EN 1124-3:2008
Current
The latest, up-to-date edition.
Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 3: System X - Dimensions
01-10-2008
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Dimensions
5.1 General and tolerances
5.2 Sockets
5.3 Pipes
5.3.1 General
5.3.2 Pipe with one socket - Shape B 1
5.3.3 Pipe with two sockets - Shape B 2
5.4 Bends
5.4.1 General
5.4.2 Bend with large radius - Shape C 1
5.4.3 Bend with large radius - Shape C 2
5.4.4 Bend with small radius - Shape C 3
5.4.5 Bend with stilling section - Shape C 4
5.4.6 Bend with stilling section - Shape C 5
5.5 Branches
5.5.1 General
5.5.2 Single branch - Shape D 1
5.5.3 Reducing single branch - Shape D 11
5.5.4 Reducing double branch - Shape D 21
5.6 Connecting units
5.6.1 General
5.6.2 Connecting units for the use with discharge
sets of sanitary appliances (angular bend
90 degree) - Shape E 1
5.6.3 Connecting units for use with other kinds of
pipes
5.7 Transition pipe (concentric) - Shape F 2
5.8 Repair coupling/double socket - Shape F 4
5.9 Insertion coupling with long socket - Shape F 5
5.10 Trap - Shape G 1
5.11 Access pipes
5.11.1 General
5.11.2 Access pipe with round cleaning hole - Shape H 1
5.11.3 Access pipe with round cleaning hole - Shape H 2
5.11.4 Access pipe with rectangular cleaning hole
(R) - Shape H 3 or oval cleaning hole (O) -
Shape H 4
5.12 Shear coupling
5.12.1 General
5.12.2 Shear coupling A - Shape K 1
5.12.3 Shear coupling B - Shape K 2
5.13 Plug with screw top - Shape K 12
6 Other fittings
7 Seals
7.1 General
7.2 Seals for DN 40 to DN 200 - Shape M 1
7.3 Transition seal from steel pipe special socket
to plastic drain pipe - Shape E 12 D
7.4 Gasket for round cleaning holes of access
pipes of shape H 1 - Shape H 1 D
7.5 Gasket for rectangular cleaning holes - Shape
H 2 D or gasket for oval cleaning holes -
Shape H 3 D
This European Standard is applicable to pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for wastewater systems.It specifies dimensions and tolerances for pipes, fittings, pipe connectors and seals of the System X and establishes a system of designations for the different pipe and fitting types that conform to the stated requirements.NOTESystem X is a system of pipes and fittings of longitudinally welded stainless steel pipes with two-step sockets.This European Standard is only valid in connection with EN 1124-1. This European Standard does not apply to the marking of products. EN 1124-1/A1 applies to the marking.
| Committee |
CEN/TC 165
|
| DevelopmentNote |
To be read in conjunction with EN 1124-1. (10/2008)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| NS EN 1124-3 : 2ED 2008 | Identical |
| NBN EN 1124-3 : 2008 | Identical |
| ÖNORM EN ISO 11124-3: 2018 12 01 | Identical |
| PN EN 1124-3 : 2008 | Identical |
| UNI EN 1124-3 : 2008 | Identical |
| DIN EN 1124-3:2009-02 | Identical |
| UNE-EN 1124-3:2009 | Identical |
| BS EN 1124-3:2008 | Identical |
| SN EN 1124-3 : 2008 | Identical |
| I.S. EN 1124-3:2008 | Identical |
| NEN EN 1124-3 : 2008 | Identical |
| NF EN 1124-3 : 2008 | Identical |
| DIN EN 1124-4:2014-02 | PIPES AND FITTINGS OF LONGITUDINALLY WELDED STAINLESS STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTEWATER SYSTEMS - PART 4: COMPONENTS FOR VACUUM DRAINAGE SYSTEMS AND FOR DRAINAGE SYSTEMS ON SHIPS |
| BS EN 12380:2002 | Air admittance valves for drainage systems. Requirements, test methods and evaluation of conformity |
| EN 1124-4:2013 | Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for wastewater systems - Part 4: Components for vacuum drainage systems and for drainage systems on ships |
| UNE-EN 1124-4:2014 | Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for wastewater systems - Part 4: Components for vacuum drainage systems and for drainage systems on ships |
| I.S. EN 1124-4:2013 | PIPES AND FITTINGS OF LONGITUDINALLY WELDED STAINLESS STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTEWATER SYSTEMS - PART 4: COMPONENTS FOR VACUUM DRAINAGE SYSTEMS AND FOR DRAINAGE SYSTEMS ON SHIPS |
| PREN 1124-4 : DRAFT 2012 | PIPES AND FITTINGS OF LONGITUDINALLY WELDED STAINLESS STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTEWATER SYSTEMS - PART 4: COMPONENTS FOR VACUUM DRAINAGE SYSTEMS AND FOR DRAINAGE SYSTEMS ON SHIPS |
| UNI EN 1124-4 : 2013 | PIPES AND FITTINGS OF LONGITUDINALLY WELDED STAINLESS STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTEWATER SYSTEMS - PART 4: COMPONENTS FOR VACUUM DRAINAGE SYSTEMS AND FOR DRAINAGE SYSTEMS ON SHIPS |
| 12/30256801 DC : DRAFT FEB 2012 | BS EN 1124-4 - PIPES AND FITTINGS OF LONGITUDINALLY WELDED STAINLESS STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTEWATER SYSTEMS - PART 4: COMPONENTS FOR VACUUM DRAINAGE SYSTEMS AND FOR DRAINAGE SYSTEMS ON SHIPS |
| BS EN 1124-1:1999 | Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems Requirements, testing, quality control |
| BS EN 1124-4:2013 | Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for wastewater systems Components for vacuum drainage systems and for drainage systems on ships |
| EN 12380:2002 | Air admittance valves for drainage systems - Requirements, tests methods and evaluation of conformity |
| EN 1566-1:1998 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system |
| EN ISO 1127:1996 | Stainless steel tubes - Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992) |
| EN 1123-2:2006+A1:2007 | Pipes and fittings of longitudinally welded hot-dip galvanized steel tube with spigot and socket for waste water systems - Part 2: Dimensions |
| EN 1565-1:1998 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system |
| ISO 1127:1992 | Stainless steel tubes Dimensions, tolerances and conventional masses per unit length |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.