLESS STEELS |
| DIN EN ISO 7093-1:2000-11 | PLAIN WASHERS - LARGE SERIES - PART 1: PRODUCT GRADE A |
| DIN EN ISO 4762:2004-06 | Hexagon socket head cap screws (ISO 4762:2004) |
| DIN EN 14276-1:2011-05 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| BS EN ISO 15983:2002 | Open end blind rivets with break pull mandrel and protruding head. A2/A2 |
| ISO 16585:2002 | Closed end blind rivets with pull mandrel and protruding head — A2/SSt |
| BS EN ISO 16585:2002 | Closed end blind rivets with pull mandrel and protruding head. A2/SSt |
| EN 14276-1:2020 | Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
| UNI EN 14276-1 : 2011 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| EN ISO 3269:2000 | FASTENERS - ACCEPTANCE INSPECTION |
| UNI EN 14219 : 2006 | HEXAGON BOLTS WITH FLANGE WITH METRIC FINE PITCH THREAD - SMALL SERIES |
| UNI EN 15001-1 : 2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| UNI EN 14420-3 : 2013 | HOSE FITTINGS WITH CLAMP UNITS - PART 3: CLAMP UNITS, BOLTED OR PINNED |
| DIN 16272:2004-07 | PN 250 and PN 400 valves with shut-off test connection for pressure gauges |
| I.S. EN 13445-2:2014 | UNFIRED PRESSURE VESSELS - PART 2: MATERIALS |
| BS EN 50216-9:2009 | Power transformer and reactor fittings Oil-to-water heat exchangers |
| I.S. EN ISO 8733:1998 | PARALLEL PINS WITH INTERNAL THREAD, OF UNHARDENED STEEL OR AUSTENITIC STAINLESS STEEL |
| UNI EN 1999-1-1 : 2014 | EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES |
| I.S. EN ISO 8745:1998 | GROOVED PINS - HALF-LENGTH TAPER GROOVED |
| 09/30188143 DC : DRAFT OCT 2009 | BS EN 13480-2:2002/A2 - METALLIC INDUSTRIAL PIPING - PART 2: MATERIALS |
| BS EN 1515-4:2009 | Flanges and their joints. Bolting Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| PREN 593 : DRAFT 2016 | INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| PREN 14592 : DRAFT 2017 | TIMBER STRUCTURES - DOWEL-TYPE FASTENERS - REQUIREMENTS |
| 10/30234634 DC : 0 | BS EN 14423 - CLAMP TYPE COUPLING ASSEMBLIES FOR USE WITH STEAM HOSES RATED FOR PRESSURES UP TO 18 BAR |
| 04/30123712 DC : DRAFT OCT 2004 | EN 15048-2 - NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: SUITABILITY TEST |
| 08/30173031 DC : DRAFT JAN 2008 | BS EN 1515-4 - FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| 04/30123986 DC : DRAFT OCT 2004 | EN 50216-9 - POWER TRANSFORMER AND REACTOR FITTINGS - PART 9: OIL TO WATER HEAT EXCHANGER |
| 04/30123693 DC : DRAFT OCT 2004 | EN 15048-1 - NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 1: GENERAL REQUIREMENTS |
| DIN 19207:2004-02 | Measurement of fluid flow by means of pressure differential devices - Threaded pipe end and accessories |
| DIN 16270:2004-07 | PN 250 and PN 400 valves without test connection for pressure gauges |
| PREN 15048-2 : DRAFT 2014 | NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE |
| I.S. EN 15001-1:2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| 14/30297831 DC : 0 | BS EN 1090-4 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 4: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED STEEL ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS |
| NF EN 1090-2 : 2009 + A1 2011 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| DIN EN 13611:2016-09 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| 17/30348949 DC : 0 | BS EN 1090-3 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| PREN 13611 : DRAFT 2017 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| UNE-EN 14423:2014 | Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 bar |
| I.S. EN 12693:2008 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| BS EN 13480-2:2017+A3:2018 | Metallic industrial piping Materials |
| DIN EN 15048-1:2016-09 | NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 1: GENERAL REQUIREMENTS |
| DIN EN 15048-2:2016-09 | NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE |
| BS EN 1515-3:2005 | Flanges and their joints. Bolting Classification of bolt materials for steel flanges, class designated |
| BS EN 12284:2003 | Refrigerating systems and heat pumps. Valves. Requirements, testing and marking |
| BS EN ISO 3269:2001 | Fasteners. Acceptance inspection |
| UNE-EN 15001-1:2010 | Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| ISO 8733:1997 | Parallel pins with internal thread, of unhardened steel and austenitic stainless steel |
| BS EN 14219:2003 | Hexagon bolts with flange with metric fine pitch thread. Small series |
| BS EN ISO 16048:2003 | Passivation of corrosion-resistant stainless-steel fasteners |
| BS EN 1515-2:2001 | Flanges and their joints. Bolting Classification of bolt materials for steel flanges, PN designated |
| BS EN 15048-2:2007 | Non-preloaded structural bolting assemblies Suitability test |
| UNE-EN 1515-4:2010 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| BS EN ISO 8745:1998 | Grooved pins. Half-length taper grooved |
| ISO 8745:1997 | Grooved pins Half-length taper grooved |
| EN 14276-1:2006+A1:2011 | Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
| EN 13480-2:2017 | Metallic industrial piping - Part 2: Materials |
| BS EN 14276-1 : 2006 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| ISO 8735:1997 | Parallel pins with internal thread, of hardened steel and martensitic stainless steel |
| BS EN 1759-1:2004 | Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, class-designated Steel flanges, NPS 1/2 to 24 |
| BS EN 1515-1:2000 | Flanges and their joints. Bolting Selection of bolting |
| ISO 16048:2003 | Passivation of corrosion-resistant stainless-steel fasteners |
| ISO 15983:2002 | Open end blind rivets with break pull mandrel and protruding head — A2/A2 |
| BS EN 12516-2:2014 | Industrial valves. Shell design strength Calculation method for steel valve shells |
| UNE-EN 14420-3:2014 | Hose fittings with clamp units - Part 3: Clamp units, bolted or pinned |
| EN 1515-4:2009 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| EN 50216-9:2009 | Power transformer and reactor fittings - Part 9: Oil-to-water heat exchangers |
| EN ISO 7089:2000 | Plain washers - Normal series - Product grade A (ISO 7089:2000) |
| EN 15001-1:2009 | Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| EN ISO 16585:2002 | Closed end blind rivets with pull mandrel and protruding head - A2/SSt (ISO 16585:2002) |
| EN ISO 8735:1997 | Parallel pins with internal thread, of hardened steel or martensitic stainless steel (ISO 8735:1997) |
| EN 1515-1:1999 | Flanges and their joints - Bolting - Part 1: Selection of bolting |
| EN ISO 16048:2003 | Passivation of corrosion-resistant stainless-steel fasteners (ISO 16048:2003) |
| EN ISO 15983:2002 | Open end blind rivets with break pull mandrel and protruding head - A2/A2 (ISO 15983:2002) |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| EN 1515-2:2001 | Flanges and their joints - Bolting - Part 2: Classification of bolt materials for steel flanges, PN designated |
| EN 15048-2:2016 | Non-preloaded structural bolting assemblies - Part 2: Fitness for purpose |
| EN ISO 7090:2000 | Plain washers, chamfered - Normal series - Product grade A (ISO 7090:2000) |
| EN ISO 8733:1997 | Parallel pins with internal thread, of unhardened steel or austenitic stainless steel (ISO 8733:1997) |
| EN ISO 7092:2000 | Plain washers - Small series - Product grade A (ISO 7092:2000) |
| EN ISO 7093-1:2000 | Plain washers - Large series - Part 1: Product grade A (ISO 7093-1:2000) |
| EN 1515-3:2005 | Flanges and their joints - Bolting - Part 3: Classification of bolt materials for steel flanges, class designated |
| EN ISO 15984:2002 | Open end blind rivets with break pull mandrel and countersunk head - A2/A2 (ISO 15984:2002) |
| EN ISO 8745:1997 | Grooved pins - Half-length taper grooved (ISO 8745:1997) |
| EN 593:2017 | Industrial valves - Metallic butterfly valves for general purposes |
| EN 14420-3:2013 | Hose fittings with clamp units - Part 3: Clamp units, bolted or pinned |
| 15/30320416 DC : 0 | BS EN 1090-2 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| 08/30187521 DC : 0 | BS EN 593 - INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES |
| BS EN 50216-12:2011 | Power transformer and reactor fittings Fans |
| PREN 14420-3 : DRAFT 2010 | HOSE FITTINGS WITH CLAMP UNITS - PART 3: CLAMP UNITS, BOLTED OR PINNED |
| 12/30257022 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - GENERAL REQUIREMENTS |
| UNE-EN 1993-1-4:2012 | Eurocode 3 - Design of steel structures - Part 1-4: General rules - Supplementary rules for stainless steels |
| BS EN 15001-1:2009 | Gas infrastructure. Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations Detailed functional requirements for design, materials, construction, inspection and testing |
| DIN EN 1515-4:2010-04 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| DIN 19558:2002-12 | WASTEWATER TREATMENT PLANTS - OUTLET INSTALLATIONS, WEIR AND SCUM BAFFLE, SUBMERGED EFFLUENT PIPES IN TANKS - CONSTRUCTION PRINCIPLES, MAIN DIMENSIONS, LAYOUT |
| DIN 3016-2:2000-06 | FASTENING CLAMPS - PART 2: WITH FASTENING LUGS |
| DIN EN 14219:2003-09 | HEXAGON BOLTS WITH FLANGE WITH METRIC FINE PITCH THREAD - SMALL SERIES |
| I.S. EN 1090-2:2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| KTA 3205.2 : 2015 COR 2016 | COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS - PART 2: COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS FOR PRESSURE AND ACTIVITY-RETAINING COMPONENTS IN SYSTEMS OUTSIDE THE PRIMARY CIRCUIT |
| I.S. EN 13611:2015 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| UNE-EN 13445-2:2015 | Unfired pressure vessels - Part 2: Materials |
| BS EN 13611:2015 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels. General requirements |
| UNE-EN 1090-3:2011 | Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures |
| I.S. EN 1090-5:2017 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR COLD-FORMED STRUCTURAL ALUMINIUM ELEMENTS AND COLD-FORMED STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS |
| UNE-EN 13611:2016 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements |
| UNE-EN 50216-10:2010 | Power transformer and reactor fittings - Part 10: Oil-to-air heat exchangers |
| CEI EN 50216-10 : 2010 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 10: OIL-TO-AIR HEAT EXCHANGERS |
| BS EN 14423:2013+A2:2019 | Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 bar |
| BS EN ISO 15984:2002 | Open end blind rivets with break pull mandrel and countersunk head. A2/A2 |
| ISO 15984:2002 | Open end blind rivets with break pull mandrel and countersunk head — A2/A2 |
| DIN EN 12693:2008-09 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| EN 1090-5:2017 | Execution of steel structures and aluminium structures - Part 5: Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications |
| EN 12284:2003 | Refrigerating systems and heat pumps - Valves - Requirements, testing and marking |
| I.S. EN 13611:2015/AC:2016 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| DIN EN 1515-3:2005-12 | Flanges and their joints - Bolting - Part 3: Classification of bolt materials for steel flanges, Class designated |
| EN 50216-10:2009 | Power transformer and reactor fittings - Part 10: Oil-to-air heat exchangers |
| UNE-EN 13480-2:2017 | Metallic industrial piping - Part 2: Materials (Endorsed by Asociación Española de Normalización in September of 2019.) |
| UNE-EN 14276-1:2007 | Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| ISO 683-13:1974 | Heat-treated steels, alloy steels and free-cutting steels Part 13: Wrought stainless steels |
| ISO 6508-1:2016 | Metallic materials — Rockwell hardness test — Part 1: Test method |
| ISO 724:1993 | ISO general-purpose metric screw threads — Basic dimensions |
| ISO 16426:2002 | Fasteners — Quality assurance system |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| ISO 68-1:1998 | ISO general purpose screw threads — Basic profile — Part 1: Metric screw threads |
| ISO 3651-2:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid |
| ISO 8044:2015 | Corrosion of metals and alloys Basic terms and definitions |
| ISO 16048:2003 | Passivation of corrosion-resistant stainless-steel fasteners |
| ISO 3651-1:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in nitric acid medium by measurement of loss in mass (Huey test) |
| ISO 261:1998 | ISO general purpose metric screw threads — General plan |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 4954:1993 | Steels for cold heading and cold extruding |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.