EN 549:1994
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Rubber materials for seals and diaphragms for gas appliances and gas equipment
Superseded date
03-07-2019
Superseded by
Published date
22-11-1994
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1. Scope
2. Normative references
3. Definitions
4. Manufacturer's declared information
5. Classification
6. Requirements
7. Test methods
Annex
A. (normative) Verification of components by physical
and chemical testing
B. (normative) Verification of components by infra-red
spectrometric method
This standard specifies requirements and associated test methods for vulcanized rubber materials used in gas appliances and equipment in contact with 1st, 2nd and 3rd family combustible gases. It also establishes a classification based on temperature range and hardness. This standard is applicable to materials from which are manufactured homogeneous seals and homogeneous or reinforced diaphragms. The normal range of operating temperatures covered by this standard is 0 øC to + 60 øC. Tests are also included for applications using diaphragms within the range - 20 øC to + 80 øC and seals within the range - 20 øC to + 150 øC. For temperatures outside these ranges the user should contact the manufacturer regarding the suitability of the rubber material. This standard includes two normative annexes for the verification that a component (finished product) was produced from a previously type tested material complying with requirements of this standard as declared by the appliance or equipment manufacturer or supplier of the component. This standard is not applicable to silicone rubber used either above 200 mbar nominal pressure or at temperatures below 0 øC with 3rd family gases as there is possibility of condensation. This standard is also not applicable to seals and diaphragms for devices in gas transmission systems nor in such equipment used in 1st and 2nd family gas distribution systems.
| Committee |
CEN/TC 208
|
| DevelopmentNote |
Supersedes EN 278, EN 279 & EN 291. (08/2012)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DS EN 549 : 1995 | Identical |
| ONORM EN 549 : 1995 | Identical |
| DIN EN 549:1995-04 | Identical |
| I.S. EN 549:1995 | Identical |
| UNE-EN 549:1996 | Identical |
| NBN EN 549 : 1995 | Identical |
| NF EN 549 : 1995 | Identical |
| NS EN 549 : 1ED 1995 | Identical |
| PN EN 549 : 2000 | Identical |
| SN EN 549 : 1995 | Identical |
| NEN EN 549 : 1995 | Identical |
| BS EN 549:1995 | Identical |
| UNI EN 549 : 1996 | Identical |
| I.S. EN 16125:2015 | LPG EQUIPMENT AND ACCESSORIES - PIPEWORK SYSTEMS AND SUPPORTS - LPG IN LIQUID PHASE AND VAPOUR PRESSURE PHASE |
| EN 13175:2014 | LPG Equipment and accessories - Specification and testing for Liquefied Petroleum Gas (LPG) pressure vessel valves and fittings |
| 13/30281974 DC : 0 | BS EN 16617 - PIPEWORK - CORRUGATED METAL HOSE ASSEMBLIES FOR COMBUSTIBLE GAS - PERFORMANCE REQUIREMENTS, TESTING AND MARKING |
| 15/30320783 DC : 0 | BS EN 1439 - LPG EQUIPMENT AND ACCESSORIES - PROCEDURE FOR CHECKING TRANSPORTABLE REFILLABLE LPG CYLINDERS BEFORE, DURING AND AFTER FILLING |
| DIN EN 1254-8:2012-12 | Copper and copper alloys - Plumbing fittings - Part 8: Fittings with press ends for use with plastics and multilayer pipes |
| DIN EN 14829:2007-11 | Independent gas-fired flueless space heaters for nominal heat input not exceeding 6 kW |
| I.S. EN 13152:2002 | SPECIFICATION AND TESTING OF LPG CYLINDER VALVES - SELF CLOSING |
| 02/711303 DC : DRAFT SEP 2002 | PREN 14543 - SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PATIO HEATERS - LPG FLUELESS PATIO HEATERS FOR OUTDOOR AND VENTILATED AREA USE |
| 13/30279702 DC : 0 | BS EN 331 - MANUALLY OPERATED BALL VALVES AND CLOSED BOTTOM TAPER PLUG VALVES FOR GAS INSTALLATIONS FOR BUILDINGS |
| 12/30254959 DC : 0 | BS EN 89 - GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| DIN EN ISO 15995:2010-11 | GAS CYLINDERS - SPECIFICATIONS AND TESTING OF LPG CYLINDER VALVES - MANUALLY OPERATED |
| ONORM EN 521 : 2006 | SPECIFICATIONS FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PORTABLE VAPOUR PRESSURE LIQUEFIED PETROLEUM GAS APPLIANCES |
| EN ISO 15995:2010 | Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated (ISO 15995:2006) |
| 99/718298 DC : DRAFT DEC 1999 | PREN 13785 - REGULATORS WITH A CAPACITY OF UP TO AND INCLUDING 100KGH |
| PREN 14141 : DRAFT 2011 | VALVES FOR NATURAL GAS TRANSPORTATION IN PIPELINES - PERFORMANCE REQUIREMENTS AND TESTS |
| PREN 14129 : DRAFT 2011 | LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR LPG TANKS |
| 01/706620 DC : DRAFT APR 2001 | PREN 14129 - PRESSURE RELIEF VALVES FOR LPG TANKS |
| BS EN 16617:2015 | Pipework. Corrugated metal hose assemblies for combustible gas. Performance requirements, testing and marking |
| BS EN ISO 14245:2010 | Gas cylinders. Specifications and testing of LPG cylinder valves. Self-closing |
| DIN EN 16617:2015-07 | PIPEWORK - CORRUGATED METAL HOSE ASSEMBLIES FOR COMBUSTIBLE GAS - PERFORMANCE REQUIREMENTS, TESTING AND MARKING |
| 10/30227668 DC : 0 | BS EN 14678-3 - LPG EQUIPMENT AND ACCESSORIES - PART 3: REFUELLING INSTALLATIONS AT PRIVATE AND INDUSTRIAL PREMISES |
| 10/30227671 DC : 0 | BS EN 14678-1 - LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS |
| I.S. EN ISO 14245:2010 | GAS CYLINDERS - SPECIFICATIONS AND TESTING OF LPG CYLINDER VALVES - SELF-CLOSING |
| 12/30250279 DC : 0 | BS EN 12252 - LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS |
| 13/30287842 DC : 0 | BS EN 14543 - SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PARASOL PATIO HEATERS - FLUELESS RADIANT HEATERS FOR OUTDOOR OR AMPLY VENTILATED AREA USE |
| BS EN 15069:2008 | Safety gas connection valves for metal hose assemblies used for the connection of domestic appliances using gaseous fuel |
| 09/30202307 DC : 0 | BS EN 12514-1 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 1: SAFETY REQUIREMENTS AND TESTS - TERMINOLOGY, GENERAL REQUIREMENTS |
| I.S. EN 14678-3:2013 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 3: REFUELLING INSTALLATIONS AT COMMERCIAL AND INDUSTRIAL PREMISES |
| PREN 624 : DRAFT 2009 | SPECIFICATION FOR DEDICATED LPG APPLIANCES - ROOM SEALED LPG SPACE HEATING EQUIPMENT FOR INSTALLATION IN VEHICLES AND BOATS |
| UNI EN 13175 : 2015 | LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSEL VALVES AND FITTINGS |
| I.S. EN 13175:2014 | LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSEL VALVES AND FITTINGS |
| PREN 54-7 : DRAFT 2015 | FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 7: SMOKE DETECTORS - POINT DETECTORS USING SCATTERED LIGHT, TRANSMITTED LIGHT OR IONISATION |
| UNE-EN 16678:2016 | Safety and control devices for gas burners and gas burning appliances - Automatic shut-off valves for operating pressure of above 500 kPa up to and including 6 300 kPa |
| 16/30334287 DC : 0 | BS EN 334 - GAS PRESSURE REGULATORS FOR INLET PRESSURE UP TO 100 BAR |
| UNE-EN 16119:2013 | LPG equipment and accessories - Sealing caps and plugs for LPG cylinder and pressure vessel valves - Specification and testing |
| BS EN 521:2006 | Specifications for dedicated liquefied petroleum gas appliances. Portable vapour pressure liquefied petroleum gas appliances |
| EN 15202:2012 | LPG equipment and accessories - Essential operational dimensions for LPG cylinder valve outlet and associated equipment connections |
| I.S. EN 15202:2012 | LPG EQUIPMENT AND ACCESSORIES - ESSENTIAL OPERATIONAL DIMENSIONS FOR LPG CYLINDER VALVE OUTLET AND ASSOCIATED EQUIPMENT CONNECTIONS |
| DIN EN 26:2015-08 | Gas-fired instantaneous water heaters for the production of domestic hot water |
| DIN EN 14678-2:2012-04 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 2: Components other than dispensers and installation requirements (includes Amendment A1:2012) |
| BS EN 13785 : 2005 | REGULATORS WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, HAVING A MAXIMUM NOMINAL OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR, OTHER THAN THOSE COVERED BY EN 12864 AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| BS EN 14141:2013 | Valves for natural gas transportation in pipelines. Performance requirements and tests |
| BS EN 449 : 2002 | SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - DOMESTIC FLUELESS SPACE HEATERS (INCLUDING DIFFUSIVE CATALYTIC COMBUSTION HEATERS) |
| BS EN 15266:2007 | Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar |
| BS EN 624:2011 | Specification for dedicated LPG appliances. Room sealed LPG space heating equipment for installation in vehicles and boats |
| BS EN 12806:2003 | Automotive liquefied petroleum gas components. Other than containers |
| BS EN 13786 : 2004 | AUTOMATIC CHANGE-OVER VALVES HAVING A MAXIMUM OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| UNE-EN 331:2016 | Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings |
| DIN EN 14893:2014-09 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| BS EN 14678-2 : 2007 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS AND INSTALLATION REQUIREMENTS |
| BS EN 15202:2012 | LPG equipment and accessories. Essential operational dimensions for LPG cylinder valve outlet and associated equipment connections |
| BS EN 88-2:2007 | Pressure regulators and associated safety devices for gas appliances Pressure regulators for inlet pressures above 500 mbar up to and including 5 bar |
| BS EN 13760:2003 | Automotive LPG filling system for light and heavy duty vehicles. Nozzle, test requirements and dimensions |
| I.S. EN 14678-2:2007 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS AND INSTALLATION REQUIREMENTS |
| DIN EN 13152:2003-09 | SPECIFICATION AND TESTING OF LPG CYLINDER VALVES - SELF-CLOSING |
| I.S. EN 89:2015 | GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| DIN EN 13787:2002-04 | ELASTOMERS FOR GAS PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR INLET PRESSURES UP TO 100 BAR |
| DIN EN 15033:2007-02 | Room sealed storage water heaters for the production of sanitary hot water using LPG for vehicles and boats |
| EN 16129:2013 | Pressure regulators, automatic change-over devices, having a maximum regulated pressure of 4 bar, with a maximum capacity of 150 kg/h, associated safety devices and adaptors for butane, propane, and their mixtures |
| DIN EN 1439:2017-10 | LPG equipment and accessories - Procedure for checking transportable refillable LPG cylinders before, during and after filling |
| DIN EN 14800:2007-06 | Corrugated safety metal hose assemblies for the connection of domestic appliances using gaseous fuels |
| DIN EN 14543:2017-10 | SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PARASOL PATIO HEATERS - FLUELESS RADIANT HEATERS FOR OUTDOOR OR AMPLY VENTILATED AREA USE |
| EN 13153 : 2001 AMD 1 2003 | SPECIFICATION AND TESTING OF LPG CYLINDER VALVES - MANUALLY OPERATED |
| EN 30-1-1:2008+A3:2013 | Domestic cooking appliances burning gas - Part 1-1: Safety - General |
| I.S. EN 13760:2003 | AUTOMOTIVE LPG FILLING SYSTEM FOR LIGHT AND HEAVY DUTY VEHICLES - NOZZLE, TEST REQUIREMENTS AND DIMENSIONS |
| EN 12806:2003 | Automotive liquefied petroleum gas components - Other than containers |
| EN 1439:2017 | LPG equipment and accessories - Procedure for checking transportable refillable LPG cylinders before, during and after filling |
| DIN EN 521:2006-05 | SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PORTABLE VAPOUR PRESSURE LIQUEFIED PETROLEUM GAS APPLIANCES |
| PREN 14543 : DRAFT 2013 | SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PARASOL PATIO HEATERS - FLUELESS RADIANT HEATERS FOR OUTDOOR OR AMPLY VENTILATED AREA USE |
| PREN 13774 : DRAFT 2011 | VALVES FOR GAS DISTRIBUTION SYSTEMS WITH MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 16 BAR - PERFORMANCE REQUIREMENTS |
| DIN EN 16119:2013-05 | LPG equipment and accessories - Sealing caps and plugs for LPG cylinder and pressure vessel valves - Specification and testing |
| 05/30135987 DC : 0 | EN 161 - AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES |
| DIN EN ISO 14245:2010-11 | GAS CYLINDERS - SPECIFICATIONS AND TESTING OF LPG CYLINDER VALVES - SELF-CLOSING |
| DIN EN 14678-3:2013-03 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 3: REFUELLING INSTALLATIONS AT COMMERCIAL AND INDUSTRIAL PREMISES |
| 13/30286091 DC : 0 | BS EN 16678 - SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - AUTOMATIC SHUT-OFF VALVES FOR OPERATING PRESSURE OF ABOVE 500 KPA UP TO AND INCLUDING 6300 KPA |
| I.S. EN 483:2000 | GAS-FIRED CENTRAL HEATING BOILERS - TYPE C BOILERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW |
| 99/716445 DC : DRAFT NOV 99 | AUTOMOTIVE LPG FILLING SYSTEM - PART 1: DIMENSIONS AND TEST REQUIREMENTS FOR THE CONNECTOR |
| I.S. EN 12864:2001 | LOW-PRESSURE, NON-ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| 08/30167437 DC : DRAFT JAN 2008 | BS EN ISO 28622 - PRESSURE RELIEF VALVES FOR TRANSPORTABLE REFILLABLE CYLINDERS FOR LIQUEFIED PETROLEUM GAS (LPG) |
| 13/30248693 DC : 0 | BS EN 14893 - LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| 12/30265334 DC : 0 | BS EN 13953 - LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR TRANSPORTABLE REFILLABLE CYLINDERS FOR LIQUEFIED PETROLEUM GAS (LPG) |
| 06/30148043 DC : 0 | EN 88-2 - PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 2: PRESSURE REGULATORS FOR INLET PRESSURES ABOVE 500 MBAR UP TO AND INCLUDING 5 BAR |
| PREN 16129 : DRAFT 2010 | PRESSURE REGULATORS, AUTOMATIC CHANGE-OVER DEVICES, HAVING A MAXIMUM REGULATED PRESSURE OF 4 BAR, WITH A MAXIMUM CAPACITY OF 100 KG/H, ASSOCIATED SAFETY DEVICES AND ADAPTORS FOR BUTANE, PROPANE, AND THEIR MIXTURES |
| 11/30248684 DC : 0 | BS EN 14129 - LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR LPG TANKS |
| 04/30126871 DC : DRAFT DEC 2004 | ISO 17484-1 - PLASTICS PIPING SYSTEMS - MULTI-LAYERED PIPE SYSTEMS FOR INDOOR GAS INSTALLATIONS WITH A MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 5 BAR - PART 1: SPECIFICATIONS FOR SYSTEMS |
| 05/30125032 DC : DRAFT JUL 2005 | EN 14678-2 - LPG EQUIPMENT AND ACCESSORIES - EQUIPMENT FOR LIQUEFIED PETROLEUM GAS AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS, AND INSTALLATION REQUIREMENTS |
| 17/30362705 DC : 0 | BS EN 15202 - LPG EQUIPMENT AND ACCESSORIES - ESSENTIAL OPERATIONAL DIMENSIONS FOR LPG CYLINDER VALVE OUTLET AND ASSOCIATED EQUIPMENT CONNECTIONS |
| BS EN 14678-3:2013 | LPG equipment and accessories. Construction and performance of LPG equipment for automotive filling stations Refuelling installations at commercial and industrial premises |
| BS EN 1254-8:2012 | Copper and copper alloys. Plumbing fittings Fittings with press ends for use with plastics and multilayer pipes |
| UNI EN 16119 : 2013 | LPG EQUIPMENT AND ACCESSORIES - SEALING CAPS AND PLUGS FOR LPG CYLINDER AND PRESSURE VESSEL VALVES - SPECIFICATION AND TESTING |
| 05/30136930 DC : DRAFT JUL 2005 | EN 521 - SPECIFICATIONS FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PORTABLE VAPOUR PRESSURE LIQUEFIED PETROLEUM GAS APPLIANCES |
| 00/717229 DC : DRAFT NOV 2000 | PREN 14071 - PRESSURE RELIEF VALVES FOR LPG TANKS - ANCILLARY EQUIPMENT |
| PREN 89 : DRAFT 2012 | GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| BS EN 50465:2015 | European product standard for combined heating power systems using gas fuel |
| DIN EN 14893 E : 2014 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| ISO 15995:2006 | Gas cylinders Specifications and testing of LPG cylinder valves Manually operated |
| I.S. EN 14071:2015 | LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR LPG PRESSURE VESSELS - ANCILLARY EQUIPMENT |
| I.S. EN 16617:2015 | PIPEWORK - CORRUGATED METAL HOSE ASSEMBLIES FOR COMBUSTIBLE GAS - PERFORMANCE REQUIREMENTS, TESTING AND MARKING |
| BS EN 13175:2014 | LPG Equipment and accessories. Specification and testing for Liquefied Petroleum Gas (LPG) pressure vessel valves and fittings |
| PREN 30-1-1 : DRAFT 2017 | DOMESTIC COOKING APPLIANCES BURNING GAS - PART 1-1: SAFETY - GENERAL |
| I.S. EN 14829:2007 | INDEPENDENT GAS-FIRED FLUELESS SPACE HEATERS FOR NOMINAL HEAT INPUT NOT EXCEEDING 6 KW |
| UNE-EN 14678-2:2009 | LPG equipment and accessories - Equipment for Liquefied Petroleum Gas automotive filling stations - Part 2: Components other than dispensers, and installation requirements |
| UNE-EN 14071:2015 | LPG equipment and accessories - Pressure relief valves for LPG pressure vessels - Ancillary equipment |
| PREN 50465 : DRAFT 2011 | GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| BS EN 14071:2015 | LPG equipment and accessories. Pressure relief valves for LPG pressure vessels. Ancillary equipment |
| EN 50465 : 2015 | GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| EN 521:2006 | Specifications for dedicated liquefied petroleum gas appliances - Portable vapour pressure liquefied petroleum gas appliances |
| EN 14071:2015 | LPG equipment and accessories - Pressure relief valves for LPG pressure vessels - Ancillary equipment |
| I.S. EN 50465:2015 | GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| DIN EN 12252:2014-07 | LPG equipment and accessories - Equipping of LPG road tankers |
| DIN EN 1359:2007-06 | GAS METERS - DIAPHRAGM GAS METERS |
| DIN EN 12864:2006-03 | LOW-PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| DIN EN 89:2015-08 | GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| DIN EN 15266:2007-08 | Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar |
| BS EN 26:1998 | Gas fired instantaneous water heaters for the production of domestic hot water, fitted with atmospheric burners |
| UNE-EN 13799:2012 | LPG equipment and accessories - Contents gauges for Liquefied Petroleum Gas (LPG) pressure vessels |
| 17/30362889 DC : 0 | BS EN 13175 - LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSEL VALVES AND FITTINGS |
| 04/30124785 DC : 0 | EN 15069 - SAFETY GAS CONNECTION VALVES FOR METAL HOSE ASSEMBLIES USED FOR THE CONNECTION OF DOMESTIC APPLIANCES USING GASEOUS FUEL |
| UNE-EN 14141:2014 | Valves for natural gas transportation in pipelines - Performance requirements and tests |
| I.S. EN 624:2011 | SPECIFICATION FOR DEDICATED LPG APPLIANCES - ROOM SEALED LPG SPACE HEATING EQUIPMENT FOR INSTALLATION IN VEHICLES AND BOATS |
| I.S. EN 30-1-1:2008 | DOMESTIC COOKING APPLIANCES BURNING GAS - PART 1-1: SAFETY - GENERAL |
| I.S. EN 14678-1:2013 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS |
| EN 13953:2015 | LPG equipment and accessories - Pressure relief valves for transportable refillable cylinders for Liquefied Petroleum Gas (LPG) |
| DIN EN 12864 E : 2006 AMD 3 2010 | LOW PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| I.S. EN 13774:2013 | VALVES FOR GAS DISTRIBUTION SYSTEMS WITH MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 16 BAR - PERFORMANCE REQUIREMENTS |
| DIN EN 13153:2003-09 | SPECIFICATION AND TESTING OF LPG CYLINDER VALVES - MANUALLY OPERATED |
| I.S. EN 13953:2015 | LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR TRANSPORTABLE REFILLABLE CYLINDERS FOR LIQUEFIED PETROLEUM GAS (LPG) |
| I.S. EN 13799:2012 | LPG EQUIPMENT AND ACCESSORIES - CONTENTS GAUGES FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSELS |
| I.S. EN 449:2002 | SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - DOMESTIC FLUELESS SPACE HEATERS (INCLUDING DIFFUSIVE CATALYTIC COMBUSTION HEATERS) |
| I.S. EN 14129:2014 | LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR LPG PRESSURE VESSELS |
| DIN EN 13611:2019-06 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements |
| I.S. EN 331:2015 | MANUALLY OPERATED BALL VALVES AND CLOSED BOTTOM TAPER PLUG VALVES FOR GAS INSTALLATIONS FOR BUILDINGS |
| I.S. EN 14543:2017 | SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PARASOL PATIO HEATERS - FLUELESS RADIANT HEATERS FOR OUTDOOR OR AMPLY VENTILATED AREA USE |
| I.S. EN 26:2015 | GAS-FIRED INSTANTANEOUS WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| I.S. EN 1359:2017 | GAS METERS - DIAPHRAGM GAS METERS |
| DIN EN 12252:2000-10 | LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS |
| I.S. EN 14141:2013 | VALVES FOR NATURAL GAS TRANSPORTATION IN PIPELINES - PERFORMANCE REQUIREMENTS AND TESTS |
| I.S. EN 13787:2002 | ELASTOMERS FOR GAS PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR INLET PRESSURES UP TO 100 BAR |
| I.S. EN 14893:2014 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| I.S. EN 12252:2014 | LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS |
| DIN EN 13760:2003-11 | Automotive LPG filling system for light and heavy duty vehicles - Nozzle; Test requirements and dimensions |
| I.S. EN 88-2:2007 | PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 2: PRESSURE REGULATORS FOR INLET PRESSURES ABOVE 500 MBAR UP TO AND INCLUDING 5 BAR |
| I.S. EN 12806:2003 | AUTOMOTIVE LIQUEFIED PETROLEUM GAS COMPONENTS - OTHER THAN CONTAINERS |
| PREN 13953 : DRAFT 2012 | LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR TRANSPORTABLE REFILLABLE CYLINDERS FOR LIQUEFIED PETROLEUM GAS (LPG) |
| PREN 521 : DRAFT 2016 | SPECIFICATIONS FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PORTABLE VAPOUR PRESSURE LIQUEFIED PETROLEUM GAS APPLIANCES |
| 04/30124766 DC : DRAFT NOV 2004 | EN 15033 - ROOM SEALED STORAGE WATER HEATERS FOR THE PRODUCTION OF SANITARY HOT WATER USING LPG VEHICLES AND BOATS |
| 10/30228056 DC : 0 | |
| EN ISO 14245:2010 | Gas cylinders - Specifications and testing of LPG cylinder valves - Self-closing (ISO 14245:2006) |
| 10/30218988 DC : 0 | BS EN 13175 - LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) TANK VALVES AND FITTINGS |
| BS EN 14829:2007 | Independent gas-fired flueless space heaters for nominal heat input not exceeding 6 kW |
| 14/30304116 DC : 0 | BS EN 1359 - GAS METERS - DIAPHRAGM GAS METERS |
| 09/30205570 DC : 0 | BS EN 13799 - LPG EQUIPMENT AND ACCESSORIES - CONTENTS GAUGES FOR LPG TANKS |
| BS EN ISO 15995:2010 | Gas cylinders. Specifications and testing of LPG cylinder valves. Manually operated |
| PREN 1439 : DRAFT 2015 | LPG EQUIPMENT AND ACCESSORIES - PROCEDURE FOR CHECKING TRANSPORTABLE REFILLABLE LPG CYLINDERS BEFORE, DURING AND AFTER FILLING |
| 10/30231853 DC : DRAFT SEP 2010 | BS EN 10352 - STAINLESS STEEL PLUMBING FITTINGS - FITTINGS WITH PRESS ENDS FOR METALLIC TUBES |
| 07/30163618 DC : 0 | BS EN 1254-2 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 2: FITTINGS WITH COMPRESSION ENDS FOR USE WITH COPPER TUBES |
| 11/30213590 DC : 0 | BS EN 1254-8 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 8: FITTINGS WITH PRESS ENDS FOR USE WITH PLASTICS AND MULTILAYER PIPES |
| UNI EN 1254-8 : 2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 8: FITTINGS WITH PRESS ENDS FOR USE WITH PLASTICS AND MULTILAYER PIPES |
| UNE-EN 16129:2014 | Pressure regulators, automatic change-over devices, having a maximum regulated pressure of 4 bar, with a maximum capacity of 150 kg/h, associated safety devices and adaptors for butane, propane, and their mixtures |
| 15/30325369 DC : 0 | BS EN 484 - SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - INDEPENDENT STOVES, INCLUDING THOSE INCORPORATING A GRILL FOR OUTDOOR USE |
| PREN 26 : DRAFT 2012 | GAS-FIRED INSTANTANEOUS WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| ISO 14245:2006 | Gas cylinders Specifications and testing of LPG cylinder valves Self-closing |
| UNI EN 14678-3 : 2013 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 3: REFUELLING INSTALLATIONS AT COMMERCIAL AND INDUSTRIAL PREMISES |
| PREN 1359 : DRAFT 2014 | GAS METERS - DIAPHRAGM GAS METERS |
| DIN EN 521:2016-03 (Draft) | SPECIFICATIONS FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PORTABLE VAPOUR PRESSURE LIQUEFIED PETROLEUM GAS APPLIANCES |
| I.S. EN 13611:2015 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| DIN EN 14141:2013-08 | VALVES FOR NATURAL GAS TRANSPORTATION IN PIPELINES - PERFORMANCE REQUIREMENTS AND TESTS |
| DIN EN 331:2016-04 | MANUALLY OPERATED BALL VALVES AND CLOSED BOTTOM TAPER PLUG VALVES FOR GAS INSTALLATIONS FOR BUILDINGS |
| DIN EN 13786:2010-07 | AUTOMATIC CHANGE-OVER VALVES HAVING A MAXIMUM OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| DIN EN 13785:2010-05 | REGULATORS WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, HAVING A MAXIMUM NOMINAL OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR, OTHER THAN THOSE COVERED BY EN 12864 AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| DIN EN 14543:2013-11 (Draft) | SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PARASOL PATIO HEATERS - FLUELESS RADIANT HEATERS FOR OUTDOOR OR AMPLY VENTILATED AREA USE |
| BS EN 89:2015 | Gas-fired storage water heaters for the production of domestic hot water |
| BS EN 12252:2014 | LPG equipment and accessories. Equipping of LPG road tankers |
| UNE-EN 14678-1:2013 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers |
| UNE-EN 13953:2015 | LPG equipment and accessories - Pressure relief valves for transportable refillable cylinders for Liquefied Petroleum Gas (LPG) |
| UNI EN 15202 : 2012 | LPG EQUIPMENT AND ACCESSORIES - ESSENTIAL OPERATIONAL DIMENSIONS FOR LPG CYLINDER VALVE OUTLET AND ASSOCIATED EQUIPMENT CONNECTIONS |
| UNE-EN 16125:2016 | LPG Equipment and Accessories - Pipework systems and supports - LPG in liquid phase and vapour pressure phase |
| EN 14678-1:2013 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers |
| EN 449:2002+A1:2007 | Specification for dedicated liquefied petroleum gas appliances - Domestic flueless space heaters (including diffusive catalytic combustion heaters) |
| UNI EN 13799 : 2012 | LPG EQUIPMENT AND ACCESSORIES - CONTENTS GAUGES FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSELS |
| EN 50465:2015 | Gas appliances - Combined heat and power appliance of nominal heat input inferior or equal to 70 kW |
| UNI EN 14893 : 2014 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| UNI EN 624 : 2011 | SPECIFICATION FOR DEDICATED LPG APPLIANCES - ROOM SEALED LPG SPACE HEATING EQUIPMENT FOR INSTALLATION IN VEHICLES AND BOATS |
| UNI EN 1106 : 2010 | MANUALLY OPERATED TAPS FOR GAS BURNING APPLIANCES |
| UNI EN 13774 : 2013 | VALVES FOR GAS DISTRIBUTION SYSTEMS WITH MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 16 BAR - PERFORMANCE REQUIREMENTS |
| UNI EN 14141 : 2013 | VALVES FOR NATURAL GAS TRANSPORTATION IN PIPELINES - PERFORMANCE REQUIREMENTS AND TESTS |
| UNI EN 15069 : 2009 | SAFETY GAS CONNECTION VALVES FOR METAL HOSE ASSEMBLIES USED FOR THE CONNECTION OF DOMESTIC APPLIANCES USING GASEOUS FUEL |
| UNI EN 14800 : 2007 | CORRUGATED SAFETY METAL HOSE ASSEMBLIES FOR THE CONNECTION DOMESTIC APPLIANCES USING GASEOUS FUELS |
| UNI EN 1854 : 2010 | PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES |
| UNI EN 14129 : 2014 | LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR LPG PRESSURE VESSELS |
| UNI EN 12864 : 2010 | LOW-PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| UNI EN 14678-2 : 2012 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS AND INSTALLATION REQUIREMENTS |
| UNI EN 14678-1 : 2013 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS |
| UNI EN 12252 : 2014 | LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS |
| UNI EN 13786 : 2009 | AUTOMATIC CHANGE-OVER VALVES HAVING A MAXIMUM OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| UNI EN 13785 : 2009 | REGULATORS WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, HAVING A MAXIMUM NOMINAL OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR, OTHER THAN THOSE COVERED BY EN 12864 AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| UNI EN 16129 : 2013 | PRESSURE REGULATORS, AUTOMATIC CHANGE-OVER DEVICES, HAVING A MAXIMUM REGULATED PRESSURE OF 4 BAR, WITH A MAXIMUM CAPACITY OF 150 KG/H, ASSOCIATED SAFETY DEVICES AND ADAPTORS FOR BUTANE, PROPANE, AND THEIR MIXTURES |
| BS ISO 15995:2006 | Gas cylinders. Specification and testing of LPG cylinder valves. Manually operated |
| 10/30218991 DC : 0 | BS EN 16119 - LPG EQUIPMENT AND ACCESSORIES - SEALING CAPS AND PLUGS FOR CYLINDER AND TANK VALVES - SPECIFICATION AND TESTING |
| PREN 484 : DRAFT 2015 | SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - INDEPENDENT STOVES, INCLUDING THOSE INCORPORATING A GRILL FOR OUTDOOR USE |
| 17/30360051 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| BS EN 16678:2015 | Safety and control devices for gas burners and gas burning appliances. Automatic shut-off valves for operating pressure of above 500 kPa up to and including 6 300 kPa |
| I.S. EN 13153:2002 | SPECIFICATION AND TESTING OF LPG CYLINDER VALVES - MANUALLY OPERATED |
| UNE-EN 1254-8:2013 | Copper and copper alloys - Plumbing fittings - Part 8: Fittings with press ends for use with plastics and multilayer pipes |
| 04/30111048 DC : 0 | EN 88-2 - PRESSURE GOVERNORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 2 - PRESSURE GOVERNORS FOR INLET PRESSURES BETWEEN 0.5 BAR AND 5 BAR |
| PREN 14678-1 : DRAFT 2010 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS |
| 14/30300117 DC : 0 | BS EN 13175 - LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSEL VALVES AND FITTINGS |
| 11/30248438 DC : 0 | BS EN 14141 - VALVES FOR NATURAL GAS TRANSPORTATION IN PIPELINES - PERFORMANCE REQUIREMENTS AND TESTS |
| 05/30125303 DC : DRAFT APR 2005 | BS EN 15202 - LPG EQUIPMENT AND ACCESSORIES - ESSENTIAL OPERATIONAL DIMENSIONS FOR LPG CYLINDER VALVE OUTLET AND ASSOCIATED EQUIPMENT CONNECTIONS |
| 12/30266928 DC : 0 | BS EN 14071 - LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR LPG PRESSURE VESSELS - ANCILLARY EQUIPMENT |
| PREN 16617 : DRAFT 2013 | PIPEWORK - CORRUGATED METAL HOSE ASSEMBLIES FOR COMBUSTIBLE GAS - PERFORMANCE REQUIREMENTS, TESTING AND MARKING |
| 12/30254956 DC : 0 | BS EN 26 - GAS-FIRED INSTANTANEOUS WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| 13/30281067 DC : 0 | BS EN 12252 - LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS |
| 12/30258236 DC : 0 | BS EN 10358 - UNALLOYED STEEL PLUMBING FITTINGS - FITTINGS WITH PRESS ENDS FOR UNALLOYED STEEL TUBES |
| EN 1254-8:2012 | Copper and copper alloys - Plumbing fittings - Part 8: Fittings with press ends for use with plastics and multilayer pipes |
| UNE-EN 13175:2015 | LPG Equipment and accessories - Specification and testing for Liquefied Petroleum Gas (LPG) pressure vessel valves and fittings |
| 08/30180918 DC : DRAFT JULY 2008 | BS EN 1854 - PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES |
| BS ISO 14245:2006 | Gas cylinders. Specification and testing of LPG cylinder valves. Self-closing |
| DIN EN 16125:2016-03 | LPG EQUIPMENT AND ACCESSORIES - PIPEWORK SYSTEMS AND SUPPORTS - LPG LIQUID PHASE AND VAPOUR PRESSURE PHASE |
| UNE-EN 16617:2015 | Pipework - Corrugated metal hose assemblies for combustible gas - Performance requirements, testing and marking |
| UNI EN ISO 15995 : 2010 | GAS CYLINDERS - SPECIFICATIONS AND TESTING OF LPG CYLINDER VALVES - MANUALLY OPERATED |
| PREN 331 : DRAFT 2013 | MANUALLY OPERATED BALL VALVES AND CLOSED BOTTOM TAPER PLUG VALVES FOR GAS INSTALLATIONS FOR BUILDINGS |
| BS EN 16125:2015 | LPG Equipment and Accessories. Pipework systems and supports. LPG in liquid phase and vapour pressure phase |
| ISO 17484-1:2014 | Plastics piping systems — Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) — Part 1: Specifications for systems |
| UNE-EN 13611:2016 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements |
| DIN EN 13611:2016-09 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| 15/30296472 DC : 0 | BS EN 54-7 - FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 7: SMOKE DETECTORS - POINT DETECTORS USING SCATTERED LIGHT, TRANSMITTED LIGHT OR IONIZATION |
| 16/30334721 DC : 0 | BS EN 521 - SPECIFICATIONS FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PORTABLE VAPOUR PRESSURE LIQUEFIED PETROLEUM GAS APPLIANCES |
| PREN 13799 : DRAFT 2009 | LPG EQUIPMENT AND ACCESSORIES - CONTENTS GAUGES FOR LPG TANKS |
| PREN 14893 : DRAFT 2013 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE LIQUEFIED PETROLEUM GAS (LPG) WELDED STEEL PRESSURE DRUMS WITH A CAPACITY BETWEEN 150 LITRES AND 1000 LITRES |
| I.S. EN ISO 15995:2010 | GAS CYLINDERS - SPECIFICATIONS AND TESTING OF LPG CYLINDER VALVES - MANUALLY OPERATED |
| DIN EN 13953:2015-05 | LPG equipment and accessories - Pressure relief valves for transportable refillable cylinders for Liquefied Petroleum Gas (LPG) |
| DIN EN 14129:2014-05 | LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR LPG PRESSURE VESSELS |
| DIN EN 88-2:2008-03 | Pressure regulators and associated safety devices for gas appliances - Part 2: Pressure regulators for inlet pressures above 500 mbar up to and including 5 bar |
| DIN EN 13774:2013-05 | VALVES FOR GAS DISTRIBUTION SYSTEMS WITH MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 16 BAR - PERFORMANCE REQUIREMENTS |
| DIN EN 13799:2012-06 | LPG equipment and accessories - Contents gauges for Liquefied Petroleum Gas (LPG) pressure vessels |
| 04/30124829 DC : 0 | EN 15070 - STRIP WOUND FLEXIBLE SAFETY METALLIC HOSE ASSEMBLIES FOR THE CONNECTION OF DOMESTIC APPLIANCES USING GASEOUS FUELS |
| BS EN 13774:2013 | Valves for gas distribution systems with maximum operating pressure less than or equal to 16 bar. Performance requirements |
| BS EN 14129:2014 | LPG Equipment and accessories. Pressure relief valves for LPG pressure vessels |
| BS EN 10284:2000 | Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems |
| BS EN 15033:2006 | Room sealed storage water heaters for the production of sanitary hot water using LPG for vehicles and boats |
| UNE-EN 13774:2013 | Valves for gas distribution systems with maximum operating pressure less than or equal to 16 bar - Performance requirements |
| BS EN 13799:2012 | LPG equipment and accessories. Contents gauges for Liquefied Petroleum Gas (LPG) pressure vessels |
| BS EN 331:2015 | Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings |
| UNE-EN 1439:2017 | LPG equipment and accessories - Procedure for checking transportable refillable LPG cylinders before, during and after filling |
| BS EN 12864 : 2001 | LOW-PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| DIN EN 15069:2010-07 | Safety gas connection valves for metal hose assemblies used for the connection of domestic appliances using gaseous fuel |
| UNE-EN 30-1-1:2009 | Domestic cooking appliances burning gas - Part 1-1: Safety - General |
| BS EN 483 : 2000 | GAS-FIRED CENTRAL HEATING BOILERS - TYPE C BOILERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW |
| BS EN 13152:2002 | Specification and testing of LPG cylinder valves. Self closing |
| UNE-EN 15202:2012 | LPG equipment and accessories - Essential operational dimensions for LPG cylinder valve outlet and associated equipment connections |
| UNE-EN 14543:2006 | Specification for dedicated liquefied petroleum gas appliances - Parasol patio heaters - Flueless radiant heaters for outdoor or amply ventilated area use |
| BS EN 13953:2015 | LPG equipment and accessories. Pressure relief valves for transportable refillable cylinders for Liquefied Petroleum Gas (LPG) |
| UNE-EN 89:2016 | Gas-fired storage water heaters for the production of domestic hot water |
| UNE-EN 26:2016 | Gas-fired instantaneous water heaters for the production of domestic hot water |
| BS EN 13787:2001 | Elastomers for gas pressure regulators and associated safety devices for inlet pressures up to 100 bar |
| UNE-EN 624:2011 | Specification for dedicated LPG appliances - Room sealed LPG space heating equipment for installation in vehicles and boats |
| BS EN 14800:2007 | Corrugated safety metal hose assemblies for the connection of domestic appliances using gaseous fuels |
| EN 89:2015 | Gas-fired storage water heaters for the production of domestic hot water |
| EN 15069:2008 | Safety gas connection valves for metal hose assemblies used for the connection of domestic appliances using gaseous fuel |
| EN 13799:2012 | LPG equipment and accessories - Contents gauges for Liquefied Petroleum Gas (LPG) pressure vessels |
| EN 15266:2007 | Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar |
| EN 14893:2014 | LPG equipment and accessories - Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres |
| EN 14543:2017 | Specification for dedicated liquefied petroleum gas appliances - Parasol patio heaters - Flueless radiant heaters for outdoor or amply ventilated area use |
| EN 13774:2013 | Valves for gas distribution systems with maximum operating pressure less than or equal to 16 bar - Performance requirements |
| EN 13786:2004+A1:2008 | Automatic change-over valves having a maximum outlet pressure of up to and including 4 bar with a capacity of up to and including 100 kg/h, and their associated safety devices for butane, propane or their mixtures |
| EN 16678:2015 | Safety and control devices for gas burners and gas burning appliances - Automatic shut-off valves for operating pressure of above 500 kPa up to and including 6 300 kPa |
| EN 13785:2005+A1:2008 | Regulators with a capacity of up to and including 100 kg/h, having a maximum nominal outlet pressure of up to and including 4 bar, other than those covered by EN 12864 and their associated safety devices for butane, propane or their mixtures |
| EN 14678-2:2007+A1:2012 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 2: Components other than dispensers and installation requirements |
| EN 16125:2015 | LPG Equipment and Accessories - Pipework systems and supports - LPG in liquid phase and vapour pressure phase |
| EN 1359:2017 | Gas meters - Diaphragm gas meters |
| EN 26:2015 | Gas-fired instantaneous water heaters for the production of domestic hot water |
| EN 14129:2014 | LPG Equipment and accessories - Pressure relief valves for LPG pressure vessels |
| EN 14141:2013 | Valves for natural gas transportation in pipelines - Performance requirements and tests |
| EN 13787:2001 | Elastomers for gas pressure regulators and associated safety devices for inlet pressures up to 100 bar |
| EN 14678-3:2013 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 3: Refuelling installations at commercial and industrial premises |
| EN 14800:2007 | Corrugated safety metal hose assemblies for the connection of domestic appliances using gaseous fuels |
| EN 624:2011 | Specification for dedicated LPG appliances - Room sealed LPG space heating equipment for installation in vehicles and boats |
| EN 88-2:2007 | Pressure regulators and associated safety devices for gas appliances - Part 2: Pressure regulators for inlet pressures above 500 mbar up to and including 5 bar |
| EN 14829:2007 | Independent gas-fired flueless space heaters for nominal heat input not exceeding 6 kW |
| EN 16617:2015 | Pipework - Corrugated metal hose assemblies for combustible gas - Performance requirements, testing and marking |
| EN 331:2015 | Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings |
| PREN 12252 : DRAFT 2013 | LPG EQUIPMENT AND ACCESSORIES - EQUIPPING OF LPG ROAD TANKERS |
| UNE-EN 14893:2014 | LPG equipment and accessories - Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres |
| UNI EN ISO 14245 : 2010 | GAS CYLINDERS - SPECIFICATIONS AND TESTING OF LPG CYLINDER VALVES - SELF-CLOSING |
| 10/30218994 DC : 0 | BS EN 15202 - LPG EQUIPMENT AND ACCESSORIES - ESSENTIAL OPERATIONAL DIMENSIONS FOR LPG CYLINDER VALVE OUTLET AND ASSOCIATED EQUIPMENT CONNECTIONS |
| PREN 88-2 : DRAFT 2014 | SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 2: PRESSURE REGULATORS FOR INLET PRESSURES ABOVE 50 KPA UP TO AND INCLUDING 500 KPA AND ASSOCIATED SAFETY DEVICES |
| 12/30257022 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - GENERAL REQUIREMENTS |
| BS EN 16119:2013 | LPG equipment and accessories. Sealing caps and plugs for LPG cylinder and pressure vessel valves. Specification and testing |
| BS EN 16129:2013 | Pressure regulators, automatic change-over devices, having a maximum regulated pressure of 4 bar, with a maximum capacity of 150 kg/h, associated safety devices and adaptors for butane, propane, and their mixtures |
| 11/30243885 DC : 0 | BS EN 13774 - VALVES FOR GAS DISTRIBUTION SYSTEMS WITH MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 16 BAR - PERFORMANCE REQUIREMENTS |
| 11/30249911 DC : 0 | BS EN 50465 - GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| 18/30321883 DC : 0 | BS EN ISO 15995 - GAS CYLINDERS - SPECIFICATIONS AND TESTING OF LPG CYLINDER VALVES - MANUALLY OPERATED |
| 09/30201902 DC : 0 | BS EN 624 - SPECIFICATION FOR DEDICATED LPG APPLIANCES - ROOM SEALED LPG SPACE HEATING EQUIPMENT FOR INSTALLATION IN VEHICLES AND BOATS |
| DIN EN 16129:2013-08 | Pressure regulators, automatic change-over devices, having a maximum regulated pressure of 4 bar, with a maximum capacity of 150kg/h, associated safety devices and adaptors for butane, propane, and their mixtures |
| I.S. EN 16119:2013 | LPG EQUIPMENT AND ACCESSORIES - SEALING CAPS AND PLUGS FOR LPG CYLINDER AND PRESSURE VESSEL VALVES - SPECIFICATION AND TESTING |
| BS ISO 17484-1:2014 | Plastics piping systems. Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) Specifications for systems |
| 06/19977015 DC : DRAFT JULY 2006 | BS EN 10344 - MALLEABLE CAST IRON FITTINGS WITH COMPRESSION ENDS FOR STEEL PIPES |
| 11/30237753 DC : 0 | BS ISO 17484-1 - PLASTICS PIPING SYSTEMS - MULTILAYER PIPE SYSTEMS FOR INDOOR GAS INSTALLATIONS WITH A MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 5 BAR (500 KPA) - PART 1: SPECIFICATIONS FOR SYSTEMS |
| UNE-EN 14678-3:2013 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 3: Refuelling installations at commercial and industrial premises |
| 04/30095590 DC : 0 | EN 1254-7 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 7: FITTINGS WITH PRESS ENDS FOR METALLIC TUBES |
| DIN EN 16678:2016-02 | Safety and control devices for gas burners and gas burning appliances - Automatic shut-off valves for operating pressure of above 500 kPa up to and including 6 300 kPa |
| DIN EN 1439:2015-10 (Draft) | LPG EQUIPMENT AND ACCESSORIES - PROCEDURE FOR CHECKING TRANSPORTABLE REFILLABLE LPG CYLINDERS BEFORE, DURING AND AFTER FILLING |
| UNE-EN 15266:2008 | Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar |
| I.S. EN 1254-8:2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 8: FITTINGS WITH PRESS ENDS FOR USE WITH PLASTICS AND MULTILAYER PIPES |
| I.S. EN 16129:2013 | PRESSURE REGULATORS, AUTOMATIC CHANGEOVER DEVICES, HAVING A MAXIMUM REGULATED PRESSURE OF 4 BAR, WITH A MAXIMUM CAPACITY OF 150 KG/H, ASSOCIATED SAFETY DEVICES AND ADAPTORS FOR BUTANE, PROPANE, AND THEIR MIXTURES |
| I.S. EN 521:2006 | SPECIFICATIONS FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - PORTABLE VAPOUR PRESSURE LIQUEFIED PETROLEUM GAS APPLIANCES |
| BS EN 13611:2015 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels. General requirements |
| I.S. EN 16678:2015 | SAFETY AND CONTROL DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES - AUTOMATIC SHUT-OFF VALVES FOR OPERATING PRESSURE OF ABOVE 500 KPA UP TO AND INCLUDING 6300 KPA |
| DIN EN 13175:2015-02 | LPG EQUIPMENT AND ACCESSORIES - SPECIFICATION AND TESTING FOR LIQUEFIED PETROLEUM GAS (LPG) PRESSURE VESSEL VALVES AND FITTINGS |
| DIN EN 14071:2015-08 | LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR LPG PRESSURE VESSELS - ANCILLARY EQUIPMENT |
| PREN 13611 : DRAFT 2017 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| DIN EN 624:2011-10 | Specification for dedicated LPG appliances - Room sealed LPG space heating equipment for installation in vehicles and boats |
| DIN EN 14678-1:2013-06 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers |
| DIN EN 30-1-1:2013-06 | Domestic cooking appliances burning gas - Part 1-1: Safety - General (includes Amendment 1:2013) |
| BS EN 14543:2017 | Specification for dedicated liquefied petroleum gas appliances. Parasol patio heaters. Flueless radiant heaters for outdoor or amply ventilated area use |
| BS EN 13090:2000 | Means for resealing threaded joints of gas pipework in buildings |
| BS EN 14678-1:2013 | LPG equipment and accessories. Construction and performance of LPG equipment for automotive filling stations Dispensers |
| BS EN 1439:2017 | LPG equipment and accessories. Procedure for checking transportable refillable LPG cylinders before, during and after filling |
| BS EN 1359:2017 | Gas meters. Diaphragm gas meters |
| BS EN 14893:2014 | LPG equipment and accessories. Transportable Liquefied Petroleum Gas (LPG) welded steel pressure drums with a capacity between 150 litres and 1 000 litres |
| BS EN 461:1999 | Specification for dedicated liquefied petroluem gas appliances. Flueless non-domestic space heaters not exceeding 10 kW |
| BS EN 30-1-1 : 2008 | DOMESTIC COOKING APPLIANCES BURNING GAS - PART 1-1: SAFETY - GENERAL |
| BS EN 13153:2002 | Specification and testing of LPG cylinder valves. Manually operated |
| EN 10284:2000 | Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems |
| EN 13090:2000 | Means for resealing threaded joints of gas pipework in buildings |
| DIN EN 15202:2012-09 | LPG EQUIPMENT AND ACCESSORIES - ESSENTIAL OPERATIONAL DIMENSIONS FOR LPG CYLINDER VALVE OUTLET AND ASSOCIATED EQUIPMENT CONNECTIONS |
| EN 12252:2014 | LPG equipment and accessories - Equipping of LPG road tankers |
| EN 13760:2003 | Automotive LPG filling system for light and heavy duty vehicles - Nozzle, test requirements and dimensions |
| I.S. EN 13611:2015/AC:2016 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| EN 16119:2013 | LPG equipment and accessories - Sealing caps and plugs for LPG cylinder and pressure vessel valves - Specification and testing |
| DIN EN 449:2008-03 | SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM GAS APPLIANCES - DOMESTIC FLUELESS SPACE HEATERS (INCLUDING DIFFUSIVE CATALYTIC COMBUSTION HEATERS) |
| UNI EN 30-1-1 : 2013 | DOMESTIC COOKING APPLIANCES BURNING GAS - PART 1-1: SAFETY - GENERAL |
| EN 13152:2001/A1:2003 | SPECIFICATION AND TESTING OF LPG CYLINDER VALVES - SELF CLOSING |
| UNE-EN 16125:2020 | LPG Equipment and Accessories - Pipework systems and supports - LPG in liquid phase and vapour pressure phase |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing |
| ISO 1400:1975 | Vulcanized rubbers of high hardness (85 to 100 IRHD) Determination of hardness |
| ISO 1407:2011 | Rubber — Determination of solvent extract |
| ISO 4648:1991 | Rubber, vulcanized or thermoplastic Determination of dimensions of test pieces and products for test purposes |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 471:1995 | Rubber Temperatures, humidities and times for conditioning and testing |
| ISO 247:2006 | Rubber Determination of ash |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| ISO 4650:2012 | Rubber — Identification — Infrared spectrometric methods |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.