EN 1402-6:2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Unshaped refractory products - Part 6: Measurement of physical properties
01-12-2012
15-10-2003
Foreword
1 Scope
2 Normative references
3 Determination of geometric bulk density
4 Determination of density and porosity
5 Determination of cold modulus of rupture
6 Determination of cold crushing strength
7 Determination of permanent linear change
8 Determination of modulus of rupture at elevated
temperatures
9 Determination of refractoriness under load and
creep in compression
10 Test report
Bibliography
This standard specifies methods for the determination of properties of unshaped materials from test pieces prepared and stored according to prENV 1402-5. The methods are applicable to dense and insulating castables and to mouldable materials (plastics and ramming mixes) as defined in ENV 1402-1 before and after firing.
| Committee |
CEN/TC 187
|
| DevelopmentNote |
Supersedes ENV 1402-6. (11/2003)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| SN EN 1402-6 : 2003 | Identical |
| I.S. EN 1402-6:2003 | Identical |
| NF EN 1402-6 : 2004 | Identical |
| PN EN 1402-6 : 2005 | Identical |
| UNI EN 1402-6 : 2004 | Identical |
| BS EN 1402-6:2003 | Identical |
| NEN EN 1402-6 : 2003 | Identical |
| NS EN 1402-6 : 1ED 2003 | Identical |
| UNE-EN 1402-6:2004 | Identical |
| NBN EN 1402-6 : 2003 | Identical |
| DIN EN 1402-6:2004-01 | Identical |
| I.S. EN 1402-1:2003 | UNSHAPED REFRACTORY PRODUCTS - PART 1: INTRODUCTION AND CLASSIFICATION |
| BS EN 1402-8:2003 | Unshaped refractory products Determination of complementary properties |
| I.S. EN 1402-7:2003 | UNSHAPED REFRACTORY MATERIALS - PART 7: TESTS ON PRE-FORMED SHAPES |
| DIN EN 1402-1:2004-01 | UNSHAPED REFRACTORY PRODUCTS - PART 1: INTRODUCTION AND CLASSIFICATION |
| DIN EN 993-20:2004-08 | METHODS OF TEST FOR DENSE SHAPED REFRACTORY PRODUCTS - PART 20: DETERMINATION OF RESISTANCE TO ABRASION AT AMBIENT TEMPERATURE |
| DIN EN 1402-7:2004-01 | UNSHAPED REFRACTORY MATERIALS - PART 7: TESTS ON PRE-FORMED SHAPES |
| DIN EN 1402-8:2004-01 | PNSHAPED REFRACTORY PRODUCTS - PART 8: DETERMINATION OF COMPLEMENTARY PROPERTIES |
| I.S. EN 1402-8:2003 | UNSHAPED REFRACTORY PRODUCTS - PART 8: DETERMINATION OF COMPLEMENTARY PROPERTIES |
| BS EN 993-20:2004 | Methods of test for dense shaped refractory products Determination of resistance to abrasion at ambient temperature |
| I.S. EN 993-20:2004 | METHODS OF TEST FOR DENSE SHAPED REFRACTORY PRODUCTS - PART 20: DETERMINATION OF RESISTANCE TO ABRASION AT AMBIENT TEMPERATURE |
| 08/30182897 DC : DRAFT MAY 2008 | BS ISO 1927-1 - UNSHAPED REFRACTORY MATERIALS - PART 1: INTRODUCTION AND CLASSIFICATION |
| EN 1402-7:2003 | Unshaped refractory products - Part 7: Tests on pre-formed shapes |
| EN 1402-1:2003 | Unshaped refractory products - Part 1: Introduction and classification |
| EN 993-20:2004 | Methods of test for dense shaped refractory products - Part 20: Determination of resistance to abrasion at ambient temperature |
| EN 1402-8:2003 | Unshaped refractory products - Part 8: Determination of complementary properties |
| BS EN 1402-1:2003 | Unshaped refractory products Introduction and classification |
| BS EN 1402-7:2003 | Unshaped refractory products Tests on pre-formed shapes |
| EN 993-9:1997 | Methods of testing dense shaped refractory products - Part 9: Determination of creep in compression |
| ISO 2477:2005 | Shaped insulating refractory products — Determination of permanent change in dimensions on heating |
| EN 1402-5:2003 | Unshaped refractory products - Part 5: Preparation and treatment of test pieces |
| EN 993-7:1998 | Methods of test for dense shaped refractory products - Part 7: Determination of modulus of rupture at elevated temperatures |
| EN 1094-5 : 1995 | INSULATING REFRACTORY PRODUCTS - PART 5: DETERMINATION OF COLD CRUSHING STRENGTH |
| EN 993-5:1998 | Methods of test for dense shaped refractory products - Part 5: Determination of cold crushing strength |
| EN 993-8 : 1997 | METHODS OF TESTING DENSE SHAPED REFRACTORY PRODUCTS - PART 8: DETERMINATION OF REFRACTORINESS-UNDER-LOAD |
| EN 1402-1:2003 | Unshaped refractory products - Part 1: Introduction and classification |
| EN 1094-4:1995 | Insulating refractory products - Part 4: Determination of bulk density and true porosity |
| EN 1094-6:1998 | Insulating refractory products - Part 6: Determination of permanent change in dimensions of shaped products on heating (ISO 2477:1987 modified) |
| EN 993-6:1995 | Methods of test for dense shaped refractory products - Part 6: Determination of modulus of rupture at ambient temperature |
| EN 993-1:1995 | Methods of test for dense shaped refractory products - Part 1: Determination of bulk density, apparent porosity and true porosity |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.