EN ISO 13000-2:2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005)
09-09-2021
15-11-2005
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Sampling
5 Preparation of test specimens
6 Testing of semi-finished PTFE products
6.1 General
6.2 Linear dimensions
6.3 Tensile properties
6.4 Density
6.5 Loss in mass at 300 degree C
6.6 Dimensional stability - General method
6.7 Dimensional stability - Special method for the
determination of the dimensional and the
geometrical stability of thick-walled tubes
6.8 Electrical properties
6.9 Hardness
6.10 Colour
6.11 Radiographic examination
6.12 Resistance to environmental stress cracking (ESC)
6.13 Deformation under load
Annex A (informative) Other standards relating to testing
semi-finished products of PTFE
ISO 13000-2:2005 specifies the preparation of test specimens and gives the test methods applicable to semi-finished products of polytetrafluoroethylene (PTFE).
| Committee |
CEN/TC 249
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ONORM EN ISO 13000-2 : 2006 | Identical |
| BS EN ISO 13000-2:2021 | Identical |
| UNE-EN ISO 13000-2:2006 | Identical |
| PN EN ISO 13000-2 : 2007 | Identical |
| NF EN ISO 13000-2 : 2006 | Identical |
| I.S. EN ISO 13000-2:2006 | Identical |
| BS EN ISO 13000-2:2005 | Identical |
| NS EN ISO 13000-2 : 2ED 2006 | Identical |
| NEN EN ISO 13000-2 : 2005 | Identical |
| UNI EN ISO 13000-2 : 2006 | Identical |
| NBN EN ISO 13000-2 : 2006 | Identical |
| SN EN ISO 13000-2 : 2006 | Identical |
| ISO 13000-2:2005 | Identical |
| DIN EN ISO 13000-2:2006-02 | Identical |
| 04/30091874 DC : DRAFT FEB 2004 | BS EN ISO 13000-1 - PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 1: REQUIREMENTS AND DESIGNATION |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| ASTM D 3418 : 2015 : REDLINE | Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ISO 12086-1:2006 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 1: Designation system and basis for specifications |
| IEC 60684-2:2011 | Flexible insulating sleeving - Part 2: Methods of test |
| BS 6564-3:1990 | Polytetrafluoroethylene (PTFE) materials and products Specification for E glass fibre filled polytetrafluoroethylene |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 1923:1981 | Cellular plastics and rubbers — Determination of linear dimensions |
| ISO 2039-1:2001 | Plastics Determination of hardness Part 1: Ball indentation method |
| ASTM D 3294 : 2015 : REDLINE | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet and Molded Basic Shapes |
| IEC 60684-1:2003 | Flexible insulating sleeving - Part 1: Definitions and general requirements |
| ISO 12086-2:2006 | Plastics Fluoropolymer dispersions and moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties |
| ASTM D 3295 : 2015 : REDLINE | Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ASTM D 3369 : 2001 | Standard Specification for Polytetrafluoroethylene (PTFE) Resin Cast Film (Withdrawn 2006) |
| ISO 472:2013 | Plastics — Vocabulary |
| ISO 13000-1:2005 | Plastics Polytetrafluoroethylene (PTFE) semi-finished products Part 1: Requirements and designation |
| ISO 3611:2010 | Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics |
| ISO 4599:1986 | Plastics Determination of resistance to environmental stress cracking (ESC) Bent strip method |
| IEC 60243-2:2013 | Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage |
| IEC 60674-2:2016 | Specification for plastic films for electrical purposes - Part 2: Methods of test |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| ISO 4600:1992 | Plastics Determination of environmental stress cracking (ESC) Ball or pin impression method |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
| ASTM D 4969 : 2017 : REDLINE | Standard Specification for Polytetrafluoroethylene–(PTFE) Coated Glass Fabric |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.