EN 61076-1:2006
Current
Current
The latest, up-to-date edition.
Connectors for electronic equipment - Product requirements - Part 1: Generic specification
Amended by
Published date
09-06-2006
Sorry this product is not available in your region.
FOREWORD
INTRODUCTION
1 General
1.1 Scope
1.2 General considerations relating to specifications
1.3 Normative references
1.4 Performance characteristics
2 Technical information
2.1 Terms and definitions
2.2 System of levels
2.3 Classification into climatic categories
2.4 Clearance and creepage distances
2.5 Current-carrying capacity
2.6 IEC type designation
2.7 Marking
3 Dimensional information
3.1 Drawings and dimensions
3.2 System of lettering
3.3 Purpose
3.4 Detailed information
3.5 Gauges
4 Quality assessment procedures
5 Tests and test schedules
5.1 General aspects
5.2 Test schedules
5.3 Test procedures and measuring methods
5.4 Preconditioning
5.5 Wiring and mounting of specimens
Annex A (normative) Common lettering system to be used
in drawings
Annex ZA (normative) Normative references to international
publications with there corresponding European
publications
Establishes uniform specifications and technical information for connectors. Is applicable to a family of connectors for use in electronic and electrical equipment; does not cover connectors designed for use at radio frequencies.
| Committee |
CLC/SR 48B
|
| DevelopmentNote |
To be read in conjunction with EN 62197-1 (07/2006) Supersedes UNE EN 61076-1. (05/2009)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| I.S. EN 61076-1:2006/A1:2019 | Identical |
| SN EN 61076-1 : 2006 | Identical |
| NEN EN IEC 61076-1 : 2006 | Identical |
| IEC 61076-1:2006 | Identical |
| BS EN 61076-1:2006 | Identical |
| UNE EN 61076-1 : 1997 A2 2002 | Identical |
| PN EN 61076-1 : 2007 | Identical |
| CEI EN 61076-1 : 2007 | Identical |
| DIN EN 61076-1:2019-10 | Identical |
| NF EN 61076-1 : 2006 | Identical |
| NBN EN 61076-1 : 2006 | Identical |
| DIN EN 61076-1:2007-02 | Identical |
| UNE EN 61076-1 : 1997 A2 2002 | Identical |
| PNE-prEN 61076-1 | Identical |
| UNE-EN 61076-1:2006 | Identical |
| BS EN 61076-3-115:2010 | Connectors for electronic equipment. Product requirements Rectangular connectors. Detail specification for protective housings for use with 8-way shielded and unshielded connectors for frequencies up to 600 MHz for industrial environments incorporating the IEC 60603-7 series interface. Variant 12 related to IEC 61076-3-106. Push-pull type |
| BS EN 61076-3-122:2017 | Connectors for electrical and electronic equipment. Product requirements Detail specification for 8-way, shielded, free and fixed connectors for I/O and Gigabit Ethernet applications in harsh environments |
| BS EN 61076-3-112:2006 | Connectors for electronic equipment Rectangular connectors - Detail specification for rectangular connectors with four contacts for high performance serial bus for consumer audio/video equipment |
| BS EN 61076-2-107:2010 | Connectors for electronic equipment. Product requirements Detail specification for circular hybrid connectors M12 with electrical and fibre-optic contacts with screw locking |
| BS EN 61076-4-115:2003 | Connectors for electronic equipment. Printed board connectors with assessed quality Backplane connector for InfiniBand equipment |
| NF EN 61076 4 100 : 2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-100: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES HAVING A GRID OF 2,5 MM FOR PRINTED BOARDS AND BACKPLANES |
| BS EN 60512-29-100:2015 | Connectors for electronic equipment. Tests and measurements Signal integrity tests up to 500 MHz on M12 style connectors. Tests 29a to 29g |
| BS EN 60512-27-100:2012 | Connectors for electronic equipment. Tests and measurements Signal integrity tests up to 500 MHz on IEC 60603-7 series connectors. Tests 27a to 27g |
| I.S. EN 61076-3-103:2004 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 3-103: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR SINGLE ROW CONNECTORS WITH NON-REMOVABLE RIBBON CABLE CONTACTS ON 1,25 MM PITCH USED FOR HIGH SPEED SERIAL DATA (HSSDC) |
| BS EN 61076-4-101:2001 | Connectors for electronic equipment Printed board connectors with assessed quality. Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917 |
| CEI EN 61076-3-116 : 2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-116: RECTANGULAR CONNECTORS - PROTECTIVE HOUSINGS FOR USE WITH 8- WAY SHIELDED AND UNSHIELDED CONNECTORS FOR FREQUENCIES UP TO 600 MHZ FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE - VARIANT 13 RELATED TO IEC 61076-3-106 - LOCKING LEVER |
| BS EN 61076-3-100:2000 | Connectors for use in d.c., low-frequency analogue and digital high-speed data applications Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row |
| CEI EN 61076-7-100 : 2007 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS PART 7-100: CABLE OUTLET ACCESSORIES - DETAIL SPECIFICATION FOR A METRIC CABLE SEALING CONSISTING OF AN INTEGRATED PART OF HEAVY-DUTY RECTANGULAR OR CIRCULAR CONNECTOR HOODS AND A SEALING SYSTEM |
| CEI EN 61076-2-102 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 2-102: CIRCULAR CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR PLUGS AND JACKS FOR EXTERNAL LOW VOLTAGE POWER SUPPLY |
| I.S. EN 60512-27-100:2012 | CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 27-100: SIGNAL INTEGRITY TESTS UP TO 500 MHZ ON IEC 60603-7 SERIES CONNECTORS - TESTS 27A TO 27G (IEC 60512-27-100:2011 (EQV)) |
| I.S. EN 61076-3-117:2009 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-117: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR PROTECTIVE HOUSINGS OR USE WITH 8-WAY SHIELDED AND UNSHIELDED CONNECTORS FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE - VARIANT 14 RELATED TO IEC 61076-3-106 - PUSH-PULL COUPLING |
| I.S. EN 61076-4-101:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-101: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES, HAVING A BASIC GRID OF 2,0 MM FOR PRINTED BOARDS AND BACKPLANES IN ACCORDANCE WITH IEC 60917 |
| I.S. EN 61076-3-120:2016 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-120: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR REWIRABLE POWER CONNECTORS WITH SNAP LOCKING FOR RATED VOLTAGE OF 250 V D.C. AND RATED CURRENT OF 30 A |
| I.S. EN 61076-3-112:2006 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 3-112: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR RECTANGULAR CONNECTORS WITH FOUR CONTACTS FOR HIGH PERFORMANCE SERIAL BUS FOR CONSUMER AUDIO/VIDEO EQUIPMENT |
| CEI EN 61076-4-111 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-111: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART POWER CONNECTOR MODULES, FOR PRINTED BOARDS AND BACKPLANES HAVING EARLY MATING FEATURES, AND HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1 |
| I.S. EN 61076-3-116:2008 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-116: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR PROTECTIVE HOUSINGS FOR USE WITH 8-WAY SHIELDED AND UNSHIELDED CONNECTORS FOR FREQUENCIES UP TO 600 MHZ FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE - VARIANT 13 RELATED TO IEC 61076-3-106 - LOCKING LEVER |
| I.S. EN 61076-2-001:2011 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-001: CIRCULAR CONNECTORS - BLANK DETAIL SPECIFICATION |
| CEI EN 61076-3-106 : 2007 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-106: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR PROTECTIVE HOUSINGS FOR USE WITH 8-WAY SHIELDED AND UNSHIELDED CONNECTORS FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE |
| CEI EN 60512-29-100 : 2016 | CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 29-100: SIGNAL INTEGRITY TESTS UP TO 500 MHZ ON M12 STYLE CONNECTORS - TESTS 29A TO 29G |
| I.S. EN 61076-4-103:1999 | CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4-103: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH SHIELDING AND A BASIC GRID OF 2.5 MM |
| I.S. EN 61076-2-105:2008 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-105: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR M5 CONNECTORS WITH SCREW-LOCKING |
| EN 175301-801:2006 | Detail Specification: High density rectangular connectors, round removable crimp contacts |
| EN 62197-1 : 2006 | CONNECTORS FOR ELECTRONIC EQUIPMENT - QUALITY ASSESSMENT REQUIREMENTS - PART 1: GENERIC SPECIFICATION |
| EN 61076-7-100 : 2006 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 7-100: CABLE OUTLET ACCESSORIES - DETAIL SPECIFICATION FOR A METRIC CABLE SEALING CONSISTING OF AN INTEGRATED PART OF HEAVY-DUTY RECTANGULAR OR CIRCULAR CONNECTOR HOODS AND A SEALING SYSTEM |
| EN 61076-4-108:2002 | Connectors for electronic equipment - Part 4-108: Printed board connectors with assessed quality - Detail specification for cable-to-board connectors, with a modular pitch of 25 mm and integrated shielding function, applicable for transverse packing density of 15 mm, having a basic grid of 2,5 mm in accordance with IEC 60917-1 |
| EN 61076-4-101:2001 | Connectors for electronic equipment - Part 4-101: Printed board connectors with assessed quality - Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917 |
| EN 60603-7-5:2010 | Connectors for electronic equipment - Part 7-5: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz |
| EN 61076-3-114 : 2009 | Connectors for electronic equipment - Product requirements - Part 3-114: Rectangular connectors - Detail specification for protective housings for use with 8-way shielded and unshielded connectors for frequencies up to 600 MHz for industrial environments incorporating the IEC 60603-7 series interface - Variant 11 related to IEC 61076-3-106 - Bayonet coupling type |
| EN 61076-3-116 : 2008 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-116: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR PROTECTIVE HOUSINGS FOR USE WITH 8-WAY SHIELDED AND UNSHIELDED CONNECTORS FOR FREQUENCIES UP TO 600 MHZ FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE - VARIANT 13 RELATED TO IEC 61076-3-106 - LOCKING LEVER |
| EN 61076-2:2011 | Connectors for electronic equipment - Product requirements - Part 2: Sectional specification for circular connectors |
| EN 61076-4-114:2003 | Connectors for electronic equipment - Part 4-114: Printed board connectors - Detail specification for two-part connector with integrated shielding function having a grid of 1 mm x 1,5 mm |
| EN 61076-7-001:2004 | Connectors for electronic equipment - Part 7-001: Cable outlet accessories - Blank detail specification |
| EN 61076-2-106:2011 | Connectors for electronic equipment - Product requirements - Part 2-106: Circular connectors - Detail specification for connectors M 16 x 0,75 with screw-locking and degree of protection IP40 or IP65/67 |
| EN 61076-4-103:1999 | Connectors for use in d.c. low-frequency analogue and digital high speed data applications - Part 4-103: Printed board connectors with assessed quality - Detail specification for two-part connectors with shielding and a basic grid of 2,5 mm |
| EN 61076-4-102:1997 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications - Part 4: Printed board connectors - Section 102: Detail specification for two-part single-pole connectors, for multiple uses on plug-in units, with pre-centring, coding and early mating features, having a metric grid in accordance with IEC 60917 |
| EN 61076-3-101:1997 | Connectors with assessed quality, for use in d.c. low-frequency analogue and in digital high-speed data applications - Part 3: Rectangular connectors - Section 101: Detail specification for a range of shielded connectors with trapezoidal shaped shells and non-removable rectangular contacts on a 1,27 mm x 2,54 mm centre-line |
| EN 61076-2-104:2014 | Connectors for electronic equipment - Product requirements - Part 2-104: Circular connectors - Detail specification for circular connectors with M8 screw-locking or snap-locking |
| EN 60512-27-100:2012 | Connectors for electronic equipment - Tests and measurements - Part 27-100: Signal integrity tests up to 500 MHz on IEC 60603-7 series connectors - Tests 27a to 27g |
| EN 60512-29-100:2015 | Connectors for electronic equipment - Tests and measurements - Part 29-100: Signal integrity tests up to 500 MHz on M12 style connectors - Tests 29a to 29g |
| EN 61076-4-113:2003 | Connectors for electronic equipment - Printed board connectors - Part 4-113: Detail specification for two-part connectors having 5 rows with a grid of 2,54 mm for printed boards and backplanes in bus applications |
| EN 61076-4-001:1996 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high-speed data applications - Part 4: Printed board connectors - Section 001: Blank detail specification |
| EN 61076-4-110:2002 | Connectors for electronic equipment - Part 4-110: Printed board connectors with assessed quality - Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function |
| BS EN 61076-2-106:2011 | Connectors for electronic equipment. Product requirements Circular connectors. Detail specification for connectors M 16 x 0,75 with screw-locking and degree of protection IP40 or IP65/67 |
| BS EN 61076-4-111:2002 | Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for two-part power connector modules, for printed boards and backplanes having early mating features, and having a basic grid of 2,5 mm in accordance with IEC 60917-1 |
| BS EN 61076-4-102:1997 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for two-part single-pole connectors, for multiple uses on plug-in units, with pre-centring, coding and early mating features, having a metric grid in accordance with IEC 60917 |
| I.S. EN 61076-4:1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: SECTIONAL SPECIFICATION - PRINTED BOARD CONNECTORS |
| BS EN 61076-3-101 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTRE-LINE |
| BS EN 61076-2-001:2011 | Connectors for electronic equipment. Product requirements Circular connectors. Blank detail specification |
| BS EN 61076-3-106:2006 | Connectors for electronic equipment. Product requirements Rectangular connectors. Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface |
| BS EN 61076-2-105:2008 | Connectors for electronic equipment. Product requirements Circular connectors. Detail specification for M5 connectors with screw-locking |
| CEI EN 61076-4-110 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION |
| BS EN 61076-4-103:1999 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for two-part connectors with shielding and a basic grid of 2,5 mm - Cable to board connectors, shielded against EMC ,grid 2,5 mm,for high speed data rates,for use with printed boards |
| BS EN 61076-4-110:2002 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function |
| BS EN 61076-7-100:2006 | Connectors for electronic equipment. Product requirements Cable outlet accessories. Detail specification for a metric cable sealing consisting of an integrated part of heavy-duty rectangular or circular connector hoods and a sealing system |
| BS EN 61076-4-104:1999 | Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm - Detail specification for two part modular connectors (with optional shielding plates) for printed boards and backplanes, basic grid 2,0 mm, with terminations on a multiple grid of 0,5 mm |
| CEI EN 61076-2-106 : 2012 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-106: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR CONNECTORS M 16 X 0,75 WITH SCREW-LOCKING AND DEGREE OF PROTECTION IP40 OR IP65/67 |
| BS EN 61076-4-113:2003 | Connectors for electronic equipment Printed board connectors with assessed quality Detail specification for two-part connectors having 5 rows with a grid of 2,54 mm for printed boards and backplanes in bus applications |
| EN 61076-2-113:2017 | Connectors for electronic equipment - Product requirements - Part 2-113: Circular connectors - Detail specification for connectors with M12 screw locking with power and signal contacts for data transmission with frequency up to 100 MHz |
| CEI EN 61076-3-120 : 1ED 2017 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-120: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR REWIRABLE POWER CONNECTORS WITH SNAP LOCKING FOR RATED VOLTAGE OF 250 V D.C. AND RATED CURRENT OF 30 A |
| CEI EN 61076-3-112 : 2007 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 3-112: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR RECTANGULAR CONNECTORS WITH FOUR CONTACTS FOR HIGH PERFORMANCE SERIAL BUS FOR CONSUMER AUDIO/VIDEO EQUIPMENT |
| BS EN 61076-3-103:2004 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Rectangular connectors Detail specification for single row connectors with non-removable ribbon cable contacts on 1,25 mm pitch used for high speed serial data (HSSDC) |
| CEI EN 61076-4-115 : 2004 | CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-115: PRINTED BOARD CONNECTORS BACKPLANE CONNECTOR FOR INFINIBAND EQUIPMENT |
| BS EN 61076-3-116:2008 | Connectors for electronic equipment. Product requirements Rectangular connectors. Detail specification for protective housings for use with 8-way shielded and unshielded connectors for frequencies up to 600 MHz for industrial environments incorporating the IEC 60603-7 series interface. Variant 13 related to IEC 61076-3-106. Locking lever |
| I.S. EN 60512-29-100:2015 | CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 29-100: SIGNAL INTEGRITY TESTS UP TO 500 MHZ ON M12 STYLE CONNECTORS - TESTS 29A TO 29G |
| I.S. EN 60512-28-100:2013 | CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 28-100: SIGNAL INTEGRITY TESTS UP TO 1000 MHZ ON IEC 60603-7 AND IEC 61076-3 SERIES CONNECTORS - TESTS 28A TO 28G (IEC 60512-28-100:2013(EQV)) |
| I.S. EN 61076-3-115:2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-115: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR PROTECTIVE HOUSINGS FOR USE WITH 8-WAY SHIELDED AND UNSHIELDED CONNECTORS FOR FREQUENCIES UP TO 600 MHZ FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE - VARIANT 12 RELATED TO IEC 61076-3-106 - PUSH-PULL TYPE |
| I.S. EN 61076-3-106:2006 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-106: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR PROTECTIVE HOUSINGS FOR USE WITH 8-WAY SHIELDED AND UNSHIELDED CONNECTORS FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE |
| I.S. EN 61076-2:2011 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2: SECTIONAL SPECIFICATION FOR CIRCULAR CONNECTORS |
| CEI EN 61076-3-001 : 2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-001: RECTANGULAR CONNECTORS - BLANK DETAIL SPECIFICATION |
| EN 60603-7:2009/A1:2011 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS (IEC 60603-7:2008/A1:2011) |
| I.S. EN 61076-2-106:2011 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-106: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR CONNECTORS M 16 X 0,75 WITH SCREW-LOCKING AND DEGREE OF PROTECTION IP40 OR IP65/67 |
| I.S. EN 61076-3-118:2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-118: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR A 4 POLE + PE POWER CONNECTOR WITH PUSH-PULL COUPLING |
| BS EN 61076-3-110:2016 | Connectors for electronic equipment. Product requirements Detail specification for free and fixed connectors for data transmission with frequencies up to 3 000 MHz |
| EN 61076-3-122:2017 | Connectors for electrical and electronic equipment - Product requirements - Part 3-122: Detail specification for 8-way, shielded, free and fixed connectors for I/O and Gigabit Ethernet applications in harsh environments |
| CEI EN 61076-2-107 : 2011 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-107: DETAIL SPECIFICATION FOR CIRCULAR HYBRID CONNECTORS M12 WITH ELECTRICAL AND FIBRE-OPTIC CONTACTS WITH SCREW LOCKING |
| CEI EN 61076-3-118 : 2011 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-118: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR A 4 POLE + PE POWER CONNECTOR WITH PUSH-PULL COUPLING |
| CEI EN 61076-4-100 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-100: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES HAVING A GRID OF 2,5 MM FOR PRINTED BOARDS AND BACKPLANES |
| CEI EN 62197-1 : 2007 | CONNECTORS FOR ELECTRONIC EQUIPMENT - QUALITY ASSESSMENT REQUIREMENTS - PART 1: GENERIC SPECIFICATION |
| BS EN 61076-7-001:2004 | Connectors for electronic equipment Cable outlet accessories - Blank detail specification |
| CEI EN 61076-4 : 1997 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: SECTIONAL SPECIFICATION PRINTED BOARD CONNECTORS |
| CEI EN 61076-4-114 : 2004 | CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-114: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION HAVING A GRID OF 1 MM X 1,5 MM |
| BS EN 61076-3:2008 | Connectors for electronic equipment. Product requirements Rectangular connectors. Sectional specification |
| BS EN 61076-3-118:2010 | Connectors for electronic equipment. Product requirements Rectangular connectors. Detail specification for a 4 pole + PE power connector with push-pull coupling |
| BS EN 61076-2:2011 | Connectors for electronic equipment. Product requirements Sectional specification for circular connectors |
| BS EN 61076-3-114:2009 | Connectors for electronic equipment. Product requirements Rectangular connectors. Detail specification for.protective housings for use with 8-way shielded and unshielded connectors for frequencies up to 600 MHz for industrial environments incorporating the IEC 60603-7 series interface. Variant 11 related to IEC 61076-3-106. Bayonet coupling type |
| CEI EN 61076-4-108 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT PART 4-108: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY DETAIL SPECIFICATION FOR CABLE-TO-BOARD CONNECTORS, WITH A MODULAR PITCH OF 25 MM AND INTEGRATED SHIELDING FUNCTION, APPLICABLE FOR TRANSVERSE PACKING DENSITY OF 15 MM, HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1 |
| I.S. EN 61076-7-001:2004 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7-001: CABLE OUTLET ACCESSORIES - BLANK DETAIL SPECIFICATION |
| I.S. EN 61076-4-113:2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRINTED BOARD CONNECTORS - PART 4-113: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS HAVING 5 ROWS WITH A GRID OF 2,54 MM FOR PRINTED BOARDS AND BACKPLANES IN BUS APPLICATIONS |
| CEI EN 61076-3-115 : 2012 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-115: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR PROTECTIVE HOUSINGS FOR USE WITH 8-WAY SHIELDED AND UNSHIELDED CONNECTORS FOR FREQUENCIES UP TO 600 MHZ FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE - VARIANT 12 RELATED TO IEC 61076-3-106 - PUSH-PULL TYPE |
| BS EN 60603-7 : 2009 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS |
| I.S. EN 61076-4-111:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRINTED BOARD CONNECTORS WITH ASSESSED QUALIFY - DETAIL SPECIFICATION FOR TWO-PART POWER CONNECTOR MODULES, FOR PRINTED BOARDS AND BACKPLANES HAVING EARLY MATING FEATURES, AND HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1 |
| BS EN 175301-801:2006 | Detail specification. High density rectangular connectors, round removable crimp contacts |
| BS EN 61076-3-120:2016 | Connectors for electronic equipment. Product requirements Rectangular connectors. Detail specification for rewirable power connectors with snap locking for rated voltage of 250 V d.c. and rated current of 30 A |
| BS EN 61076-2-109:2014 | Connectors for electronic equipment. Product requirements Circular connectors. Detail specification for connectors with M 12 × 1 screw-locking, for data transmission frequencies up to 500 MHz |
| BS EN 61076-4-105:1998 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for 9 mm circular connector with 3 to 8 contacts for use in a wide range of applications including the telecommunication and audio industry |
| I.S. EN 61076-2-107:2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-107: DETAIL SPECIFICATION FOR CIRCULAR HYBRID CONNECTORS M12 WITH ELECTRICAL AND FIBRE-OPTIC CONTACTS WITH SCREW LOCKING |
| EN IEC 61076-2-111:2018 | Connectors for electrical and electronic equipment - Product requirements - Part 2-111: Circular connectors - Detail specification for power connectors with M12 screw-locking |
| NF EN 61076 4 001 : 1997 | CONNECTORS WITH ASSESSED QUALITY, FOR USED IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PRINTED BOARD CONNECTORS - BLANK DETAIL SPECIFICATION |
| NF EN 61076 4 101 : 2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-101: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES, HAVING A BASIC GRID OF 2,0 MM FOR PRINTED BOARDS AND BLACKPLANES IN ACCORDANCE WITH IEC 60917 |
| CEI EN 61076-2-001 : 2012 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-001: CIRCULAR CONNECTORS - BLANK DETAIL SPECIFICATION |
| CEI EN 61076-2 : 2012 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2: SECTIONAL SPECIFICATION FOR CIRCULAR CONNECTORS |
| BS EN 61076-2-101:2012 | Connectors for electronic equipment. Product requirements Circular connectors. Detail specification for M12 connectors with screw-locking |
| I.S. EN 61076-2-109:2014 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-109: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR CONNECTORS WITH M 12 X 1 SCREW-LOCKING, FOR DATA TRANSMISSION FREQUENCIES UP TO 500 MHZ |
| I.S. EN 61076-4-102:1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 102: DETAIL SPECIFICATION FOR TWO-PART SINGLE-POLE CONNECTORS, FOR MULTIPLE USES ON PLUG-IN UNITS, WITH PRE-CENTRING, CODING AND EARLY MATING FEATURES, HAVING A METRIC GRID IN ACCORDANCE WITH IEC 60917 |
| I.S. EN 175301-801:2006 | DETAIL SPECIFICATION: HIGH DENSITY RECTANGULAR CONNECTORS, ROUND REMOVABLE CRIMP CONTACTS |
| CEI EN 61076-6 : 2004 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 6: LOOSE PART CONTACTS - SECTIONAL SPECIFICATION |
| CEI EN 61076-4-001 : 1997 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 001: BLANK DETAIL SPECIFICATION |
| CEI EN 61076-2-105 : 2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-105: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR M5 CONNECTORS WITH SCREW-LOCKING |
| NF EN 61076 3 101 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTER-LINE |
| I.S. EN 61076-3-104:2017 | CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-104: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED FREE AND FIXED CONNECTORS FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 2000 MHZ |
| EN 60512-28-100:2013 | Connectors for electronic equipment - Tests and measurements - Part 28-100: Signal integrity tests up to 1 000 MHz on IEC 60603-7 and IEC 61076-3 series connectors - Tests 28a to 28g |
| EN 61076-4:1996 | Connectors with assessed quality, for use in d.c., low frequency analogue and in digital high-speed data applications - Part 4: Sectional specification - Printed board connectors |
| CEI EN 61076-4-103 : 2001 | CONNECTORS FOR USE IN D.C. LOW - FREQUENCY ANALOGUE AND DIGITAL HIGH SPEED DATA APPLICATIONS PART 4-103: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH SHIELDING AND A BASIC GRID OF 2,5 MM |
| BS EN 61076-2-102:2002 | Connectors for electronic equipment. Circular connectors Circular connectors with assessed quality. Detail specification for plugs and jacks for external low voltage power supply |
| CEI EN 61076-2-113 : 1ED 2017 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-113: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR CONNECTORS WITH M12 SCREW LOCKING WITH POWER AND SIGNAL CONTACTS FOR DATA TRANSMISSION WITH FREQUENCY UP TO 100 MHZ |
| CEI EN 61076-3-101 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D/C/ LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTRE-LINE |
| CEI EN 60512-28-100 : 2014 | CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 28-100: SIGNAL INTEGRITY TESTS UP TO 1000 MHZ ON 60603-7 AND 61076-3 SERIES CONNECTORS - TESTS 28A TO 28G |
| I.S. EN 61076-4-115:2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-115: PRINTED BOARD CONNECTORS - BACKPLANE CONNECTOR FOR INFINIBAND EQUIPMENT |
| I.S. EN 61076-2-101:2012 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-101: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR M12 CONNECTORS WITH SCREW-LOCKING (IEC 61076-2-101:2012 (EQV)) |
| EN IEC 61076-3-119:2018 | Connectors for electrical and electronic equipment - Product requirements - Part 3-119: Rectangular connectors - Detail specification for shielded and unshielded, free and fixed 10-way connectors with push-pull coupling for industrial environments for data transmission with frequencies up to 100 MHz |
| CEI EN 61076-3-122 : 1ED 2017 | CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-122: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS FOR I/O AND GIGABIT ETHERNET APPLICATIONS IN HARSH ENVIRONMENTS |
| BS EN 175301-803:2006 | Detail specification: rectangular connectors. Flat contacts, 0,8 mm thickness, locking screw not detachable |
| NF EN 61076 4 105 : 1999 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 105: DETAIL SPECIFICATION FOR 9 MM CIRCULAR CONNECTOR WITH 3 TO 8 CONTACTS FOR USE IN A WIDE RANGE OF APPLICATIONS INCLUDING THE TELECOMMUNICATION AND AUDIO INDUSTRY |
| BS EN 61076-3-117:2009 | Connectors for electronic equipment. Product requirements Rectangular connectors. Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface. Variant 14 related to IEC 61076-3-106. Push-pull coupling |
| BS EN 61076-4-108:2002 | Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for cable-to-board connectors, with a modular pitch of 25 mm and integrated shielding function, applicable for transverse packing density of 15 mm, having a basic grid of 2,5 mm in accordance with IEC 60917-1 |
| BS EN 60603-7-5:2010 | Connectors for electronic equipment Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 250 MHz |
| I.S. EN 61076-3-122:2017 | CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-122: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED, FREE AND FIXED CONNECTORS FOR I/O AND GIGABIT ETHERNET APPLICATIONS IN HARSH ENVIRONMENTS |
| I.S. EN 61076-4-001:1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 001: BLANK DETAIL SPECIFICATION |
| CEI EN 61076-3 : 2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3: RECTANGULAR CONNECTORS - SECTIONAL SPECIFICATION |
| I.S. EN 60603-7:2009 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS (IEC 60603-7:2008) |
| I.S. EN 61076-2-104:2014 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-104: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR CIRCULAR CONNECTORS WITH M8 SCREW-LOCKING OR SNAP-LOCKING |
| I.S. EN 61076-4-110:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION |
| I.S. EN 61076-4-104:1999 | CONNECTORS FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4-104: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART MODULAR CONNECTORS, BASIC GRID OF 2.0 MM WITH TERMINATIONS ON A MULTIPLE GRID OF 0.5 MM |
| I.S. EN 61076-3-110:2016 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-110: DETAIL SPECIFICATION FOR FREE AND FIXED CONNECTORS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 3000 MHZ |
| I.S. EN 61076-3-001:2008 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-001: RECTANGULAR CONNECTORS - BLANK DETAIL SPECIFICATION |
| IEC 61076-2-102:2002 | Connectors for electronic equipment - Part 2-102: Circular connectors with assessed quality - Detail specification for plugs and jacks for external low voltage power supply |
| EN 175301-803:2006 | Detail Specification: Rectangular connectors - Flat contacts, 0,8 mm thickness, locking screw not detachable |
| CEI EN 61076-2-101 : 2013 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-101: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR M12 CONNECTORS WITH SCREW-LOCKING |
| BS EN 60512-28-100:2013 | Connectors for electronic equipment. Tests and measurements Signal integrity tests up to 1000 MHz on IEC 60603-7 and IEC 61076-3 series connectors. Tests 28a to 28g |
| 04/30116868 DC : DRAFT JUL 2004 | EN 175301-803 - DETAIL SPECIFICATION - RECTANGULAR CONNECTORS - FLAT CONTACTS, 0,8 MM THICKNESS, LOCKING SCREW NOT DETACHABLE |
| I.S. EN 61076-4-114:2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-114: PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR WITH INTEGRATED SHIELDING FUNCTION HAVING A GRID OF 1 MM X 1,5 MM |
| CEI EN 61076-3-117 : 2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-117: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR PROTECTIVE HOUSINGS FOR USE WITH 8-WAY SHIELDED AND UNSHIELDED CONNECTORS FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE - VARIANT 14 RELATED TO IEC 61076-3-106 - PUSH PULL COUPLING |
| CEI EN 61076-3-110 : 2013 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-110: DETAIL SPECIFICATION FOR FREE AND FIXED CONNECTORS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 3000 MHZ |
| BS EN 61076-4-107:2001 | Connectors for electronic equipment Printed board connectors with assessed quality. Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations |
| CEI EN 61076-4-102 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS SECTION 102: DETAIL SPECIFICATION FOR TWO-PART SINGLE-POLE CONNECTORS, FOR MULTIPLE USES ON PLUG-IN UNITS, WITH PRE-CENTRING, CODING AND EARLY MATING FEATURES, HAVING A METRIC GRID IN ACCORDANCE WITH IEC 60917 |
| I.S. EN 61076-7-100:2006 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 7-100: CABLE OUTLET ACCESSORIES - DETAIL SPECIFICATION FOR A METRIC CABLE SEALING CONSISTING OF AN INTEGRATED PART OF HEAVY-DUTY RECTANGULAR OR CIRCULAR CONNECTOR HOODS AND A SEALING SYSTEM |
| BS EN 61076-2-113:2017 | Connectors for electronic equipment. Product requirements Circular connectors. Detail specification for connectors with M12 screw locking with power and signal contacts for data transmission with frequency up to 100 MHz |
| BS EN 61076-2-104:2014 | Connectors for electronic equipment. Product requirements Circular connectors. Detail specification for circular connectors with M8 screw-locking or snap-locking |
| CEI EN 175301-803 : 2007 | DETAIL SPECIFICATION: RECTANGULAR CONNECTORS - FLAT CONTACTS, 0,8 MM THICKNESS, LOCKING SCREW NOT DETACHABLE |
| BS EN 61076-3-104:2017 | Connectors for electrical and electronic equipment. Product requirements Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to 2 000 MHz |
| BS EN 62197-1:2006 | Connectors for electronic equipment. Quality assessment requirements Generic specification |
| BS EN 61076-3-001:2000 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Rectangular connectors Blank detail specification |
| BS EN 61076-4-100:2002 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for two-part connector modules having a grid of 2,5 mm for printed boards and backplanes |
| BS EN 61076-4-114:2003 | Connectors for electronic equipment. Printed board connectors with assessed quality Detail specification for two-part connector with integrated shielding function having a grid of 1 mm x 1,5 mm |
| CEI EN 175301-801 : 2007 | DETAIL SPECIFICATION: HIGH DENSITY RECTANGULAR CONNECTORS, ROUND REMOVABLE CRIMP CONTACTS |
| I.S. EN 61076-2-102:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 2-102: CIRCULAR CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR PLUGS AND JACKS FOR EXTERNAL LOW VOLTAGE POWER SUPPLY |
| I.S. EN 61076-3:2008 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3: RECTANGULAR CONNECTORS - SECTIONAL SPECIFICATION |
| I.S. EN IEC 61076-3-119:2018 | CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-119: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR SHIELDED AND UNSHIELDED, FREE AND FIXED 10-WAY CONNECTORS WITH PUSH-PULL COUPLING FOR INDUSTRIAL ENVIRONMENTS FOR DATA TRANSMISSION WITH FREQUENCIES UP TO 100 MHZ |
| I.S. EN IEC 61076-2-111:2018 | CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-111: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR POWER CONNECTORS WITH M12 SCREW-LOCKING |
| I.S. EN 61076-2-113:2017 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-113: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR CONNECTORS WITH M12 SCREW LOCKING WITH POWER AND SIGNAL CONTACTS FOR DATA TRANSMISSION WITH FREQUENCY UP TO 100 MHZ |
| CEI EN 61076-4-105 : 2001 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PRINTED BOARD CONNECTORS - DETAIL SPECIFICATION FOR 9 MM CIRCULAR CONNECTOR WITH 3 TO 8 CONTACTS FOR USE IN A WIDE RANGE OF APPLICATIONS INCLUDING THE TELECOMMUNICATION= AND AUDIO INDUSTRY |
| I.S. EN 61076-3-114:2009 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-114: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR PROTECTIVE HOUSINGS FOR USE WITH 8-WAY SHIELDED AND UNSHIELDED CONNECTORS FOR FREQUENCIES UP TO 600 MHZ FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE - VARIANT 11 RELATED TO IEC 61076-3-106 - BAYONET COUPLING TYPE |
| I.S. EN 62197-1:2006 | CONNECTORS FOR ELECTRONIC EQUIPMENT - QUALITY ASSESSMENT REQUIREMENTS - PART 1: GENERIC SPECIFICATION |
| I.S. EN 61076-4-108:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-108: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR CABLE-TO-BOARD CONNECTORS, WITH A MODULAR PITCH OF 25 MM AND INTEGRATED SHIELDING FUNCTION, APPLICABLE FOR TRANSVERSE PACKING DENSITY OF 15 MM, HAVING A BASIC GRID OF 2,5 MM IN ACCORDANCE WITH IEC 60917-1 |
| I.S. EN 61076-6:2004 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 6: LOOSE PART CONTACTS - SECTIONAL SPECIFICATION |
| EN 61076-3-104:2017 | Connectors for electrical and electronic equipment - Product requirements - Part 3-104: Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to 2 000 MHz |
| EN 61076-4-100:2001 | Connectors for electronic equipment - Part 4-100: Printed board connectors with assessed quality - Detail specification for two-part connector modules having a grid of 2,5 mm for printed boards and backplanes |
| EN 61076-4-115:2003 | Connectors for electronic equipment - Part 4-115: Printed board connectors - Backplane connector for InfiniBand equipment |
| EN 61076-2-101:2012 | Connectors for electronic equipment - Product requirements - Part 2-101: Circular connectors - Detail specification for M12 connectors with screw-locking |
| EN 61076-3-115:2010 | Connectors for electronic equipment - Product requirements - Part 3-115: Rectangular connectors - Detail specification for protective housings for use with 8-way shielded and unshielded connectors for frequencies up to 600 MHz for industrial environments incorporating the IEC 60603-7 series interface - Variant 12 related to IEC 61076-3-106 - Push-pull type |
| EN 61076-2-109:2014 | Connectors for electronic equipment - Product requirements - Part 2-109: Circular connectors - Detail specification for connectors with M 12 × 1 screw-locking, for data transmission frequencies up to 500 MHz |
| EN 61076-3-110:2016 | Connectors for electronic equipment - Product requirements - Part 3-110: Detail specification for free and fixed connectors for data transmission with frequencies up to 3 000 MHz |
| EN 61076-4-107:2001 | Connectors for electronic equipment - Part 4-107: Printed board connectors with assessed quality - Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations |
| EN 61076-3-001:2008 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-001: RECTANGULAR CONNECTORS - BLANK DETAIL SPECIFICATION |
| EN 61076-3-100:2000 | Connectors for use in d.c., low-frequency analogue and digital high speed data applications - Part 3-100: Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row |
| EN 61076-3:2008 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3: RECTANGULAR CONNECTORS - SECTIONAL SPECIFICATION |
| EN 61076-3-112 : 2006 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 3-112: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR RECTANGULAR CONNECTORS WITH FOUR CONTACTS FOR HIGH PERFORMANCE SERIAL BUS FOR CONSUMER AUDIO/VIDEO EQUIPMENT |
| EN 61076-3-117:2009 | Connectors for electronic equipment - Product requirements - Part 3-117: Rectangular connectors - Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface - Variant 14 related to IEC 61076-3-106 - Push pull coupling |
| EN 61076-2-102:2002 | Connectors for electronic equipment - Part 2-102: Circular connectors with assessed quality - Detail specification for plugs and jacks for external low voltage power supply |
| EN 61076-6 : 2004 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 6: LOOSE PART CONTACTS - SECTIONAL SPECIFICATION |
| EN 61076-2-107 : 2010 | Connectors for electronic equipment - Product requirements - Part 2-107: Detail specification for circular hybrid connectors M12 with electrical and fibre-optic contacts with screw locking |
| EN 61076-2-105:2008 | Connectors for electronic equipment - Product requirements - Part 2-105: Circular connectors - Detail specification for M5 connectors with screw-locking |
| EN 61076-4-104:1999 | Connectors for use in d.c. low-frequency analogue and digital high speed data applications - Part 4-104: Printed board connectors with assessed quality - Detail specification for two-part modular connectors, basic grid of 2,0 mm, with terminations on a multiple grid of 0,5 mm |
| EN 61076-3-106 : 2006 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-106: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR PROTECTIVE HOUSINGS FOR USE WITH 8-WAY SHIELDED AND UNSHIELDED CONNECTORS FOR INDUSTRIAL ENVIRONMENTS INCORPORATING THE IEC 60603-7 SERIES INTERFACE |
| EN 61076-3-120:2016 | Connectors for electronic equipment - Product requirements - Part 3-120: Rectangular connectors - Detail specification for rewirable power connectors with snap locking for rated voltage of 250 V d.c. and rated current of 30 A |
| EN 61076-3-103:2004 | Connectors for electronic equipment - Part 3-103: Rectangular connectors - Detail specification for single row connectors with non-removable ribbon cable contacts on 1,25 mm pitch used for high speed serial data (HSSDC) |
| EN 61076-2-001:2011 | Connectors for electronic equipment - Product requirements - Part 2-001: Circular connectors - Blank detail specification |
| EN 61076-3-118 : 2010 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-118: RECTANGULAR CONNECTORS - DETAIL SPECIFICATION FOR A 4 POLE + PE POWER CONNECTOR WITH PUSH-PULL COUPLING |
| IEC GUIDE 109:2012 | Environmental aspects - Inclusion in electrotechnical product standards |
| EN 20286-2 : 1993 | ISO SYSTEM OF LIMITS AND FITS - TABLES OF STANDARD TOLERANCE GRADES AND LIMIT DEVIATIONS FOR HOLES AND SHAFTS |
| IEC 61076-3:2008 | Connectors for electronic equipment - Product requirements - Part 3: Rectangular connectors - Sectional specification |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC TR 62225:2001 | Guidance on terms for connectors and mechanical structures in electronic equipment |
| EN ISO 1101:2017 | Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out (ISO 1101:2017) |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| EN ISO 1302:2002 | Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation (ISO 1302:2002) |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| IEC 61076-6:2004 | Connectors for electronic equipment - Part 6: Loose part contacts - Sectional specification |
| IEC 61076-7:2000 | Connectors for use in d.c., low-frequency analogue and digital high speed data applications - Part 7: Cable outlet accessories with assessed quality, including qualification and capability approval - Sectional specifiation |
| EN 20286-1 : 1993 | ISO SYSTEM OF LIMITS AND FITS - BASES OF TOLERANCES, DEVIATIONS AND FITS |
| ISO 1302:2002 | Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation |
| IEC 61076-5:2001 | Connectors for use in d.c., low-frequency analogue and digital high-speed data applications - Part 5: In-line sockets with assessed quality - Sectional specification |
| IEC 61076-4:1995 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high-speed data applications - Part 4: Sectional specification - Printed board connectors |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| IEC 61076-2:2011 | Connectors for electronic equipment - Product requirements - Part 2: Sectional specification for circular connectors |
| EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| ISO 129-1:2004 | Technical drawings Indication of dimensions and tolerances Part 1: General principles |
| EN 62197-1 : 2006 | CONNECTORS FOR ELECTRONIC EQUIPMENT - QUALITY ASSESSMENT REQUIREMENTS - PART 1: GENERIC SPECIFICATION |
| IEC 62197-1:2006 | Connectors for electronic equipment - Quality assessment requirements - Part 1: Generic specification |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 60050-581:2008 | International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.