DIN EN 14399-10:2016-01 (Draft)
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD
Hardcopy , PDF
07-03-2021
German
01-01-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Vorwort
Einleitung
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe
4 Schrauben
4.1 Masse der Schrauben
4.2 Technische Lieferbedingungen für Schrauben und
Bezugsnormen
4.3 Kennzeichnung von Schrauben
5 Muttern
5.1 Masse von Muttern
5.2 Technische Lieferbedingungen für Muttern und
Bezugsnormen
5.3 Prüfkräfte für Muttern
5.4 Abkohlung des Mutterngewindes
5.5 Kennzeichnung der Muttern
6 Bezeichnung der Garnitur aus Schraube und
Mutter
7 Zugehörige Scheiben
8 Gebrauchseigenschaften der Garnitur aus Schraube,
Mutter und Scheibe
8.1 Allgemeines
8.2 Prüfung der Eignung zum Vorspannen
8.3 Prüfung der Eignung für die kalibrierte Vorspannung
8.4 Anforderungen
Literaturhinweise
Bilder
Tabellen
This standard is included in DIN Handbook 362.
| DevelopmentNote |
Applies in conjunction with DIN EN 14399-1 issue 06-2006. (07/2009) DRAFT 2016 issued in January 2016. (01/2016)
|
| DocumentType |
Draft
|
| Pages |
57
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| EN 14399-10:2018 | Identical |
| KTA 3401.2 : 2016(R2017) | STEEL CONTAINMENT VESSELS - PART 2: ANALYSIS AND DESIGN |
| ISO 272:1982 | Fasteners — Hexagon products — Widths across flats |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| EN 14399-3:2015 | High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies |
| ISO 10684:2004 | Fasteners — Hot dip galvanized coatings |
| ISO 965-5:1998 | ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing |
| ISO 4759-1:2000 | Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C |
| ISO 6157-1:1988 | Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements |
| EN 26157-1:1991 | Fasteners - Surface discontinuities - Part 1: Bolts, screws and studs for general requirements (ISO 6157-1:1988) |
| ISO 965-2:1998 | ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
| EN ISO 4759-1:2000 | Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts - Product grades A, B and C (ISO 4759-1:2000) |
| EN ISO 3269:2000 | FASTENERS - ACCEPTANCE INSPECTION |
| EN 14399-6:2015 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| EN 14399-1:2015 | High-strength structural bolting assemblies for preloading - Part 1: General requirements |
| ISO 888:2012 | Fasteners — Bolts, screws and studs — Nominal lengths and thread lengths |
| EN 14399-4:2015 | High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| ISO 261:1998 | ISO general purpose metric screw threads — General plan |
| EN 1090-2:2008+A1:2011 | Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures |
| ISO 6157-2:1995 | Fasteners Surface discontinuities Part 2: Nuts |
| EN ISO 6157-2:2004 | Fasteners - Surface discontinuities - Part 2: Nuts (ISO 6157-2:1995) |
| EN 14399-5:2015 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| ISO 3269:2000 | Fasteners Acceptance inspection |
| EN 14399-2:2015 | High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.