EN ISO 11114-4:2017
Current
Current
The latest, up-to-date edition.
Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 4: Test methods for selecting steels resistant to hydrogen embrittlement (ISO 11114-4:2017)
Published date
26-04-2017
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviated terms
4 General requirements
5 Test methods
Bibliography
ISO 11114-4: 2017 specifies test methods and the evaluation of results from these tests in order to qualify steels suitable for use in the manufacture of gas cylinders (up to 3 000 l) for hydrogen and hydrogen bearing embrittling gases.This document only applies to seamless steel gas cylinders.The requirements of this document are not applicable if at least one of the following conditions for the intended gas service is fulfilled:- the working pressure of the filled embrittling gas is less than 20 % of the test pressure of the cylinder;- the partial pressure of the filled embrittling gas of a gas mixture is less than 5 MPa (50 bar) in the case of hydrogen and other embrittling gases, with the exception of hydrogen sulphide and methyl mercaptan; in such cases, the partial pressure shall not exceed 0,25 MPa (2,5 bar).NOTE In such cases, it is possible to design the cylinder as for ordinary (non-embrittling) gases.
| Committee |
CEN/TC 23
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| DIN EN ISO 11114-4:2017-09 | Identical |
| BS EN ISO 11114-4:2005 | Identical |
| NBN EN ISO 11114-4 : 2005 | Identical |
| NS EN ISO 11114-4 : 2017 | Identical |
| UNI EN ISO 11114-4 : 2005 | Identical |
| NEN EN ISO 11114-4 : 2017 | Identical |
| UNE-EN ISO 11114-4:2017 | Identical |
| UNI EN ISO 11114-4 : 2017 | Identical |
| DIN EN ISO 11114-4:2015-08 (Draft) | Identical |
| ISO 11114-4:2017 | Identical |
| I.S. EN ISO 11114-4:2017 | Identical |
| SN EN ISO 11114-4:2017 | Identical |
| PN EN ISO 11114-4 : 2017 | Identical |
| NF EN ISO 11114-4 : 2017 | Identical |
| BS EN ISO 11114-4:2017 | Identical |
| I.S. EN ISO 9809-2:2010 | GAS CYLINDERS - REFILLABLE SEAMLESS STEEL GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTING - PART 2: QUENCHED AND TEMPERED STEEL CYLINDERS WITH TENSILE STRENGTH GREATER THAN OR EQUAL TO 1100 MPA |
| BS EN 13807:2017 | Transportable gas cylinders. Battery vehicles and multiple-element gas containers (MEGCs). Design, manufacture, identification and testing |
| BS EN ISO 9809-1:2010 | Gas cylinders. Refillable seamless steel gas cylinders. Design, construction and testing Quenched and tempered steel cylinders with tensile strength less than 1100 MPa |
| UNI EN ISO 9809-3 : 2010 | GAS CYLINDERS - REFILLABLE SEAMLESS STEEL GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTING - PART 3: NORMALIZED STEEL CYLINDERS |
| UNI EN ISO 9809-1 : 2010 | GAS CYLINDERS - REFILLABLE SEAMLESS STEEL GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTING - PART 1: QUENCHED AND TEMPERED STEEL CYLINDERS WITH TENSILE STRENGTH LESS THAN 1100 MPA |
| I.S. EN ISO 9809-3:2010 | GAS CYLINDERS - REFILLABLE SEAMLESS STEEL GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTING - PART 3: NORMALIZED STEEL CYLINDERS |
| I.S. EN 13807:2017 | TRANSPORTABLE GAS CYLINDERS - BATTERY VEHICLES - DESIGN, MANUFACTURE, IDENTIFICATION AND TESTING |
| NF EN 12245 : 2009 + A1 2012 | TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS |
| BS EN ISO 9809-2:2010 | Gas cylinders. Refillable seamless steel gas cylinders. Design, construction and testing Quenched and tempered steel cylinders with tensile strength greater than or equal to 1100 MPa |
| BS EN ISO 9809-3:2010 | Gas cylinders. Refillable seamless steel gas cylinders. Design, construction and testing Normalized steel cylinders |
| DIN EN 12245:2012-03 | Transportable gas cylinders - Fully wrapped composite cylinders (includes Amendment A1:2011) |
| DIN EN 13807:2016-02 (Draft) | TRANSPORTABLE GAS CYLINDERS - BATTERY VEHICLES AND MULTIPLE-ELEMENT GAS CONTAINERS (MEGCS) - DESIGN, MANUFACTURE, IDENTIFICATION AND TESTING |
| UNE-EN 13807:2017 | Transportable gas cylinders - Battery vehicles and multiple-element gas containers (MEGCs) - Design, manufacture, identification and testing |
| UNI EN 12245 : 2011 | TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS |
| BS EN 62282-4-101:2014 | Fuel cell technologies Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU). Safety of electrically powered industrial trucks |
| ISO 9809-2:2010 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa |
| ISO 9809-3:2010 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 3: Normalized steel cylinders |
| ISO 9809-1:2010 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa |
| UNE-EN 12245:2009 | Transportable gas cylinders - Fully wrapped composite cylinders |
| EN ISO 9809-1:2010 | Gas cylinders - Refillable seamless steel gas cylinders - Design, construction and testing - Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa (ISO 9809-1:2010) |
| EN ISO 9809-3:2010 | Gas cylinders - Refillable seamless steel gas cylinders - Design, construction and testing - Part 3: Normalized steel cylinders (ISO 9809-3:2010) |
| EN ISO 9809-2:2010 | Gas cylinders - Refillable seamless steel gas cylinders - Design, construction and testing - Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa (ISO 9809-2:2010) |
| EN 12245:2009+A1:2011 | Transportable gas cylinders - Fully wrapped composite cylinders |
| EN 13807:2017 | Transportable gas cylinders - Battery vehicles and multiple-element gas containers (MEGCs) - Design, manufacture, identification and testing |
| I.S. EN ISO 9809-1:2010 | GAS CYLINDERS - REFILLABLE SEAMLESS STEEL GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTING - PART 1: QUENCHED AND TEMPERED STEEL CYLINDERS WITH TENSILE STRENGTH LESS THAN 1100 MPA |
| UNI EN ISO 9809-2 : 2010 | GAS CYLINDERS - REFILLABLE SEAMLESS STEEL GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTING - PART 2: QUENCHED AND TEMPERED STEEL CYLINDERS WITH TENSILE STRENGTH GREATER THAN OR EQUAL TO 1100 MPA |
| DIN EN 13807:2017-05 | TRANSPORTABLE GAS CYLINDERS - BATTERY VEHICLES AND MULTIPLE-ELEMENT GAS CONTAINERS (MEGCS) - DESIGN, MANUFACTURE, IDENTIFICATION AND TESTING |
| EN 62282-4-101:2014 | Fuel cell technologies - Part 4-101: Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU) - Safety of electrically powered industrial trucks |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 11114-1:2012 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials |
| ISO 9809-3:2010 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 3: Normalized steel cylinders |
| FD E29 753 : 2014 FD | GAS CYLINDERS - HYDROGEN COMPATIBILITY TESTING FOR METALS |
| ISO 9809-4:2014 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 4: Stainless steel cylinders with an Rm value of less than 1 100 MPa |
| ISO 7539-6:2011 | Corrosion of metals and alloys Stress corrosion testing Part 6: Preparation and use of precracked specimens for tests under constant load or constant displacement |
| ISO 11120:2015 | Gas cylinders Refillable seamless steel tubes of water capacity between 150 l and 3000 l Design, construction and testing |
| ISO 9809-2:2010 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa |
| ISO 7539-1:2012 | Corrosion of metals and alloys — Stress corrosion testing — Part 1: General guidance on testing procedures |
| ISO 9809-1:2010 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.