EN 12753:2005+A1:2010
Current
The latest, up-to-date edition.
Thermal cleaning systems for exhaust gas from surface treatment equipment - Safety requirements
26-05-2010
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
6 Verification of the safety requirements and/or protective
measures
7 Information for use
Annex A (informative) Schematic views of thermal
cleaning systems
Annex B (informative) Temperature dependency of LEL
Annex C (informative) Operating parameters, conditions for
use and measurement methods
Annex D (informative) Guidelines for thermal cleaning
systems operating at increased
concentrations
Annex E (informative) References to national exposure limit
values
Annex F (normative) Classification of material's reaction
to the fire - national standards
Annex G (informative) Relation between categories and zones
Annex ZA (informative) Relationship between this European
Standard and the Essential
Requirements of EC Directive 2006/42/EC
Bibliography
This European Standard is applicable to thermal cleaning systems for exhaust gas from surface treatment equipment/systems as given below in which the concentration of exhaust gas to be cleaned (for the purpose of this European Standard, named "process gas") at the inlet to the thermal cleaning system is safely limited within the concentration ranges given in 5.2.2.2.Surface treatment equipment includes:-dryers according to EN 1539, curing equipment;-flash-off areas;-coating plants (e.g. closed spray booths, open fronted spray booths);-machines using flammable solvents for the pre-treatment and cleaning of products or equipment (e.g. barrels, tins, cans or containers);-related solvent handling equipment.This European Standard deals only with the significant hazards from fire and explosion and hazards generated by residual process gases as listed in Clause 4, when used as intended and under the conditions foreseen by the manufacturer.The types of thermal cleaning systems covered in this European Standard are-direct combustion, and-catalytic combustion(see definitions in 3.1.1 and 3.1.2).This European Standard applies in conjunction with the relevant requirements of EN 746-1 and EN 746-2.For the purpose of this European Standard a thermal cleaning system for process gas contains the following components: fan(s), heat exchanger, process space, main and supporting burner, injection system, power driven dampers, control and power circuits joined together for the processing of flammable substances, predominantly volatile organic compounds, by effecting oxidation.NOTE Thermal cleaning equipment is usually integrated with systems as covered by e.g. EN 1010-1, EN 1539, EN 12215, EN 12921-1 or EN 12921-3.1.2This European Standard is not applicable to:-thermal paint removal systems;-pyrolytic systems.
DevelopmentNote |
2005 Edition Re-issued in May 2010 & incorporates AMD 1 2010. (06/2010)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Current
|
Standards | Relationship |
SN EN 12753 : 2005 + A1 2010 | Identical |
DIN EN 12753:2011-02 | Identical |
UNI EN 12753 : 2010 | Identical |
PN EN 12753 : 2007 + A1 2012 | Identical |
NF EN 12753 : 2005 + A1 2010 | Identical |
NS EN 12753 : 2005 + A1 2010 | Identical |
BS EN 12753 : 2005 | Identical |
NBN EN 12753 : 2005 + A1 2010 | Identical |
I.S. EN 12753:2005 | Identical |
NEN EN 12753 : 2005 + A1 2010 | Identical |
UNE-EN 12753:2006 | Identical |
UNE-EN 12753:2006+A1:2010 | Identical |
BS EN 12753:2005+A1:2010 | Identical |
ISO 12643-1:2009 | Graphic technology — Safety requirements for graphic technology equipment and systems — Part 1: General requirements |
DIN EN 13355:2010-06 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
BS EN 14462:2015 | Surface treatment equipment. Noise test code for surface treatment equipment including its ancillary handling equipment. Accuracy grades 2 and 3 |
EN 13355:2004+A1:2009 | Coating plants - Combined booths - Safety requirements |
PREN 14462 : DRAFT 2012 | SURFACE TREATMENT EQUIPMENT - NOISE TEST CODE FOR SURFACE TREATMENT EQUIPMENT INCLUDING ITS ANCILLARY HANDLING EQUIPMENT - ACCURACY GRADES 2 AND 3 |
ISO 12649:2004 | Graphic technology Safety requirements for binding and finishing systems and equipment |
BS EN 13355 : 2004 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
I.S. EN 13355:2005 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
I.S. EN 14462:2015 | SURFACE TREATMENT EQUIPMENT - NOISE TEST CODE FOR SURFACE TREATMENT EQUIPMENT INCLUDING ITS ANCILLARY HANDLING EQUIPMENT - ACCURACY GRADES 2 AND 3 |
VDI 3476 Blatt 1:2015-06 | Waste gas cleaning - Methods of catalytic waste gas cleaning - Fundamentals |
VDI 2441:2016-05 | Process gas and waste gas cleaning by cold plasma - Barrier discharge, corona discharge, UV radiation |
VDI 3456:2009-12 | Emission control - Refinishing and finishing of vehicles |
BS ISO 12648:2006 | Graphic technology. Safety requirements for printing press systems |
DIN EN 14462:2015-08 | SURFACE TREATMENT EQUIPMENT - NOISE TEST CODE FOR SURFACE TREATMENT EQUIPMENT INCLUDING ITS ANCILLARY HANDLING EQUIPMENT - ACCURACY GRADES 2 AND 3 |
UNI EN 13355 : 2009 | COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS |
BS ISO 12643-1:2009 | Graphic technology. Safety requirements for graphic technology equipment and systems General requirements |
08/30190505 DC : 0 | BS ISO 12643-1 - GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR GRAPHIC TECHNOLOGY EQUIPMENT AND SYSTEMS - PART 1: GENERAL REQUIREMENTS |
ISO 12648:2006 | Graphic technology Safety requirements for printing press systems |
EN 14462:2015 | Surface treatment equipment - Noise test code for surface treatment equipment including its ancillary handling equipment - Accuracy grades 2 and 3 |
12/30272422 DC : 0 | BS EN 14462 - SURFACE TREATMENT EQUIPMENT - NOISE TEST CODE FOR SURFACE TREATMENT EQUIPMENT INCLUDING ITS ANCILLARY HANDLING EQUIPMENT - ACCURACY GRADES 2 AND 3 |
BS ISO 12649:2004 | Graphic technology. Safety requirements for binding and finishing systems and equipment |
ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
EN 1539:2015 | Dryers and ovens, in which flammable substances are released - Safety requirements |
IEC 60079-1:2014 RLV | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
EN 746-1:1997+A1:2009 | Industrial thermoprocessing equipment - Part 1: Common safety requirements for industrial thermoprocessing equipment |
IEC 60079-10:2002 | Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas |
EN 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements |
EN 746-2:2010 | Industrial thermoprocessing equipment - Part 2: Safety requirements for combustion and fuel handling systems |
EN 60079-1:2014 | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
EN 13113:2002+A1:2010 | Tannery machines - Roller coating machines - Safety requirements |
EN 971-1 : 1996 | PAINTS AND VARNISHES - TERMS AND DEFINITIONS FOR COATING MATERIALS - PART 1: GENERAL TERMS |
IEC 60079-19:2010+AMD1:2015 CSV | Explosive atmospheres - Part 19: Equipment repair, overhaul and reclamation |
EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
EN 50020:2002 | Electrical apparatus for potentially explosive atmospheres - Intrinsic safety 'i' |
EN 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
EN 13463-1:2009 | Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements |
EN 12874 : 2001 | FLAME ARRESTERS - PERFORMANCE REQUIREMENTS, TEST METHODS AND LIMITS FOR USE |
EN 13478:2001+A1:2008 | Safety of machinery - Fire prevention and protection |
EN 61779-4:2000 | Electrical apparatus for the detection and measurement of flammable gases - Part 4: Performance requirements for group II apparatus indicating a volume fraction up to 100 % lower explosive limit |
IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
IEC 60079-18:2014 RLV | Explosive atmospheres - Part 18: Equipment protection by encapsulation “m” |
EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
EN 50017:1998 | Electrical apparatus for potentially explosive atmospheres - Powder filling "q" |
EN 12215:2004+A1:2009 | Coating plants - Spray booths for application of organic liquid coating materials - Safety requirements |
EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
EN 60519-1:2015 | Safety in installations for electroheating and electromagnetic processing - Part 1: General requirements |
ISO 11690-2:1996 | Acoustics Recommended practice for the design of low-noise workplaces containing machinery Part 2: Noise control measures |
EN 619:2002+A1:2010 | Continuous handling equipment and systems - Safety and EMC requirements for equipment for mechanical handling of unit loads |
EN 12921-1:2005+A1:2010 | Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 1: Common safety requirements |
IEC 61779-4:1998 | Electrical apparatus for the detection and measurement of flammable gases - Part 4: Performance requirements for group II apparatus indicating up to 100% lower explosive limit |
EN 1010-1:2004+A1:2010 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements |
NFPA 86 : 2015 | OVENS AND FURNACES |
EN 60079-25:2010/AC:2013 | EXPLOSIVE ATMOSPHERES - PART 25: INTRINSICALLY SAFE ELECTRICAL SYSTEMS (IEC 60079-25:2010) |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
EN 746-3:1997+A1:2009 | Industrial thermoprocessing equipment - Part 3: Safety requirements for the generation and use of atmosphere gases |
EN 12921-3:2005+A1:2008 | Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 3: Safety of machines using flammable cleaning liquids |
ISO 11690-1:1996 | Acoustics Recommended practice for the design of low-noise workplaces containing machinery Part 1: Noise control strategies |
IEC 60079-25:2010 | Explosive atmospheres - Part 25: Intrinsically safe electrical systems |
IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
EN 60079-10:2003 | Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas |
ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
IEC 60079-14:2013 | Explosive atmospheres - Part 14: Electrical installations design, selection and erection |
EN 61779-1 : 2000 AMD 11 2004 | ELECTRICAL APPARATUS FOR THE DETECTION AND MEASUREMENT OF FLAMMABLE GASES - PART 1: GENERAL REQUIREMENTS AND TEST METHODS |
EN ISO 11690-2 : 1996 | ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE WORKPLACES CONTAINING MACHINERY - NOISE CONTROL MEASURES |
EN 60079-14:2014/AC:2016 | EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016) |
EN 954-1 : 1996 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
EN 12198-1:2000+A1:2008 | Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 1: General principles |
PREN 14986 : DRAFT 2014 | DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
EN 50073:1999 | Guide for selection, installation, use and maintenance of apparatus for the detection and measurement of combustible gases or oxygen |
EN 50015:1998 | Electrical apparatus for potentially explosive atmospheres - Oil immersion "o" |
EN 13463-5:2011 | Non-electrical equipment intended for use in potentially explosive atmospheres - Part 5: Protection by constructional safety 'c' |
IEC 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508) |
EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
IEC 61779-1:1998 | Electrical apparatus for the detection and measurement of flammable gases - Part 1: General requirements and test methods |
EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
IEC 60519-1:2015 | Safety in installations for electroheating and electromagnetic processing - Part 1: General requirements |
ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
EN ISO 11690-1 : 1996 | ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE WORKPLACES CONTAINING MACHINERY - NOISE CONTROL STRATEGIES |
IEC 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
EN 60079-2:2014/AC:2015 | EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.