DIN EN 14071:2015-08
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
LPG EQUIPMENT AND ACCESSORIES - PRESSURE RELIEF VALVES FOR LPG PRESSURE VESSELS - ANCILLARY EQUIPMENT
Hardcopy , PDF
07-03-2021
English, German
01-01-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Operating conditions
5 Materials
6 Design
7 Testing of the design
8 Production testing of isolating devices and PRV
manifolds
9 Marking and labelling
10 User instructions
Annex A (normative) - Dimensions of master test
pieces for PRV and isolating devices
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 97/23/EC for
pressure equipment
Bibliography
Defines the design, testing and inspection requirements for pressure relief valve isolating devices, valve manifolds, vent pipes and system assemblies which are, where necessary, used with pressure relief valves for use in static pressure vessels for Liquefied Petroleum Gas (LPG) service.
| DevelopmentNote |
DRAFT AMD 1 issued in November 2017. (11/2017)
|
| DocumentType |
Standard
|
| Pages |
27
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Supersedes |
| Standards | Relationship |
| NF EN 14071 : 2015 | Identical |
| NS EN 14071 : 2004 | Identical |
| SN EN 14071 : 2015 | Identical |
| EN 14071:2015 | Identical |
| UNE-EN 14071:2015 | Identical |
| BS EN 14071:2015 | Identical |
| I.S. EN 14071:2015 | Identical |
| NBN EN 14071 : 2015 | Identical |
| NEN EN 14071 : 2015 | Identical |
| ONORM EN 14071 : 2015 | Identical |
| EN 14071:2015+A1:2019 | Identical |
| UNI EN 14071 : 2005 | Identical |
| PREN 14071 : DRAFT 2012 | Identical |
| EN ISO 14021:2016 | Environmental labels and declarations - Self-declared environmental claims (Type II environmental labelling) (ISO 14021:2016) |
| ISO 11114-1:2012 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials |
| EN 1503-4:2016 | Valves - Materials for bodies, bonnets and covers - Part 4: Copper alloys specified in European Standards |
| EN 10270-3:2011 | Steel wire for mechanical springs - Part 3: Stainless spring steel wire |
| EN 13906-1:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs |
| EN 14129:2014 | LPG Equipment and accessories - Pressure relief valves for LPG pressure vessels |
| ISO 14024:1999 | Environmental labels and declarations Type I environmental labelling Principles and procedures |
| EN 1503-2:2000 | Valves - Materials for bodies, bonnets and covers - Part 2: Steels other than those specified in European Standards |
| ISO 14021:2016 | Environmental labels and declarations — Self-declared environmental claims (Type II environmental labelling) |
| EN 751-2:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds |
| EN 1503-1:2000 | Valves - Materials for bodies, bonnets and covers - Part 1: Steels specified in European Standards |
| EN 13480-3:2017 | Metallic industrial piping - Part 3: Design and calculation |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| EN ISO 14025:2010 | Environmental labels and declarations - Type III environmental declarations - Principles and procedures (ISO 14025:2006) |
| ISO 11114-2:2013 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials |
| DIN 50916-1:1976-08 | Testing of copper alloys; stress corrosion cracking test in ammonia, testing of tubes, rods and profiles |
| EN ISO 11114-2:2013 | Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2013) |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 751-1:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN 12164:2016 | Copper and copper alloys - Rod for free machining purposes |
| ISO 14025:2006 | Environmental labels and declarations — Type III environmental declarations — Principles and procedures |
| EN 12420:2014 | Copper and copper alloys - Forgings |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| EN 12165:2016 | Copper and copper alloys - Wrought and unwrought forging stock |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 6957:1988 | Copper alloys Ammonia test for stress corrosion resistance |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.