DIN EN 13611:2016-09
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS
Available format(s)
Hardcopy , PDF
Superseded date
03-06-2019
Superseded by
Language(s)
English, German
Published date
01-01-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Test conditions and uncertainty of measurements
6 Design and construction
7 Performance
8 Electrical requirements
9 Electromagnetic compatibility (EMC)
10 Marking, installation and operating instructions
Annex A (informative) - Abbreviations and Symbols
Annex B (informative) - Leak-tightness tests for gas
controls - volumetric method
Annex C (informative) - Leak-tightness tests for gas
controls - pressure loss method
Annex D (normative) - Calculation of pressure loss into
leakage rate
Annex E (normative) - Electrical/electronic component
fault modes
Annex F (normative) - Additional requirements for safety
accessories and pressure accessories as defined in
EU Directive 97/23/EC
Annex G (normative) - Materials for pressurized parts
Annex H (normative) - Additional materials for pressurized
parts
Annex I (normative) - Requirements for controls used in DC
supplied burners and appliances burning gaseous or
liquid fuels
Annex J (normative) - Method for the determination of a
Safety integrity level (SIL)
Annex K (normative) - Method for the determination of a
Performance Level (PL)
Annex L (informative) - Relationship between Safety Integrity
Level (SIL) and Performance Level (PL)
Annex M (normative) - Reset functions
Annex N (informative) - Guidance document on
Environmental Aspects
Annex O (normative) - Seals of elastomer, cork and
synthetic fibre mixtures
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2009/142/EC
Annex ZB (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 97/23/EC
Bibliography
This standard is included in DIN Handbook 130.
| DevelopmentNote |
Supersedes DIN 3391. (02/2003) DRAFT 2017 issued in November 2017. (11/2017)
|
| DocumentType |
Standard
|
| Pages |
153
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN 13611 : 2016 | Identical |
| SN EN 13611 : 2015 COR 2016 | Identical |
| I.S. EN 13611:2015 | Identical |
| NF EN 13611 : 2016 | Identical |
| UNE-EN 13611:2016 | Identical |
| NBN EN 13611 : 2015 COR 2016 | Identical |
| BS EN 13611:2015 | Identical |
| NS EN 13611 : 2015 AC 2016 | Identical |
| NEN EN 13611 : 2015 AMD 1 2016 | Identical |
| UNI EN 13611 : 2011 | Identical |
| DIN HDBK 130 : 7ED 2016 | |
| VDE 0700-450 : 2001 | ELECTRICAL EQUIPMENT OF NON-ELECTRIC APPLIANCES FOR HOUSEHOLD AND SIMILAR PURPOSES - SAFETY REQUIREMENTS |
| DIN HDBK 251 : 2ED 2013 | SICHERHEITS- UND REGELEINRICHTUNGEN FUER BRENNER UND BRENNSTOFFGERAETE FUER GASFOERMIGE BRENNSTOFFE |
| EN 61508-6:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 6: Guidelines on the application of IEC 61508-2 and IEC 61508-3 |
| DIN EN 14459:2016-02 | Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Methods for classification and assessment |
| EN 10293:2015 | Steel castings - Steel castings for general engineering uses |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| EN 61508-3:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 3: Software requirements |
| ISO 9606-4:1999 | Approval testing of welders — Fusion welding — Part 4: Nickel and nickel alloys |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| EN 60747-5-2:2001/A1:2002 | DISCRETE SEMICONDUCTOR DEVICES AND INTEGRATED CIRCUITS - PART 5-2: OPTOELECTRONIC DEVICES - ESSENTIAL RATINGS AND CHARACTERISTICS |
| EN 61558-2-16:2009/A1:2013 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS (IEC 61558-2-16:2009/A1:2013) |
| ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
| IEC 60384-14:2013+AMD1:2016 CSV | Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains |
| ISO 8434-1:2007 | Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors |
| IEC 60191-1:2007 | Mechanical standardization of semiconductor devices - Part 1: General rules for the preparation of outline drawings of discrete devices |
| DIN EN 298:2012-11 | Automatic burner control systems for burners and appliances burning gaseous or liquid fuels |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| EN 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN 746-2:2010 | Industrial thermoprocessing equipment - Part 2: Safety requirements for combustion and fuel handling systems |
| EN 10216-5:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes |
| ISO 7637-3:2016 | Road vehicles — Electrical disturbances from conduction and coupling — Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines |
| EN 10213:2007+A1:2016 | Steel castings for pressure purposes |
| EN ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys |
| ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
| EN 13906-1:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs |
| EN 61508-7:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures |
| EN 12067-2:2004 | Gas/air ratio controls for gas burners and gas burning appliances - Part 2: Electronic types |
| ISO 23551-8:2016 | Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 8: Multifunctional controls |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) |
| ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables |
| EN ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:2009) |
| ISO 23551-5:2014 | Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 5: Manual gas valves |
| EN 1643:2014 | Safety and control devices for gas burners and gas burning appliances - Valve proving systems for automatic shut-off valves |
| ISO 23529:2016 | Rubber General procedures for preparing and conditioning test pieces for physical test methods |
| DIN EN 16340:2014-10 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - COMBUSTION PRODUCT SENSING DEVICES |
| ASTM F 593 : 2017 : REDLINE | Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
| ISO 14732:2013 | Welding personnel Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials |
| EN 485-2:2016 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties |
| ISO 23551-10:2016 | Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 10: Vent valves |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| EN 10028-6:2017 | Flat products made of steels for pressure purposes - Part 6: Weldable fine grain steels, quenched and tempered |
| EN 60127-1:2006/A2:2015 | MINIATURE FUSES - PART 1: DEFINITIONS FOR MINIATURE FUSES AND GENERAL REQUIREMENTS FOR MINIATURE FUSE-LINKS |
| ISO 1083:2004 | Spheroidal graphite cast irons - Classification |
| IEC 60050-441:1984 | International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses |
| ASTM A 395/A395M : 1999 | Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| ISO 7637-2:2011 | Road vehicles Electrical disturbances from conduction and coupling Part 2: Electrical transient conduction along supply lines only |
| EN 10111:2008 | Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions |
| ISO 23551-4:2005 | Safety and control devices for gas burners and gas-burning appliances Particular requirements Part 4: Valve-proving systems for automatic shut-off valves |
| EN 10087:1998 | Free-cutting steels - Technical delivery conditions for semi-finished products, hot-rolled bars and rods |
| ASTM A 516/A516M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
| IEC 61558-2-16:2009+AMD1:2013 CSV | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units |
| ISO 7005-3:1988 | Metallic flanges Part 3: Copper alloy and composite flanges |
| EN 586-2:1994 | Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements |
| DIN EN 12067-2:2015-12 (Draft) | GAS/AIR RATIO CONTROLS FOR GAS BURNERS AND GAS BURNING APPLIANCES - PART 2: ELECTRONIC TYPES |
| ASTM B 584 : 2014 : REDLINE | Standard Specification for Copper Alloy Sand Castings for General Applications |
| IEC 60730-2-6:2015 | Automatic electrical controls - Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements |
| ISO 9606-1:2012 | Qualification testing of welders — Fusion welding — Part 1: Steels |
| EN 12516-1:2014 | Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells |
| EN 10346:2015 | Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions |
| EN ISO 9606-4:1999 | Approval testing of welders - Fusion welding - Part 4: Nickel and nickel alloys (ISO 9606-4:1999) |
| IEC 61508-4:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 4: Definitions and abbreviations (see Functional Safety and IEC 61508) |
| EN 88-2:2007 | Pressure regulators and associated safety devices for gas appliances - Part 2: Pressure regulators for inlet pressures above 500 mbar up to and including 5 bar |
| IEC 61810-1:2015 | Electromechanical elementary relays - Part 1: General and safety requirements |
| IEC 61508-3:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 3: Software requirements (see Functional Safety and IEC 61508) |
| IEC 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| EN ISO 14732:2013 | Welding personnel - Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials (ISO 14732:2013) |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| IEC 60747-5-2:1997+AMD1:2002 CSV | Discrete semiconductor devices and integrated circuits - Part 5-2: Optoelectronic devices - Essential ratings and characteristics |
| EN 161:2011+A3:2013 | Automatic shut-off valves for gas burners and gas appliances |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| API 5L : 2012 | LINE PIPE |
| EN 60947-1:2007/A2:2014 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014) |
| EN 10277-3:2008 | Bright steel products - Technical delivery conditions - Part 3: Free-cutting steels |
| EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
| EN ISO 9712:2012 | Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012) |
| EN 10305-1:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 1: Seamless cold drawn tubes |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| ISO 23553-1:2014 | Safety and control devices for oil burners and oil-burning appliances Particular requirements Part 1: Automatic and semi-automatic valves |
| EN 16340:2014 | Safety and control devices for burners and appliances burning gaseous or liquid fuels - Combustion product sensing devices |
| ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure |
| EN 1774:1997 | Zinc and zinc alloys - Alloys for foundry purposes - Ingot and liquid |
| EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| EN 1854:2010 | Pressure sensing devices for gas burners and gas burning appliances |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ASTM A 420/A420M : 2016 : REDLINE | Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress |
| EN 10305-4:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems |
| EN 13906-2:2013 | Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs |
| EN 13445-4 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 4: FABRICATION |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| EN 14459:2015 | Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Methods for classification and assessment |
| EN 61508-2:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems |
| DIN EN 126:2012-06 | MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES |
| EN 10272:2016 | Stainless steel bars for pressure purposes |
| ISO/IEC Guide 51:2014 | Safety aspects — Guidelines for their inclusion in standards |
| EN 10028-5:2017 | Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled |
| DIN EN 16304:2013-05 | Automatic vent valves for gas burners and gas burning appliances |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| EN ISO 17637:2016 | Non-destructive testing of welds - Visual testing of fusion-welded joints (ISO 17637:2016) |
| ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| EN 125:2010+A1:2015 | Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices |
| EN 1706:2010 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
| ISO 23552-1:2007 | Safety and control devices for gas and/or oil burners and gas and/or oil appliances — Particular requirements — Part 1: Fuel/air ratio controls, electronic type |
| EN 10222-5:2017 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
| EN 10250-4:1999 | Open die steel forgings for general engineering purposes - Part 4: Stainless steels |
| DIN EN 88-1:2016-06 | Pressure regulators and associated safety devices for gas appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa (includes Amendment A1:2016) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 126:2012 | Multifunctional controls for gas burning appliances |
| ISO 23551-1:2012 | Safety and control devices for gas burners and gas-burning appliances Particular requirements Part 1: Automatic and semi-automatic valves |
| DIN EN 88-2:2008-03 | Pressure regulators and associated safety devices for gas appliances - Part 2: Pressure regulators for inlet pressures above 500 mbar up to and including 5 bar |
| EN ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005) |
| EN 10250-1:1999 | Open die steel forgings for general engineering purposes - Part 1: General requirements |
| IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV | Low-voltage switchgear and controlgear - Part 1: General rules |
| EN ISO 9606-2:2004 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) |
| EN 1559-1:2011 | Founding - Technical conditions of delivery - Part 1: General |
| ISO 23551-2:2006 | Safety and control devices for gas burners and gas-burning appliances Particular requirements Part 2: Pressure regulators |
| EN 334:2005+A1:2009 | Gas pressure regulators for inlet pressures up to 100 bar |
| EN 10250-2:1999 | Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and special steels |
| EN 62061:2005/A2:2015 | SAFETY OF MACHINERY - FUNCTIONAL SAFETY OF SAFETY-RELATED ELECTRICAL, ELECTRONIC AND PROGRAMMABLE ELECTRONIC CONTROL SYSTEMS (IEC 62061:2005/A2:2015) |
| IEC 61643-11:2011 | Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods |
| ASTM A 217/A217M : 2014 : REDLINE | Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service |
| IEC 60730-2-5:2013+AMD1:2017 CSV | Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems |
| ISO 17637:2016 | Non-destructive testing of welds Visual testing of fusion-welded joints |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN 12164:2016 | Copper and copper alloys - Rod for free machining purposes |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| EN 10130:2006 | Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions |
| DIN EN 16678:2016-02 | Safety and control devices for gas burners and gas burning appliances - Automatic shut-off valves for operating pressure of above 500 kPa up to and including 6 300 kPa |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| ISO 23551-6:2014 | Safety and control devices for gas burners and gas-burning appliances Particular requirements Part 6: Thermoelectric flame supervision controls |
| EN 10083-1:2006 | Steels for quenching and tempering - Part 1: General technical delivery conditions |
| EN 16304:2013 | Automatic vent valves for gas burners and gas burning appliances |
| EN 10083-2:2006 | Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| MSS SP 55 : 2011 | QUALITY STANDARD FOR STEEL CASTINGS FOR VALVES, FLANGES, FITTINGS, AND OTHER PIPING COMPONENTS - VISUAL METHOD FOR EVALUATION OF SURFACE IRREGULARITIES |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| EN 754-2:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties |
| IEC 61508-6:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 6: Guidelines on the application of IEC 61508-2 and IEC 61508-3 (see Functional Safety and IEC 61508) |
| EN 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| EN 10297-1:2003 | Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 1: Non-alloy and alloy steel tubes |
| EN 298:2012 | Automatic burner control systems for burners and appliances burning gaseous or liquid fuels |
| EN 10216-1:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| DIN EN 1643:2014-09 | Safety and control devices for gas burners and gas burning appliances - Valve proving systems for automatic shut-off valves |
| IEC 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508) |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test |
| IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
| EN ISO 148-1:2016 | Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016) |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| ASTM A 312/A312M : 2017-03 | SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES |
| EN 1106:2010 | Manually operated taps for gas burning appliances |
| IEC 61508-7:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures (see Functional Safety and IEC 61508) |
| EN ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003) |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| DIN EN 125:2016-01 | Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices (includes Amendment A1:2015) |
| EN 12165:2016 | Copper and copper alloys - Wrought and unwrought forging stock |
| ISO 301:2006 | Zinc alloy ingots intended for castings |
| IEC 61000-4-29:2000 | Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests |
| EN ISO 9606-1:2017 | Qualification testing of welders - Fusion welding - Part 1: Steels (ISO 9606-1:2012 including Cor 1:2012 and Cor 2:2013) |
| EN ISO 23553-1:2014 | Safety and control devices for oil burners and oil-burning appliances - Particular requirements - Part 1: Automatic and semi-automatic valves (ISO 23553-1:2014) |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts |
| EN 10028-4:2017 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| DIN EN 1106:2010-09 | Manually operated taps for gas burning appliances |
| ISO 23551-9:2015 | Safety and control devices for gas burners and gas-burning appliances Particular requirements Part 9: Mechanical gas thermostats |
| IEC 61508-2:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems (see Functional Safety and IEC 61508) |
| EN 1982:2017 | Copper and copper alloys - Ingots and castings |
| EN 88-1:2011+A1:2016 | Pressure regulators and associated safety devices for gas appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 23550:2011 | Safety and control devices for gas burners and gas-burning appliances General requirements |
| IEC 60384-16:2005 | Fixed capacitors for use in electronic equipment - Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors |
| EN 755-2:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties |
| EN 61000-4-29:2000 | Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
| EN ISO 9606-3:1999 | Approval testing of welders - Fusion welding - Part 3: Copper and copper alloys (ISO 9606-3:1999) |
| EN 50159:2010 | Railway applications - Communication, signalling and processing systems - Safety-related communication in transmission systems |
| EN 10255:2004+A1:2007 | Non-Alloy steel tubes suitable for welding and threading - Technical delivery conditions |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| EN 13555:2014 | Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| EN 10222-1:2017 | Steel forgings for pressure purposes - Part 1: General requirements for open die forgings |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| EN 61508-4:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 4: Definitions and abbreviations |
| ISO 9606-3:1999 | Approval testing of welders — Fusion welding — Part 3: Copper and copper alloys |
| EN 60384-16:2005 | Fixed capacitors for use in electronic equipment - Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c. capacitors |
| SAE J 995 : 2012 | MECHANICAL AND MATERIAL REQUIREMENTS FOR STEEL NUTS |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
| EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
| EN 12186:2014 | Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements |
| EN 257:2010 | Mechanical thermostats for gas-burning appliances |
| DIN EN 161:2013-04 | Automatic shut-off valves for gas burners and gas appliances (includes Amendment A3:2013) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.