DIN EN ISO 15876-2:2004-03
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 2: PIPES
Hardcopy , PDF
07-03-2021
01-01-2004
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 Material
4.1 Pipe material
4.2 Evaluation of Sigma[LCL]-values
4.3 Influence on water intended for human consumption
5 General characteristics
5.1 Appearance
5.2 Opacity
6 Geometrical characteristics
6.1 General
6.2 Dimensions of pipes
7 Mechanical characteristics
8 Physical and chemical characteristics
9 Performance requirements
10 Marking
10.1 General requirements
10.2 Minimum required marking
Annex A (informative) Derivation of S[calc,max]
A.1 General
A.2 Design stress
A.3 Derivation of maximum value of Scalc (Scalc,max)
A.4 Use of Scalc,max to determine wall thickness
Bibliography
Specifies the characteristics of pipes made of polybutylene (PB) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption, and for heating systems, under design pressures and temperatures appropriate to the class of application.
| DevelopmentNote |
Suspended until publication of a revised English text, due to a new German edition. (06/2017)
|
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NEN EN ISO 15876-2 : 2017 | Identical |
| UNE-EN ISO 15876-2:2017 | Identical |
| UNI EN ISO 15876-2 : 2008 | Identical |
| I.S. EN ISO 15876-2:2017 | Identical |
| EN ISO 15876-2:2017 | Identical |
| ISO 15876-2:2017 | Identical |
| NBN EN ISO 15876-2 : 2004 AMD 1 2007 | Identical |
| SN EN ISO 15876-2 : 2017 | Identical |
| NS EN ISO 15876-2 : 2017 | Identical |
| BS EN ISO 15876-2:2017 | Identical |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN 743 : 1994 | PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF THE LONGITUDINAL REVERSION |
| EN ISO 15876-5:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2017) |
| EN ISO 9080:2012 | Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012) |
| EN 578 : 1993 | PLASTICS PIPING SYSTEMS - PLASTICS PIPES AND FITTINGS - DETERMINATION OF THE OPACITY |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| EN ISO 15876-1:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 1: General (ISO 15876-1:2017) |
| EN 921:1994/AC:1995 | PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE |
| EN ISO 13760:1998 | Plastics pipes for the conveyance of fluids under pressure - Miner's rule - Calculation method for cumulative damage (ISO 13760:1998) |
| ENV 12108:2001 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| EN ISO/TS 15876-7 : 2003 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| EN ISO 15876-3:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings (ISO 15876-3:2017) |
| ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.