Customer Support: 131 242

  • Shopping Cart
    There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 50583-1:2016

Current

Current

The latest, up-to-date edition.

Photovoltaics in buildings - Part 1: BIPV modules

Published date

15-01-2016

Sorry this product is not available in your region.

European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Labelling
6 Documentation and declaration of performance
Annex A (normative) - Further requirements on PV
        modules that contain glass
Bibliography

This document applies to photovoltaic modules used as construction products. It focuses on the properties of these photovoltaic modules relevant to essential building requirements as specified in the European Construction Product Regulation CPR 305/2011, and the applicable electro-technical requirements as stated in the Low Voltage Directive 2006/95/EC / or CENELEC standards. This document references international standards, technical reports and guidelines. For some applications in addition national standards (or regulations) for building products may apply in individual countries, which are not explicitly referenced here and for which harmonized European Standards are not yet available.The document is addressed to manufacturers, planners, system designers, installers, testing institutes and building authorities.This document does not apply to concentrating or building-attached photovoltaic modules. This document addresses requirements on the PV modules in the specific ways they are intended to be mounted but not the mounting structure itself, which is within the scope of FprEN 50583- 2.

Committee
CLC/TC 82
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Current

I.S. EN 50583-2:2016 PHOTOVOLTAICS IN BUILDINGS - PART 2: BIPV SYSTEMS
EN 50583-2:2016 Photovoltaics in buildings - Part 2: BIPV systems
BS EN 50583-2:2016 Photovoltaics in buildings BIPV systems
UNE-EN 50583-2:2016 Photovoltaics in buildings - Part 2: BIPV systems

EN 14783:2013 Fully supported metal sheet and strip for roofing, external cladding and internal lining - Product specification and requirements
EN 13116:2001 Curtain walling - Resistance to wind load - Performance requirements
CLC/TS 61836:2009 Solar photovoltaic energy systems - Terms, definitions and symbols
EN 673:2011 Glass in building - Determination of thermal transmittance (U value) - Calculation method
ISO 12631:2017 Thermal performance of curtain walling — Calculation of thermal transmittance
EN 1096-4:2004 Glass in building - Coated glass - Part 4: Evaluation of conformity/Product standard
EN 12758:2011 Glass in building - Glazing and airborne sound insulation - Product descriptions and determination of properties
EN 410:2011 Glass in building - Determination of luminous and solar characteristics of glazing
IEC 61215:2005 Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval
PREN 1279-5 : DRAFT 2015 GLASS IN BUILDING - INSULATING GLASS UNITS - PART 5: EVALUATION OF CONFORMITY
EN 14782:2006 Self-supporting metal sheet for roofing, external cladding and internal lining - Product specification and requirements
IEC 61730-2:2016 Photovoltaic (PV) module safety qualification - Part 2: Requirements for testing
IEC TS 61836:2007 Solar photovoltaic energy systems - Terms, definitions and symbols
EN ISO 12543-2:2011 Glass in building - Laminated glass and laminated safety glass - Part 2: Laminated safety glass (ISO 12543-2:2011)
EN 61646:2008 THIN-FILM TERRESTRIAL PHOTOVOLTAIC (PV) MODULES - DESIGN QUALIFICATION AND TYPE APPROVAL
EN 15978:2011 Sustainability of construction works - Assessment of environmental performance of buildings - Calculation method
EN 15804:2012 Sustainability of construction works - Environmental product declarations - Core rules for the product category of construction products
EN 61730-1:2007/A11:2014 PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION (IEC 61730-1:2004, MODIFIED)
ISO 12543-3:2011 Glass in building Laminated glass and laminated safety glass Part 3: Laminated glass
EN 14500:2008 Blinds and shutters - Thermal and visual comfort - Test and calculation methods
EN 13501-5:2016 Fire classification of construction products and building elements - Part 5: Classification using data from external fire exposure to roofs tests
EN 62446:2009 Grid connected photovoltaic systems – Minimum requirements for system documentation, commissioning tests and inspection
EN ISO 12543-3:2011 Glass in building - Laminated glass and laminated safety glass - Part 3: Laminated glass (ISO 12543-3:2011)
EN 82079-1:2012 Preparation of instructions for use - Structuring, content and presentation - Part 1: General principles and detailed requirements
EN ISO 12631:2017 Thermal performance of curtain walling - Calculation of thermal transmittance (ISO 12631:2017)
EN 13501-2:2016 Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance tests, excluding ventilation services
EN 14179-2:2005 Glass in building - Heat soaked thermally toughened soda lime silicate safety glass - Part 2: Evaluation of conformity/Product standard
IEC 61082-1:2014 RLV Preparation of documents used in electrotechnology - Part 1: Rules
CEN/TR 15941:2010 Sustainability of construction works - Environmental product declarations - Methodology for selection and use of generic data
ISO 12543-2:2011 Glass in building Laminated glass and laminated safety glass Part 2: Laminated safety glass
EN 12519:2004 Windows and pedestrian doors - Terminology
EN 1279-3:2002 Glass in building - Insulating glass units - Part 3: Long term test method and requirements for gas leakage rate and for gas concentration tolerances
IEC 61646:2008 Thin-film terrestrial photovoltaic (PV) modules - Design qualification and type approval
EN 572-9:2004 Glass in building - Basic soda lime silicate glass products - Part 9: Evaluation of conformity/Product standard
EN 1279-4:2002 Glass in building - Insulating glass units - Part 4: Methods of test for the physical attributes of edge seals
EN 1863-2:2004 Glass in building - Heat strengthened soda lime silicate glass - Part 2: Evaluation of conformity/Product standard
EN 61730-2:2007/A1:2012 PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 2: REQUIREMENTS FOR TESTING (IEC 61730-2:2004/A1:2011)
EN 674:2011 Glass in building - Determination of thermal transmittance (U value) - Guarded hot plate method
EN 15942:2011 Sustainability of construction works - Environmental product declarations - Communication format business-to-business
EN 12150-2:2004 Glass in building - Thermally toughened soda lime silicate safety glass - Part 2: Evaluation of conformity/Product standard
IEC 61730-1:2016 Photovoltaic (PV) module safety qualification - Part 1: Requirements for construction
EN 13830:2015 Curtain walling - Product standard
ISO 12543-1:2011 Glass in building Laminated glass and laminated safety glass Part 1: Definitions and description of component parts
EN 12179:2000 Curtain walling - Resistance to wind load - Test method
EN 61082-1:2015 Preparation of documents used in electrotechnology - Part 1: Rules
EN 675:2011 Glass in building - Determination of thermal transmittance (U value) - Heat flow meter method
EN 1279-2:2002 Glass in building - Insulating glass units - Part 2: Long term test method and requirements for moisture penetration
IEC 62446:2009 Grid connected photovoltaic systems - Minimum requirements for system documentation, commissioning tests and inspection
EN 13119:2016 Curtain walling - Terminology
ISO 12543-4:2011 Glass in building Laminated glass and laminated safety glass Part 4: Test methods for durability
EN ISO 12543-4:2011 Glass in building - Laminated glass and laminated safety glass - Part 4: Test methods for durability (ISO 12543-4:2011)
ISO 12543-6:2011 Glass in building Laminated glass and laminated safety glass Part 6: Appearance
EN 14351-1:2006+A2:2016 Windows and doors - Product standard, performance characteristics - Part 1: Windows and external pedestrian doorsets
EN ISO 12543-5:2011 Glass in building - Laminated glass and laminated safety glass - Part 5: Dimensions and edge finishing (ISO 12543-5:2011)
EN 13956:2012 Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing - Definitions and characteristics
IEC 82079-1:2012 Preparation of instructions for use - Structuring, content and presentation - Part 1: General principles and detailed requirements
EN 16002:2010 Flexible sheets for waterproofing - Determination of the resistance to wind load of mechanically fastened flexible sheets for roof waterproofing
EN 50380:2017 Marking and documentation requirements for Photovoltaic Modules
ISO 12543-5:2011 Glass in building Laminated glass and laminated safety glass Part 5: Dimensions and edge finishing
EN 61215:2005 Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval
EN ISO 12543-1:2011 Glass in building - Laminated glass and laminated safety glass - Part 1: Definitions and description of component parts (ISO 12543-1:2011)
EN 12600:2002 Glass in building - Pendulum test - Impact test method and classification for flat glass

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.