EN 61185:2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Ferrite cores (ETD-cores) intended for use in power supply applications - Dimensions
01-03-2016
30-06-2005
FOREWORD
1 Scope
2 Normative references
3 Primary standards
3.1 Dimensions of ETD-cores
3.2 Dimensional limits for coil formers
3.3 Pin locations and base outlines
3.4 Pin diameter
4 Marking
5 Mounting
Annex A (normative) Derived standards
Annex B (normative) Example of a standard for gauges
to check the dimensions of ETD-cores
meeting this primary standard
Annex ZA (normative) Normative references to international
publications with their corresponding
European publications
Specifies the dimensions that are of importance for mechanical interchangeability for ETD-cores made of ferrite, the essential dimensions of coil formers to be used with them, and the effective parameter values to be used in calculations involving them.
| Committee |
CLC/SR 51
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| BS EN 61185:2005 | Identical |
| PN EN 61185 : 2006 | Identical |
| DIN EN 61185:2006-01 | Identical |
| NBN EN 61185 : 2006 | Identical |
| IEC 61185:2005 | Identical |
| NEN EN IEC 61185 : 2005 | Identical |
| UNE-EN 61185:2005 | Identical |
| NF EN 61185 : 2005 | Identical |
| I.S. EN 61185:2005 | Identical |
| SN EN 61185 : 1997 | Identical |
| CEI EN 61185 : 2005 | Identical |
| PNE-prEN 61185 | Identical |
| I.S. EN 60424-3:2016 | FERRITE CORES - GUIDELINES ON THE LIMITS OF SURFACE IRREGULARITIES - PART 3: ETD-CORES, EER-CORES, EC-CORES AND E-CORES |
| BS EN 62358 : 2012 | FERRITE CORES - STANDARD INDUCTANCE FACTOR FOR GAPPED CORES AND ITS TOLERANCE |
| EN 60424-3:2016 | Ferrite cores - Guidelines on the limits of surface irregularities - Part 3: ETD-cores, EER-cores, EC-cores and E-cores |
| I.S. EN 62317-1:2007 | FERRITE CORES - DIMENSIONS - PART 1: GENERAL SPECIFICATION |
| EN 62317-1:2007 | Ferrite cores - Dimensions - Part 1: General specification |
| BS EN 62317-1:2007 | Ferrite cores. Dimensions General specification |
| CEI EN 62358 : 2013 | FERRITE CORES - STANDARD INDUCTANCE FACTOR FOR GAPPED CORES AND ITS TOLERANCE |
| BS EN 61860:2001 | Dimension of low-profile cores made of magnetic oxides |
| BS EN 60424-3:2016 | Ferrite cores. Guidelines on the limits of surface irregularities ETD-cores, EER-cores, EC-cores and E-cores |
| I.S. EN 62358:2012 | FERRITE CORES - STANDARD INDUCTANCE FACTOR FOR GAPPED CORES AND ITS TOLERANCE (IEC 62358:2012 (EQV)) |
| EN 62358:2012 | Ferrite cores - Standard inductance factor for gapped cores and its tolerance |
| IEC 60205:2016 | Calculation of the effective parameters of magnetic piece parts |
| EN 60205:2017 | Calculation of the effective parameters of magnetic piece parts |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.