DIN EN ISO 527-1:2012-06
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL PRINCIPLES (ISO 527-1:2012)
Hardcopy , PDF
21-12-2019
English, German
01-01-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
National Annex NA (informative) - Bibliography
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle and methods
5 Apparatus
6 Test specimens
7 Number of test specimens
8 Conditioning
9 Procedure
10 Calculation and expression of results
11 Precision
12 Test report
Annex A (informative) - Determination of strain at yield
Annex B (informative) - Extensometer accuracy for the
determination of Poisson's ratio
Annex C (normative) - Calibration requirements for the
determination of the tensile modulus
Bibliography
Defines the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.
| DevelopmentNote |
Together with DIN EN ISO 527-2 E; supersedes DIN 53455 E. (12/1999) Supersedes DIN 53457 E (08/2002)
|
| DocumentType |
Standard
|
| Pages |
30
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNE-EN ISO 527-1:1996 | Identical |
| SN EN ISO 527-1 : 2012 | Identical |
| ONORM EN ISO 527-1 : 2012 | Identical |
| BS EN ISO 527-1:2012 | Identical |
| UNI EN ISO 527-1 : 2012 | Identical |
| EN ISO 527-1:2012 | Identical |
| NEN EN ISO 527-1 : 2012 | Identical |
| NF EN ISO 527-1 : 2012 | Identical |
| I.S. EN ISO 527-1:2012 | Identical |
| NS EN ISO 527-1 : 2012 | Identical |
| ISO 527-1:2012 | Identical |
| NBN EN ISO 527-1 : 2012 | Identical |
| DIN ISO 5355:2006-05 | ALPINE SKI-BOOTS - REQUIREMENTS AND TEST METHODS |
| DIN EN ISO 527-5:2010-01 | Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009) |
| DIN EN ISO 22007-4:2012-04 | PLASTICS - DETERMINATION OF THERMAL CONDUCTIVITY AND THERMAL DIFFUSIVITY - PART 4: LASER FLASH METHOD (ISO 22007-4:2017) |
| DIN EN ISO 11296-7:2013-05 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011) |
| DIN EN ISO 15013:2008-01 | Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2007); German version EN ISO 15013:2007 |
| DIN 34811:1999-09 | CROSS- RECESSED FLAT HEAD PLASTIC SCREWS |
| DIN EN ISO 3672-2:2002-07 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN 53504:2009-10 | TESTING OF RUBBER - DETERMINATION OF TENSILE STRENGTH AT BREAK, TENSILE STRESS AT YIELD, ELONGATION AT BREAK AND STRESS VALUES IN A TENSILE TEST |
| DIN 53363:2003-10 | Determining the tear resistance of plastic film and sheeting by the trouser tear method |
| DIN EN 12864 E : 2006 AMD 3 2010 | LOW PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| DIN EN ISO 11963:2013-03 | PLASTICS - POLYCARBONATE SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS (ISO 11963:2012) |
| DIN 34813:1999-09 | CROSS- RECESSED CHEESE HEAD PLASTIC SCREWS |
| DIN 34812:1999-09 | CROSS- RECESSED PAN HEAD PLASTIC SCREWS |
| DIN ISO 9523:2016-05 | TOURING SKI-BOOTS FOR ADULTS - INTERFACE WITH TOURING SKI-BINDINGS - REQUIREMENTS AND TEST METHODS (ISO 9523:2015) |
| DIN EN ISO 527-2:2012-06 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| DIN 30678:2013-09 | Polypropylene coatings on steel pipes and fittings - Requirements and testing |
| DIN EN ISO 12215-5:2014-10 | SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008 + AMD 1:2014) |
| ISO 23529:2016 | Rubber General procedures for preparing and conditioning test pieces for physical test methods |
| ISO 1926:2009 | Rigid cellular plastics Determination of tensile properties |
| ISO 9513:2012 | Metallic materials — Calibration of extensometer systems used in uniaxial testing |
| ISO 2602:1980 | Statistical interpretation of test results Estimation of the mean Confidence interval |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| ISO 20753:2008 | Plastics Test specimens |
| DIN EN ISO 291:2008-08 | PLASTICS - STANDARD ATMOSPHERES FOR CONDITIONING AND TESTING |
| ISO 16012:2015 | Plastics Determination of linear dimensions of test specimens |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.