DIN EN 792-3:2009-12
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 3: DRILLS AND TAPPERS
Hardcopy , PDF
01-03-2011
English
01-01-2009
Vorwort
Einleitung
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe
4 Liste der Gefährdungen
5 Sicherheitsanforderungen und/oder Massnahmen
6 Benutzerinformation
7 Prüfung
Anhang A (informativ) Beispiele von Bohrmaschinen und
Gewindeschneider, die in den Anwendungsbereich
dieser Norm fallen
Anhang B (informative) Symbole für Schilder und Zeichen
Anhang ZA (informativ) Zusammenhang zwischen dieser
Europäischen Norm und den grundlegenden
Anforderungen der EG-Richtlinie 98/37/EG
Anhang ZB (informativ) Zusammenhang zwischen dieser
Europäischen Norm und den grundlegenden
Anforderungen der EG-Richtlinie 2006/42/EG
Literaturhinweise
Applicable to hand-held non-electric power tools driven by rotary or linear motors, powered by compressed air, hydraulic fluid and intended to be used by one operator and supported by: - the operator's hand or hands, - a suspension, e.g. a balancer.
DocumentType |
Standard
|
Pages |
22
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
EN 792-3:2000+A1:2008 | Identical |
NS EN 792-3 : 2000 + A1 2008 | Identical |
NBN EN 792-3 : 2000 + A1 2009 | Identical |
UNE-EN 792-3:2001 | Identical |
SN EN 792-3 : 2000 + A1 2008 | Identical |
BS EN 792-3 : 2000 | Identical |
NF EN 792-3 : 2000 + A1 2008 | Identical |
I.S. EN 792-3:2000 | Identical |
UNI EN 792-3 : 2008 | Identical |
NEN EN 792-3 : 2000 + A1 2008 | Identical |
BWB TL 5130-0124 : 4ED 2009 | PNEUMATIC DRILL FOR BITS WITH A DIAMETER OF UP TO 8 MM WITH ACCESSORIES IN A STOWAGE CONTAINER |
BWB TL 5130-0161 : 1ED 2008 | PNEUMATIC DRILL 1,000 MIN-1, WITH DUST SUCTION, IN STORAGE BOX |
BWB TL 5130-0160 : 1ED 2007 | PNEUMATIC ANGLE DRILL, WITH AN ANGLED HEAD OF 90 DEGREES AND COLLET CHUCKS (1.6 TO 4.8 MM) |
BWB TL 5130-0055 : 10ED 2006 | PNEUMATIC DRILL FOR BITS WITH A DIAMETER OF UP TO 6 MM WITH ACCESSORIES IN A STOWAGE CASE |
EN 12096:1997 | Mechanical vibration - Declaration and verification of vibration emission values |
EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
EN ISO 11690-3:1998 | Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 3: Sound propagation and noise prediction in workrooms (ISO/TR 11690-3:1997) |
IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
EN 61310-2:2008 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
EN ISO 15744:2008 | Hand-held non-electric power tools - Noise measurement code - Engineering method (grade 2) (ISO 15744:2002) |
EN 50144-1 : 98 COR 2005 | SAFETY OF HAND-HELD ELECTRIC MOTOR OPERATED TOOLS - PART 1: GENERAL REQUIREMENTS |
EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
EN 292-1 : 1991 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY |
CR 1030-1:1995 | Hand-arm vibration - Guidelines for vibration hazards reduction - Part 1: Engineering methods by design of machinery |
EN 563:1994/A1:1999/AC:2000 | SAFETY OF MACHINERY - TEMPERATURES OF TOUCHABLE SURFACES - ERGONOMICS DATA TO ESTABLISH TEMPERATURE LIMIT VALUES FOR HOT SURFACES |
ISO 2787:1984 | Rotary and percussive pneumatic tools — Performance tests |
ISO 3857-1:1977 | Compressors, pneumatic tools and machines — Vocabulary — Part 1: General |
EN 28662-1:1992 | Hand-held portable power tools - Measurement of vibrations at the handle - Part 1: General (ISO 8662-1:1988) |
EN ISO 11690-2:1996 | Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 2: Noise control measures (ISO 11690-2:1996) |
EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
ISO 8662-1:1988 | Hand-held portable power tools Measurement of vibrations at the handle Part 1: General |
IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
ISO 5391:2003 | Pneumatic tools and machines Vocabulary |
ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
ISO 15744:2002 | Hand-held non-electric power tools Noise measurement code Engineering method (grade 2) |
EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
EN 1070 : 1998 | SAFETY OF MACHINERY - TERMINOLOGY |
ISO 3857-3:1989 | Compressors, pneumatic tools and machines — Vocabulary — Part 3: Pneumatic tools and machines |
EN ISO 11690-1:1996 | Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 1: Noise control strategies (ISO 11690-1:1996) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.