EN ISO 3269:2000
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fasteners - Acceptance inspection (ISO 3269:2000)
Published date
01-06-2000
Publisher
Superseded date
25-09-2019
Superseded by
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and conditions
4 General principles and requirements
5 Acceptance inspection procedure for fastener
characteristics
Annex A (informative) Recommendations for
acceptance-inspection procedures (for example,
for dimensional characteristics)
Annex B (informative) Guidance and explanation
concerning the principle of this International
Standard
Bibliography
Gives the procedure to be followed by the purchaser at his acceptance inspection so as to decide whether a lot of fasteners may be accepted or rejected, when another acceptance procedure has not been agreed.
| Committee |
CEN/TC 185
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 3269:2000 | Identical |
| BS EN ISO 3269:2001 | Identical |
| NEN EN ISO 3269 : 2000 | Identical |
| PN EN ISO 3269 : 2004 | Identical |
| NS EN ISO 3269 : 1ED 2000 | Identical |
| NF EN ISO 3269 : 2000 | Identical |
| SS-EN ISO 3269:2000 | Identical |
| NBN EN ISO 3269 : 2000 | Identical |
| DIN EN ISO 3269:2000-11 | Identical |
| I.S. EN ISO 3269:2000 | Identical |
| ONORM EN ISO 3269 : 2000 | Identical |
| UNE-EN ISO 3269:2000 | Identical |
| DIN EN 16983:2017-09 | DISC SPRINGS - QUALITY SPECIFICATIONS - DIMENSIONS |
| 02/704463 DC : DRAFT MAR 2002 | PREN 14399-4 - HIGH-STRENGTH STRUCTURAL BOLTING FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES |
| 02/704465 DC : DRAFT MAR 2002 | PREN 14399-6 - HIGH-STRENGTH STRUCTURAL BOLTING FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS FOR SYSTEMS HR AND HV |
| 13/30277440 DC : 0 | BS EN 14399-6 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| I.S. EN 1515-4:2009 | FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| PREN 14399-8 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| DIN EN 14399-10:2016-01 (Draft) | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| EN 14399-8:2007 | High-strength structural bolting assemblies for preloading - Part 8: System HV - Hexagon fit bolt and nut assemblies |
| ISO 4029:2003 | Hexagon socket set screws with cup point |
| BS EN ISO 4029:2003 | Hexagon socket set screws with cup point |
| BS EN ISO 15974:2001 | Closed and blind rivets with break pull mandrel and countersunk head. AIA/St |
| BS EN ISO 16426:2002 | Fasteners. Quality assurance system |
| BS EN ISO 15980:2002 | Open end blind rivets with break pull mandrel and countersunk head. St/St |
| BS EN 14218:2003 | Hexagon nuts with flange. Fine pitch thread |
| DIN EN ISO 4029:2004-05 | Hexagon socket set screws with cup point (ISO 4029:2003); German version EN ISO 4029:2003 |
| DIN EN 14399-8:2008-03 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| EN ISO 4029:2003 | Hexagon socket set screws with cup point (ISO 4029:2003) |
| 13/30277434 DC : 0 | BS EN 14399-4 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES |
| 07/30107797 DC : 0 | BS EN 14399-9 - HIGH STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - BOLT AND NUT ASSEMBLIES WITH DIRECT TENSION INDICATORS |
| 07/30166055 DC : 0 | BS EN 14399-10 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| PREN 14399-5 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| DIN EN 14399-8:2016-01 (Draft) | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| I.S. EN 14399-10:2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| PREN 14399-10 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| ONORM EN 14399-10 : JUN 2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| EN 14399-10:2018 | High-strength structural bolting assemblies for preloading - Part 10: System HRC - Bolt and nut assemblies with calibrated preload |
| BS EN ISO 15978:2002 | Open end blind rivets with break pull mandrel and countersunk head. AIA/St |
| BS EN ISO 15981:2002 | Open end blind rivets with break pull mandrel and protruding head. AIA/AIA |
| BS EN 14399-5 : 2015-02 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| ISO 15981:2002 | Open end blind rivets with break pull mandrel and protruding head — AIA/AIA |
| BS EN ISO 16583:2002 | Open end blind rivets with break pull mandrel and countersunk head. Cu/St or Cu/Br or Cu/SSt |
| BS EN ISO 15976:2002 | Closed end blind rivets with break pull mandrel and protruding head. St/St |
| I.S. EN 14399-3:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES |
| I.S. EN 14399-4:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES |
| I.S. EN 14399-6:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| I.S. EN 14399-5:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| DIN EN 14399-3:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES |
| DIN 7989-1:2001-04 | Washers for steel structures - Part 1: Product grade C |
| I.S. EN 16983:2016 | DISC SPRINGS - QUALITY SPECIFICATIONS - DIMENSIONS |
| BS EN 14399-8:2007 | High-strength structural bolting assemblies for preloading System HV. Hexagon fit bolt and nut assemblies |
| 13/30277437 DC : 0 | BS EN 14399-5 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| 13/30277431 DC : 0 | BS EN 14399-3 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES |
| PREN 14399-9 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| 02/704464 DC : DRAFT MAR 2002 | PREN 14399-5 - HIGH-STRENGTH STRUCTURAL BOLTING FOR PRELOADING - PART 5: PLAIN WASHERS FOR SYSTEM HR |
| 15/30332551 DC : 0 | BS EN 14399-10 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| PREN 14399-3 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES |
| PREN 14399-6 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| EN 14399-7:2007 | High-strength structural bolting assemblies for preloading - Part 7: System HR - Countersunk head bolt and nut assemblies |
| DIN EN 14399-7:2016-01 (Draft) | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES |
| DIN EN ISO 4762:2004-06 | Hexagon socket head cap screws (ISO 4762:2004); German version EN ISO 4762:2004 |
| BS EN ISO 15983:2002 | Open end blind rivets with break pull mandrel and protruding head. A2/A2 |
| ISO 16585:2002 | Closed end blind rivets with pull mandrel and protruding head — A2/SSt |
| BS EN ISO 16585:2002 | Closed end blind rivets with pull mandrel and protruding head. A2/SSt |
| BS EN ISO 15982:2002 | Open end blind rivets with break pull mandrel and countersunk head. AIA/AIA |
| EN ISO 15980:2002 | Open end blind rivets with break pull mandrel and countersunk head - St/St (ISO 15980:2002) |
| EN ISO 15973:2000 | Closed end blind rivets with break pull mandrel and protruding head - AIA/St (ISO 15973:2000) |
| 15/30332548 DC : 0 | BS EN 14399-8 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| DIN 7989-2:2001-04 | Washers for steel structures - Part 2: Product grade A |
| DIN 440:2001-03 | Washers with square hole for use in timber constructions |
| BS EN 1515-4:2009 | Flanges and their joints. Bolting Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| 08/30173031 DC : DRAFT JAN 2008 | BS EN 1515-4 - FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| DIN EN 14399-9:2016-01 (Draft) | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| BS EN 14399-7:2007 | High-strength structural bolting assemblies for preloading System HR. Countersunk head bolt and nut assemblies |
| BS EN 14399-10:2009 | High-strength structural bolting assemblies for preloading System HRC. Bolt and nut assemblies with calibrated preload |
| DIN EN ISO 6157-2:2004-10 | Fasteners - Surface discontinuities - Part 2: Nuts (ISO 6157-2:1995) |
| BS EN 14399-6:2005 | High-strength structural bolting assemblies for preloading Plain chamfered washers |
| BS EN 14399-3:2015 | High-strength structural bolting assemblies for preloading System HR. Hexagon bolt and nut assemblies |
| ISO 15982:2002 | Open end blind rivets with break pull mandrel and countersunk head — AIA/AIA |
| ISO 6157-2:1995 | Fasteners — Surface discontinuities — Part 2: Nuts |
| BS EN ISO 15973:2001 | Closed and blind rivets with break pull mandrel and protruding head. AIA/St |
| BS EN 14219:2003 | Hexagon bolts with flange with metric fine pitch thread. Small series |
| ISO 15980:2002 | Open end blind rivets with break pull mandrel and countersunk head — St/St |
| BS EN ISO 15977:2002 | Open end blind rivets with break pull mandrel and protruding head. AIA/St |
| ISO 16583:2002 | Open end blind rivets with break pull mandrel and countersunk head — Cu/St or Cu/Br or Cu/SSt |
| ISO 15975:2002 | Closed end blind rivets with break pull mandrel and protruding head — AI/AIA |
| ISO 16582:2002 | Open end blind rivets with break pull mandrel and protruding head — Cu/St or Cu/Br or Cu/SSt |
| ISO 15973:2000 | Closed end blind rivets with break pull mandrel and protruding head — AlA/St |
| ISO 15979:2002 | Open end blind rivets with break pull mandrel and protruding head — St/St |
| ISO 16426:2002 | Fasteners — Quality assurance system |
| BS EN ISO 6157-2:2004 | Fasteners. Surface discontinuities Nuts |
| ISO 15976:2002 | Closed end blind rivets with break pull mandrel and protruding head — St/St |
| ISO 15983:2002 | Open end blind rivets with break pull mandrel and protruding head — A2/A2 |
| ISO 15978:2002 | Open end blind rivets with break pull mandrel and countersunk head — AIA/St |
| BS EN 14399-4:2005 | High-strength structural bolting assemblies for preloading System HV. Hexagon bolt and nut assemblies |
| ISO 16584:2002 | Open end blind rivets with break pull mandrel and protruding head — NiCu/St or NiCu/SSt |
| ISO 4026:2003 | Hexagon socket set screws with flat point |
| DIN EN ISO 4026:2004-05 | Hexagon socket set screws with flat point (ISO 4026:2003); German version EN ISO 4026:2003 |
| DIN EN ISO 4028:2004-05 | Hexagon socket set screws with dog point (ISO 4028:2003); German version EN ISO 4028:2003 |
| EN 1515-4:2009 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| EN ISO 15982:2002 | Open end blind rivets with break pull mandrel and countersunk head - AIA/AIA (ISO 15982:2002) |
| EN ISO 16585:2002 | Closed end blind rivets with pull mandrel and protruding head - A2/SSt (ISO 16585:2002) |
| EN ISO 15976:2002 | Closed end blind rivets with break pull mandrel and protrudiing head - St/St (ISO 15976:2002) |
| EN ISO 15977:2002 | Open end blind rivets with break pull mandrel and protruding head - AIA/St (ISO 15977:2002) |
| EN ISO 16582:2002 | Open end blind rivets with break pull mandrel and protruding head - Cu/St or Cu/Br or Cu/SSt (ISO 16582:2002) |
| EN 14399-9:2018 | High-strength structural bolting assemblies for preloading - Part 9: System HR or HV - Direct tension indicators for bolt and nut assemblies |
| EN ISO 15983:2002 | Open end blind rivets with break pull mandrel and protruding head - A2/A2 (ISO 15983:2002) |
| EN ISO 15979:2002 | Open end blind rivets with break pull mandrel and protruding head - St/St (ISO 15979:2002) |
| EN ISO 15978:2002 | Open end blind rivets with break pull mandrel and countersunk head - AIA/St (ISO 15978:2002) |
| EN 14218:2003 | Hexagon nuts with flange - Fine pitch thread (ISO 10663:1999, modified) |
| EN 14399-5:2015 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| EN ISO 15981:2002 | Open end blind rivets with break pull mandrel and protruding head - AIA/AIA (ISO 15981:2002) |
| EN 14399-4:2015 | High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies |
| EN ISO 15984:2002 | Open end blind rivets with break pull mandrel and countersunk head - A2/A2 (ISO 15984:2002) |
| EN ISO 16584:2002 | Open end blind rivets with break pull mandrel and protruding head - NiCu/St or NiCu/SSt (ISO 16584:2002) |
| EN ISO 6157-2:2004 | Fasteners - Surface discontinuities - Part 2: Nuts (ISO 6157-2:1995) |
| EN ISO 4026:2003 | Hexagon socket set screws with flat point (ISO 4026:2003) |
| EN ISO 15974:2000 | Closed end blind rivets with break pull mandrel and countersunk head - AIA/St (ISO 15974:2000) |
| EN ISO 15975:2002 | Closed end blind rivets with break pull mandrel and protrudiing head - AI/AIA (ISO 15975:2002) |
| EN ISO 16426:2002 | Fasteners - Quality assurance system (ISO 16426:2002) |
| EN 14399-3:2015 | High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies |
| EN ISO 16583:2002 | Open end blind rivets with break pull mandrel and countersunk head - Cu/St or Cu/Br or Cu/SSt (ISO 16583:2002) |
| EN 14399-6:2015 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| BS EN 16983:2016 | Disc springs. Quality specifications. Dimensions |
| DIN EN 14219:2003-09 | Hexagon bolts with flange with metric fine pitch thread - Small series (ISO 15072:1999, modified) |
| I.S. EN ISO 6157-2:2004 | FASTENERS - SURFACE DISCONTINUITIES - PART 2: NUTS |
| 15/30332545 DC : 0 | BS EN 14399-7 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES |
| PREN 14399-4 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES |
| DIN EN 1515-4:2010-04 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| 15/30332554 DC : 0 | BS EN 14399-9 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| PREN 14399-7 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES |
| I.S. EN 14399-7:2007 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES |
| BS EN 14399-9:2009 | High strength structural bolting for preloading System HR or HV. Direct tension indicators for bolt and nut assemblies |
| I.S. EN 14399-8:2007 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| I.S. EN 14399-9:2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| DIN EN 14399-5:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| DIN EN 14399-4:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES |
| DIN EN 14399-6:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| BS EN ISO 16582:2002 | Open end blind rivets with break pull mandrel and protruding head. Cu/St or Cu/Br or Cu/SSt |
| BS EN ISO 15984:2002 | Open end blind rivets with break pull mandrel and countersunk head. A2/A2 |
| BS EN ISO 16584:2002 | Open end blind rivets with break pull mandrel and protruding head. NiCu/St or NiCu/SSt |
| BS EN ISO 15979:2002 | Open end blind rivets with break pull mandrel and protruding head. St/St |
| ISO 15977:2002 | Open end blind rivets with break pull mandrel and protruding head — AIA/St |
| BS EN ISO 4026:2003 | Hexagon socket set screws with flat point |
| ISO 15984:2002 | Open end blind rivets with break pull mandrel and countersunk head — A2/A2 |
| BS EN ISO 15975:2002 | Closed end blind rivets with break pull mandrel and protruding head. AI/AIA |
| DIN EN 14218:2003-09 | HEXAGON NUTS WITH FLANGE - FINE PITCH THREAD |
| DIN EN ISO 2342:2004-05 | Slotted headless screws with shank (ISO 2342:2003); German version EN ISO 2342:2003 |
| DIN EN ISO 15977:2011-02 | Open end blind rivets with break pull mandrel and protruding head - AlA/St (ISO 15977:2002) |
| I.S. EN 14219:2003 | HEXAGON BOLTS WITH FLANGE WITH METRIC FINE PITCH THREAD - SMALL SERIES |
| I.S. EN 14218:2003 | HEXAGON NUTS WITH FLANGE - FINE PITCH THREAD |
| UNE-EN 14399-5:2016 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| UNE-EN 1515-4:2010 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| UNE-EN 14399-3:2016 | High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies |
| UNE-EN 14399-6:2016 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| UNE-EN 14399-4:2016 | High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies |
| ISO 8839:1986 | Mechanical properties of fasteners — Bolts, screws, studs and nuts made of non-ferrous metals |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| ISO 10683:2014 | Fasteners — Non-electrolytically applied zinc flake coatings |
| EN 26157-3:1991 | Fasteners - Surface discontinuities - Part 3: Bolts, screws and studs for special requirements (ISO 6157-3:1988) |
| ISO 4759-3:2016 | Tolerances for fasteners — Part 3: Washers for bolts, screws and nuts — Product grades A, C and F |
| ISO 4042:1999 | Fasteners — Electroplated coatings |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws and studs |
| ISO 6157-3:1988 | Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements |
| EN ISO 4042:1999 | Fasteners - Electroplated coatings (ISO 4042:1999) |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:2009) |
| ISO 6157-1:1988 | Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements |
| EN 26157-1:1991 | Fasteners - Surface discontinuities - Part 1: Bolts, screws and studs for general requirements (ISO 6157-1:1988) |
| ISO 2320:2015 | Fasteners — Prevailing torque steel nuts — Functional properties |
| EN ISO 4759-3:2016 | Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016) |
| ISO 7085:1999 | Mechanical and performance requirements of case hardened and tempered metric thread rolling screws |
| ISO 8402:1994 | Quality management and quality assurance — Vocabulary |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| ISO 1502:1996 | ISO general-purpose metric screw threads — Gauges and gauging |
| ISO 898-6:1994 | Mechanical properties of fasteners — Part 6: Nuts with specified proof load values — Fine pitch thread |
| ISO 898-5:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 5: Set screws and similar threaded fasteners with specified hardness classes — Coarse thread and fine pitch thread |
| ISO 3506:1979 | Corrosion-resistant stainless steel fasteners — Specifications |
| ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners — Part 3: Set screws and similar fasteners not under tensile stress |
| EN ISO 2702:2011 | Heat-treated steel tapping screws - Mechanical properties (ISO 2702:2011) |
| ISO 3534-2:2006 | Statistics — Vocabulary and symbols — Part 2: Applied statistics |
| EN ISO 898-5:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread (ISO 898-5:2012) |
| EN ISO 2320:2015 | Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015) |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| ISO 6157-2:1995 | Fasteners — Surface discontinuities — Part 2: Nuts |
| EN ISO 898-6:1995 | Mechanical properties of fasteners - Part 6: Nuts with specified proof load values - Fine pitch thread (ISO 898-6:1994) |
| ISO 8992:2005 | Fasteners — General requirements for bolts, screws, studs and nuts |
| EN ISO 7085 : 1999 | MECHANICAL AND PERFORMANCE REQUIREMENTS OF CASE HARDENED AND TEMPERED METRIC THREAD ROLLING SCREWS |
| ISO 2702:2011 | Heat-treated steel tapping screws — Mechanical properties |
| ISO 1478:1999 | Tapping screws thread |
| EN 28839:1991 | Mechanical properties of fasteners - Bolts, screws, studs and nuts made of non-ferrous metals (ISO 8839:1986) |
| EN ISO 1478:1999 | Tapping screws thread (ISO 1478:1999) |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners — Part 2: Nuts |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Sorry this product is not available in your region.