EN ISO 15874-2:2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2013)
Amended by
Superseded date
04-01-2020
Published date
20-02-2013
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 Material
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics
8 Physical and chemical characteristics
9 Performance requirements
10 Marking
Annex A (informative) - Derivation of S[calc,max]
Bibliography
ISO 15874-2:2013 specifies the requirements of pipes made from polypropylene (PP) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems under operating pressures and temperatures appropriate to the class of application.It covers a range of service conditions (application classes), design pressures and pipe dimension classes.It also specifies test parameters for test methods.In conjunction with the other parts of ISO 15874, ISO 15874-2:2013 is applicable to PP pipes, their joints and to joints with components of PP, other plastics and non-plastics materials intended to be used for hot and cold water installations.It is applicable to pipes with or without (a) barrier layer(s).
| Committee |
CEN/TC 155
|
| DevelopmentNote |
Supersedes PREN ISO 15874-2. (03/2013)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| Supersedes |
| Standards | Relationship |
| DIN EN ISO 15874-2:2004-03 | Identical |
| NEN EN ISO 15874-2 : 2013 | Identical |
| NBN EN ISO 15874-2 : 2013 | Identical |
| ISO 15874-2:2013 | Identical |
| SS EN ISO 15874-2:2013 | Identical |
| BS EN ISO 15874-2 : 2013 | Identical |
| SN EN ISO 15874-2:2013 | Identical |
| UNI EN ISO 15874-2 : 2013 | Identical |
| NF EN ISO 15874-2 : 2013 | Identical |
| PN EN ISO 15874-2 : 2013 | Identical |
| DIN EN ISO 15874-2:2013-06 | Identical |
| DIN EN ISO 15874-2:2018-11 | Identical |
| UNE-EN ISO 15874-2:2013/A1:2018 | Identical |
| UNE-EN ISO 15874-2:2013 | Identical |
| I.S. EN ISO 15874-2:2013 | Identical |
| NS EN ISO 15874-2 : 2013 | Identical |
| ONORM EN ISO 15874-2 : 2013 | Identical |
| DIN EN 1254-6:2012-12 | Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends |
| 11/30197617 DC : 0 | BS ISO 11855-5 - BUILDING ENVIRONMENT DESIGN - STANDARDS FOR THE DESIGN, CONSTRUCTION AND OPERATION OF RADIANT HEATING AND COOLING SYSTEMS - PART 5: INSTALLATION |
| PREN 1254-6 : DRAFT 2011 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTING WITH PUSH-FIT ENDS |
| EN ISO/TS 15874-7 : 2003 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| NF EN 1264-4 : 2010 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| I.S. EN 1264-4:2009 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| DIN EN ISO 15874-1:2004-03 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) |
| DIN EN ISO 15874-5:2004-03 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM |
| DIN EN ISO 15874-3:2004-03 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 3: FITTINGS |
| 11/30239909 DC : 0 | BS EN 15015 - PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| 09/30202316 DC : 0 | BS EN 12514-4 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES |
| 11/30213587 DC : 0 | BS EN 1254-6 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS |
| 07/19990369 DC : 0 | BS EN 806-4 - SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4 - INSTALLATION |
| EN 1264-4:2009 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| PREN 15015 : DRAFT 2014 | PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| ISO/TS 15874-7:2003 | Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity |
| DIN EN 1264-4:2009-11 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| BS EN 1264-4:2009 | Water based surface embedded heating and cooling systems Installation |
| UNI EN 15015 : 2008 | PLASTICS PIPING SYSTEMS - SYSTEMS FOR HOT AND COLD WATER NOT INTENDED FOR HUMAN CONSUMPTION - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS |
| UNI EN 1254-6 : 2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS |
| DD CEN ISO/TS 15874-7:2003 | Plastics piping systems for hot and cold water installations. Polypropylene (PP) Guidance for the assessment of conformity |
| UNI EN 1264-4 : 2009 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| I.S. EN 1254-6:2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS |
| 14/30297462 DC : 0 | BS EN 15015 - PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| BS EN 806-2:2005 | Specifications for installations inside buildings conveying water for human consumption Design |
| EN 806-2:2005 | Specification for installations inside buildings conveying water for human consumption - Part 2: Design |
| BS EN 1254-6:2012 | Copper and copper alloys. Plumbing fittings Fittings with push-fit ends |
| I.S. EN ISO/TS 15874-7:2004 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS POLYPROPYLENE (PP) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| EN 1254-6:2012 | Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends |
| UNE-EN 1254-6:2013 | Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends |
| 07/30168416 DC : 0 | BS EN 1264-4 - WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| UNI EN 806-2 : 2008 | SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 2: DESIGN |
| DIN EN 806-2:2005-06 | Specification for installations inside buildings conveying water for human consumption - Part 2: Design |
| UNE-EN 1264-4:2010 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| ISO 15874-3:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 3: Fittings |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| ISO 15874-1:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 1: General |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 9854-1:1994 | Thermoplastics pipes for the transport of fluids — Determination of pendulum impact strength by the Charpy method — Part 1: General test method |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| CEN/TR 12108:2012 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| ISO 9854-2:1994 | Thermoplastics pipes for the transport of fluids — Determination of pendulum impact strength by the Charpy method — Part 2: Test conditions for pipes of various materials |
| ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
| ISO 13760:1998 | Plastics pipes for the conveyance of fluids under pressure — Miner's rule — Calculation method for cumulative damage |
| ISO 15874-5:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 5: Fitness for purpose of the system |
| ISO/TS 15874-7:2003 | Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity |
| ISO 7686:2005 | Plastics pipes and fittings — Determination of opacity |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.