Customer Support: 131 242

  • Shopping Cart
    There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 15497:2014

Current

Current

The latest, up-to-date edition.

Structural finger jointed solid timber - Performance requirements and minimum production requirements

Published date

30-04-2014

Sorry this product is not available in your region.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Performance characteristics for structural finger
 jointed timber
6 Assessment and Verification of Constancy of
  Performance (AVCP)
7 Marking and labelling
Annex A (normative) - Release of Formaldehyde
Annex B (normative) - Additional test methods and provisions
        for adhesives
Annex C (normative) - Bending tests with finger joints (including
        compliance criteria)
Annex D (normative) - Measurement of moisture content
Annex E (normative) - Equipment
Annex F (normative) - Separation tests with finger joints produced
        with contact-free application of adhesive
Annex G (normative) - Minimum production provisions
Annex ZA (informative) - Clauses of this European Standard
         addressing the provisions of EU Construction Products
         Regulation
Bibliography

This European Standard sets out provisions regarding the performance characteristics for structural finger jointed timber with rectangular cross section for use in buildings and bridges.The use of structural finger jointed timber may be limited to certain service classes in some member states.It also lays down minimum production provisions and procedures for Assessment and Verification of Constancy of Performance for structural finger jointed timber.This European Standard is applicable to structural finger jointed timber made of coniferous timber species listed in this standard or poplar.Although it may be possible to produce structural finger jointed timber made from specific broadleaf species based on some provisions of this European Standard, this standard is not applicable to these products.This European Standard is only applicable to finger joints between timber sections of the same species.This European Standard does not cover impressed (die-formed) finger joints.This European Standard covers structural finger jointed timber untreated or treated against biological attack. Structural finger jointed timber treated with fire retardants is not covered.

Committee
CEN/TC 124
DevelopmentNote
Supersedes PREN 15497. Together with EN 14080, it supersedes EN 385. (05/2014)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current
Supersedes

Standards Relationship
NF EN 15497 : 2014 Identical
UNE-EN 15497:2014 Identical
DIN EN 15497:2014-07 Identical
UNI EN 15497 : 2014 Identical
PN-EN 15497:2014-06 Identical
NBN EN 15497 : 2014 Identical
I.S. EN 15497:2014 Identical
NS EN 15497 : 2014 Identical
SN EN 15497 : 2014 Identical
NEN EN 15497 : 2014 Identical
BS EN 15497:2014 Identical
DIN EN 15497 E : 2014 Identical

BS EN 16351:2015 Timber structures. Cross laminated timber. Requirements
EN 16351:2015 Timber structures - Cross laminated timber - Requirements
DIN EN 16351:2015-12 Timber structures - Cross laminated timber - Requirements
I.S. EN 16351:2015 TIMBER STRUCTURES - CROSS LAMINATED TIMBER - REQUIREMENTS
UNE-EN 16351:2016 Timber structures - Cross laminated timber - Requirements

EN 13183-3:2005 Moisture content of a piece of sawn timber - Part 3: Estimation by capacitance method
EN 302-5:2013 Adhesives for load-bearing timber structures - Test methods - Part 5: Determination of maximum assembly time under referenced conditions
EN 14081-2:2010+A1:2012 Timber structures - Strength graded structural timber with rectangular cross section - Part 2: Machine grading; additional requirements for initial type testing
EN 15416-5:2017 Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5: Determination of minimum pressing time under referenced conditions
EN 302-2:2017 Adhesives for load-bearing timber structures - Test methods - Part 2: Determination of resistance to delamination
EN 15416-3:2017 Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 3: Creep deformation test at cyclic climate conditions with specimens loaded in bending shear
EN 717-1:2004 Wood-based panels - Determination of formaldehyde release - Part 1: Formaldehyde emission by the chamber method
EN 14081-4:2009 Timber structures - Strength graded structural timber with rectangular cross section - Part 4: Machine grading - Grading machine settings for machine controlled systems
EN 13501-2:2016 Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance tests, excluding ventilation services
EN 301:2017 Adhesives, phenolic and aminoplastic, for load-bearing timber structures - Classification and performance requirements
EN 13556:2003 Round and sawn timber - Nomenclature of timbers used in Europe
EN 302-1:2013 Adhesives for load-bearing timber structures - Test methods - Part 1: Determination of longitudinal tensile shear strength
EN 16351:2015 Timber structures - Cross laminated timber - Requirements
EN 13238:2010 Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates
EN 13823:2010+A1:2014 Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item
EN 350-2:1994 Durability of wood and wood-based products - Natural durability of solid wood - Part 2: Guide to natural durability and treatability of selected wood species of importance in Europe
EN 14081-1:2016 Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements
EN 336:2013 Structural timber - Sizes, permitted deviations
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 302-4:2013 Adhesives for load-bearing timber structures - Test methods - Part 4: Determination of the effects of wood shrinkage on the shear strength
EN 302-3:2017 Adhesives for load-bearing timber structures - Test methods - Part 3: Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength
EN 408:2010+A1:2012 Timber structures - Structural timber and glued laminated timber - Determination of some physical and mechanical properties
EN 15425:2017 Adhesives - One component polyurethane (PUR) for load-bearing timber structures - Classification and performance requirements
ISO 9001:2015 Quality management systems — Requirements
EN 338:2016 Structural timber - Strength classes
EN 14358:2016 Timber structures - Calculation and verification of characteristic values
EN 14080:2013 Timber structures - Glued laminated timber and glued solid timber - Requirements
EN 14081-3:2012 Timber structures - Strength graded structural timber with rectangular cross section - Part 3: Machine grading; additional requirements for factory production control
EN 15228:2009 Structural timber - Structural timber preservative treated against biological attack

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.