DIN EN 15092:2008-09
Current
The latest, up-to-date edition.
BUILDING VALVES - INLINE HOT WATER SUPPLY TEMPERING VALVES - TESTS AND REQUIREMENTS
Hardcopy , PDF
English
01-01-2008
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Vorwort
Einleitung
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe
4 Werkstoffe und Oberflächenbeschaffenheit
4.1 Allgemeines
4.2 Art der Werkstoffe
5 Anforderungen an die Ausführung und an die Masse
5.1 Rückflussverhinderer
5.2 Masse
5.3 Regelung der Einstelltemperatur
5.4 Temperatur-Entsperrfunktion
6 Mechanische Prüfungen und Anforderungen
6.1 Prüfung der Gehäusefestigkeit
6.2 Biegemomentprüfung für thermostatische Mischer
6.3 Drehmomentprüfungen für Temperaturstopps
7 Funktionsprüfungen und Anforderungen
7.1 Allgemeines
7.2 Standard-Prüfbedingungen
7.3 Überprüfung der Temperatureinstellungen von
Armaturen
7.4 Bestimmung des Mindestdurchflusses
7.5 Prüfung der Temperaturbeständigkeit, ausgehend von
der Umgebungstemperatur
7.6 Prüfung der Temperaturbeständigkeit bei wechselnden
Durchflüssen
7.7 Prüfung der Temperatursicherung bei einem Ausfall der
Kaltwasserzuleitung
7.8 Prüfung der Temperaturbeständigkeit bei veränderlichem
Eingangsdruck
7.9 Prüfung der Temperaturregelstabilität bei veränderlicher
Eingangstemperatur
7.10 Prüfung der Dauerfestigkeit des Thermostats
8 Prüfungen des Geräuschverhaltens und Anforderungen
8.1 Allgemeines
8.2 Prüfverfahren
8.3 Angabe der Ergebnisse
8.4 Anforderungen
9 Klassifizierung
10 Bezeichnung
11 Kennzeichnung
11.1 Temperatur
11.2 Durchfluss
11.3 Identifizierung
12 Einbau- und Bedienungsanleitungen
Anhang A (normativ) Einrichtung für die Prüfung der
Dauerfestigkeit des Thermostaten
Anhang B (normativ) Einrichtung für die Prüfung der
Funktionsfähigkeit
Anhang C (normativ) Messung von Kennwerten
Anhang D (informativ) Anforderungen an die Übergangstemperatur
Literaturhinweise
Describes dimensions, materials and performance requirements (including methods of test) for in line hot water supply tempering valves for sanitary hot water systems, of nominal sizes from DN 15 to DN 50.
| DocumentType |
Standard
|
| Pages |
32
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Current
|
| Standards | Relationship |
| EN 15092:2008 | Identical |
| ISO 3822-1:1999 | Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement |
| EN 1254-3:1998 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
| EN 1254-5:1998 | Copper and copper alloys - Plumbing fittings - Part 5: Fittings with short ends for capillary brazing to copper tubes |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| EN 1254-1:1998 | Copper and copper alloys - Plumbing fittings - Part 1: Fittings with ends for capillary soldering or capillary brazing to copper tubes |
| EN 1254-2:1998 | Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes |
| EN 1717:2000 | Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN 806-2:2005 | Specification for installations inside buildings conveying water for human consumption - Part 2: Design |
| ISO 6509:1981 | Corrosion of metals and alloys Determination of dezincification resistance of brass |
| EN 13959:2004 | Anti-pollution check valves - DN 6 to DN 250 inclusive family E, type A, B, C and D |
| EN 12164:2016 | Copper and copper alloys - Rod for free machining purposes |
| ISO 3822-3:1997 | Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 3: Mounting and operating conditions for in-line valves and appliances |
| EN ISO 6509:1995 | Corrosion of metals and alloys - Determination of dezincification resistance of brass (ISO 6509:1981) |
| EN 12165:2016 | Copper and copper alloys - Wrought and unwrought forging stock |
| EN 1982:2017 | Copper and copper alloys - Ingots and castings |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| EN 248:2002 | Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr |
| EN 13828:2003 | Building valves - Manually operated copper alloy and stainless steel ball valves for potable water supply in buildings -Tests and requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.