EN 12102:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Air conditioners, liquid chilling packages, heat pumps and dehumidifiers with electrically driven compressors for space heating and cooling - Measurement of airborne noise - Determination of the sound power level
01-11-2017
31-07-2013
Foreword
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Measuring instruments
5 Operation of the unit
6 Installation
7 Acoustic measurement methods
8 Uncertainty of measurement results
9 Test report
Annex A (normative) - Specific measurement for
variable speed units
Annex ZA (informative) - Relationship between this
European Standard and the requirements of
Commission Regulation (EC) No 206/2012
Bibliography
This European Standard establishes requirements for determining, in accordance with a standardized procedure, the sound power level emitted into the surrounding air by air conditioners, heat pumps, liquid chilling packages with electrically driven compressors when used for space heating and/or cooling, including water cooled multisplit systems, as described in EN 14511 and dehumidifiers as described in EN 810.This European Standard also covers the measurement of the sound power level of evaporatively-cooled condenser air conditioners, as defined in EN 15218. However, the measurement should be done without external water feeding and these units will thus be considered as the other air conditioners covered by EN 14511. It is emphasised that this measurement standard only refers to airborne noise. This European Standard offers ways to determine the sound power level of units. Some of them are specifically adapted to provide results with low uncertainties, by using laboratory class acoustic methods and highly controlled working conditions. Those measurements are suitable for certification, labelling and marking purposes. In some cases, the target and/or the environment of the measurements do not allow such precision-class methods. This European Standard also offers ways to assess sound power levels with acceptable accuracy even though acoustic methods and/or working conditions are not laboratory-type, e.g. in situ or quality control measurements.This European Standard gives two classes of measurements and results, according to the test environment: -Class A measurements correspond to controlled working conditions (standard or application rating conditions). It is defined by the respect to the tolerances of Table 2 and should be used for the conformity to requirements of the Commission Regulation (EC) No 206/2012 of 6 March 2012 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for air conditioners-Class B measurements correspond to the case where the range defined by the tolerances of Table 2 cannot be fulfilled.In both classes, precision or engineering class acoustic methods should be applied. The choice of the acoustic measurement method is done in accordance with EN ISO 3740 and EN ISO 9614 depending on the type of surrounding acoustic fields (diffuse or free field, enclosed or open space), and the available instrumentation. Whatever the current working conditions, the reference of acoustic standard should be reported, with explicit mention of its accuracy class.The use of EN ISO 3746 and EN ISO 3747 as survey grade methods are not recommended due to the high level of uncertainties. Their use is only allowed for non controlled environments.Three methods for determining the sound power levels are specified in order to avoid unduly restricting existing facilities and experience:-the first methodology is based on reverberation room measurement (see EN ISO 3741, EN ISO 3743 and EN ISO 3747 in some favourable cases when the engineering grade can be fulfilled); -the second method is based on measurements in an essentially free field over a reflecting plane (see EN ISO 3744 and EN ISO 3745); -the third method is based on sound intensity measurement (see EN ISO 9614) in preferably free field environment.The references in this European Standard to EN ISO 3743 should be understood as EN ISO 3743-1 or EN ISO 3743-2 as well.The necessity to regulate the test conditions obviously leads to recommend test methods implemented in acoustically designed (enclosed) spaces, such as EN ISO 3741, EN ISO 3743, EN ISO 3745 and also EN ISO 9614 when implemented in an enclosed space. The open spaces should be covered only in specific cases, e.g. when the size or the power of the unit under test cannot be managed by standard test rooms. Suitable test methods are EN ISO 3744 and EN ISO 9614.
Committee |
CEN/TC 113
|
DevelopmentNote |
Supersedes ENV 12102. (07/2008) Supersedes PREN 12102. (08/2013)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
UNE-EN 12102:2014 | Identical |
NBN EN 12102 : 2013 | Identical |
BS EN 12102:2013 | Identical |
NEN EN 12102 : 2013 | Identical |
NS EN 12102 : 2013 | Identical |
PN EN 12102 : 2014 | Identical |
I.S. EN 12102:2013 | Identical |
UNI EN 12102 : 2014 | Identical |
NF EN 12102 : 2013 | Identical |
SN EN 12102 : 2013 | Identical |
DIN EN 12102:2013-10 | Identical |
DIN EN 15879-1:2011-05 | Testing and rating of direct exchange ground coupled heat pumps with electrically driven compressors for space heating and/or cooling - Part 1: Direct exchange-to-water heat pumps |
I.S. EN 16905-4:2017 | GAS-FIRED ENDOTHERMIC ENGINE DRIVEN HEAT PUMPS - PART 4: TEST METHODS |
15/30328744 DC : 0 | BS EN 14511-4 - AIR CONDITIONERS, LIQUID CHILLING PACKAGES AND HEAT PUMPS FOR SPACE HEATING AND COOLING AND PROCESS CHILLERS, WITH ELECTRICALLY DRIVEN COMPRESSORS - PART 4: REQUIREMENTS |
DIN EN 14511-4:2015-12 (Draft) | AIR CONDITIONERS, LIQUID CHILLING PACKAGES AND HEAT PUMPS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - PART 4: OPERATING REQUIREMENTS, MARKING AND INSTRUCTIONS |
UNI EN 14511-4 : 2013 | AIR CONDITIONERS, LIQUID CHILLING PACKAGES AND HEAT PUMPS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - PART 4: OPERATING REQUIREMENTS, MARKING AND INSTRUCTIONS |
UNI EN 13141-7 : 2011 | VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 7: PERFORMANCE TESTING OF A MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR SINGLE FAMILY DWELLINGS |
BS EN 15879-1:2011 | Testing and rating of direct exchange ground coupled heat pumps with electrically driven compressors for space heating and/or cooling Direct exchange-to-water heat pumps |
BS EN 16573:2017 | Ventilation for Buildings. Performance testing of components for residential buildings. Multifunctional balanced ventilation units for single family dwellings, including heat pumps |
I.S. EN 16573:2017 | VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS FOR RESIDENTIAL BUILDINGS - MULTIFUNCTIONAL BALANCED VENTILATION UNITS FOR SINGLE FAMILY DWELLINGS, INCLUDING HEAT PUMPS |
BS EN 16905-4:2017 | Gas-fired endothermic engine driven heat pumps Test methods |
BS EN 14511-4:2013 | Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling Operating requirements, marking and instructions |
DIN EN 16905-4:2015-10 (Draft) | GAS-FIRED ENDOTHERMIC ENGINE DRIVEN HEAT PUMPS - PART 4: TEST METHODS |
DIN EN 14511-4:2013-12 | AIR CONDITIONERS, LIQUID CHILLING PACKAGES AND HEAT PUMPS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - PART 4: OPERATING REQUIREMENTS, MARKING AND INSTRUCTIONS |
I.S. EN 13141-7:2010 | VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS/PRODUCTS FOR RESIDENTIAL VENTILATION - PART 7: PERFORMANCE TESTING OF A MECHANICAL SUPPLY AND EXHAUST VENTILATION UNITS (INCLUDING HEAT RECOVERY) FOR MECHANICAL VENTILATION SYSTEMS INTENDED FOR SINGLE FAMILY DWELLINGS |
DIN EN 13141-7:2011-01 | Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 7: Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings |
EN 13141-7:2010 | Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 7: Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings |
EN 16905-4:2017 | Gas-fired endothermic engine driven heat pumps - Part 4: Test methods |
13/30275116 DC : 0 | BS EN 16573 - VENTILATION FOR BUILDINGS - PERFORMANCE TESTING OF COMPONENTS FOR RESIDENTIAL BUILDINGS - MULTIFUNCTIONAL BALANCED VENTILATION UNITS FOR SINGLE FAMILY DWELLINGS, INCLUDING HEAT PUMPS |
NF EN 15879-1 : 2011 | TESTING AND RATING OF DIRECT EXCHANGE GROUND COUPLED HEAT PUMPS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND/OR COOLING - PART 1: DIRECT EXCHANGE-TO-WATER HEAT PUMPS |
UNE-EN 12309-4:2015 | Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 4: Test methods |
EN 14511-4:2018 | Air conditioners, liquid chilling packages and heat pumps for space heating and cooling and process chillers, with electrically driven compressors - Part 4: Requirements |
09/30206303 DC : 0 | BS EN 60335-2-40 FPRAD - HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-40: PARTICULAR REQUIREMENTS FOR ELECTRICAL HEAT PUMPS, AIR-CONDITIONERS AND DEHUMIDIFIERS |
BS EN 12309-4:2014 | Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW Test methods |
09/30206349 DC : 0 | BS EN 14511-4 - AIR CONDITIONERS, LIQUID CHILLING PACKAGES AND HEAT PUMPS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND COOLING - PART 4: REQUIREMENTS |
15/30326260 DC : 0 | BS EN 16905-4 - GAS-FIRED ENDOTHERMIC ENGINE HEAT PUMPS - PART 4: TEST METHODS |
UNI EN 15879-1 : 2011 | TESTING AND RATING OF DIRECT EXCHANGE GROUND COUPLED HEAT PUMPS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND/OR COOLING - PART 1: DIRECT EXCHANGE-TO-WATER HEAT PUMPS |
I.S. EN 14511-4:2018 | AIR CONDITIONERS, LIQUID CHILLING PACKAGES AND HEAT PUMPS FOR SPACE HEATING AND COOLING AND PROCESS CHILLERS, WITH ELECTRICALLY DRIVEN COMPRESSORS - PART 4: REQUIREMENTS |
I.S. EN 12309-4:2014 | GAS-FIRED SORPTION APPLIANCES FOR HEATING AND/OR COOLING WITH A NET HEAT INPUT NOT EXCEEDING 70 KW - PART 4: TEST METHODS |
I.S. EN 15879-1:2011 | TESTING AND RATING OF DIRECT EXCHANGE GROUND COUPLED HEAT PUMPS WITH ELECTRICALLY DRIVEN COMPRESSORS FOR SPACE HEATING AND/OR COOLING - PART 1: DIRECT EXCHANGE-TO-WATER HEAT PUMPS |
UNE-EN 14511-4:2014 | Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Part 4: Operating requirements, marking and instructions |
BS EN 60335-2-40 : 2003 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-40: PARTICULAR REQUIREMENTS FOR ELECTRICAL HEAT PUMPS, AIR-CONDITIONERS AND DEHUMIDIFIERS |
EN 15879-1:2011 | Testing and rating of direct exchange ground coupled heat pumps with electrically driven compressors for space heating and/or cooling - Part 1: Direct exchange-to-water heat pumps |
EN 12309-4:2014 | Gas-fired sorption appliances for heating and/or cooling with a net heat input not exceeding 70 kW - Part 4: Test methods |
EN 16573:2017 | Ventilation for Buildings - Performance testing of components for residential buildings - Multifunctional balanced ventilation units for single family dwellings, including heat pumps |
UNE-EN 15879-1:2011 | Testing and rating of direct exchange ground coupled heat pumps with electrically driven compressors for space heating and/or cooling - Part 1: Direct exchange-to-water heat pumps |
UNE-EN 13141-7:2011 | Ventilation for buildings - Performance testing of components/products for residential ventilation - Part 7: Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings |
BS EN 13141-7:2010 | Ventilation for buildings. Performance testing of components/products for residential ventilation Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings |
EN 60335-2-40:2003/A13:2012/AC:2013 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-40: PARTICULAR REQUIREMENTS FOR ELECTRICAL HEAT PUMPS, AIR-CONDITIONERS AND DEHUMIDIFIERS |
I.S. EN 60335-2-40:2006 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-40: PARTICULAR REQUIREMENTS FOR ELECTRICAL HEAT PUMPS, AIR-CONDITIONERS AND DEHUMIDIFIERS (IEC 60335-2-40:2002 (MOD)) |
ISO 5802:2001 | Industrial fans — Performance testing in situ |
ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
EN ISO 3743-2:2009 | Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994) |
ISO 3743-2:1994 | Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms |
ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
EN 810:1997 | Dehumidifiers with electrically driven compressors - Rating tests, marking, operational requirements and technical data sheet |
ISO 3747:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering/survey methods for use in situ in a reverberant environment |
EN ISO 3741:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Precision methods for reverberation test rooms (ISO 3741:2010) |
ISO 3740:2000 | Acoustics Determination of sound power levels of noise sources Guidelines for the use of basic standards |
ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
EN ISO 5801:2017 | Fans - Performance testing using standardized airways (ISO 5801:2017) |
ISO 5801:2017 | Fans — Performance testing using standardized airways |
ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
EN ISO 3747:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering/survey methods for use in situ in a reverberant environment (ISO 3747:2010) |
EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
ISO 9614-3:2002 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 3: Precision method for measurement by scanning |
EN ISO 3740:2000 | Acoustics - Determination of sound power levels of noise sources - Guidelines for the use of basic standards (ISO 3740:2000) |
EN ISO 9614-2:1996 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 2: Measurement by scanning (ISO 9614-2:1996) |
ENV 13005 : DRAFT 1999 | GUIDE TO THE EXPRESSION OF UNCERTAINTY IN MEASUREMENT |
EN ISO 3743-1:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010) |
EN ISO 9614-3:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 3: Precision method for measurement by scanning (ISO 9614-3:2002) |
ISO 3741:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Precision methods for reverberation test rooms |
ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
2009/125/EC : 2009 AMD 1 2012 | DIRECTIVE 2009/125/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 21 OCTOBER 2009 ESTABLISHING A FRAMEWORK FOR THE SETTING OF ECODESIGN REQUIREMENTS FOR ENERGY-RELATED PRODUCTS (RECAST) (TEXT WITH EEA RELEVANCE) |
ISO/IEC Guide 98-3:2008 | Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995) |
ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.