DIN EN 13524:2003-10
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
HIGHWAY MAINTENANCE MACHINES - SAFETY REQUIREMENTS
Hardcopy , PDF
07-03-2021
English
01-01-2003
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
National Annex NA (informative) - Bibliography
Foreword
0 Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Information for use
7 Marking
8 Verification
Annex A (informative) - Attachment plate for a truck
Annex B (normative) - Stipulations on the design and
testing of mowing and mulching machines
Annex C (informative) - Thrown-object test reports - Machines
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Describes significant hazards identified through a risk assessment pertinent to highway maintenance machines, when they are used as intended and under the conditions foreseen by the manufacturer.
| DocumentType |
Standard
|
| Pages |
25
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| BS EN 13524 : 2003 | Identical |
| UNI EN 13524 : 2014 | Identical |
| NBN EN 13524 : 2003 + A2 2014 | Identical |
| EN 13524:2003+A2:2014 | Identical |
| I.S. EN 13524:2003 | Identical |
| SN EN 13524 : 2003 + A2 2014 | Identical |
| NF EN 13524 : 2003 + A2 2014 | Identical |
| NEN EN 13524 : 2003 + A2 2014 | Identical |
| NS EN 13524 : 2003 + A2 2014 | Identical |
| UNE-EN 13524:2003 | Identical |
| ONORM EN 13524 : 2014 | Identical |
| ISO 1974:2012 | Paper — Determination of tearing resistance — Elmendorf method |
| EN 1501-2:2005+A1:2009 | Refuse collection vehicles and associated lifting devices - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles |
| EN ISO 15667:2000 | Acoustics - Guidelines for noise control by enclosures and cabins (ISO 15667:2000) |
| ISO 730:2009 | Agricultural wheeled tractors — Rear-mounted three-point linkage — Categories 1N, 1, 2N, 2, 3N, 3, 4N and 4 |
| EN 1501-5:2011 | Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 1501-4:2007 | Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 4: Noise test code for refuse collection vehicles |
| ISO 15667:2000 | Acoustics Guidelines for noise control by enclosures and cabins |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| ISO 11001-2:1993 | Agricultural wheeled tractors and implements — Three-point hitch couplers — Part 2: A-frame coupler |
| ISO 2758:2014 | Paper Determination of bursting strength |
| EN 1501-3:2008 | Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 3: Front loaded refuse collection vehicles |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| EN 791:1995+A1:2009 | Drill rigs - Safety |
| EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
| ISO 789-1:1990 | Agricultural tractors Test procedures Part 1: Power tests for power take-off |
| EN 1501-1:2011+A1:2015 | Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles |
| ISO 11001-4:1994 | Agricultural wheeled tractors and implements — Three-point hitch couplers — Part 4: Bar coupler |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN ISO 4414:2010 | Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010) |
| ISO 6405-1:2017 | Earth-moving machinery Symbols for operator controls and other displays Part 1: Common symbols |
| ISO 536:2012 | Paper and board Determination of grammage |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| ISO 11001-3:2009 | Agricultural wheeled tractors and implements Three-point hitch couplers Part 3: Link coupler |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| EN ISO 2867:2011 | Earth-moving machinery - Access systems (ISO 2867:2011) |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| EN 13019:2001+A1:2008 | Machines for road surface cleaning - Safety requirements |
| ISO 11001-1:2016 | Agricultural wheeled tractors — Three-point hitch couplers — Part 1: U-frame coupler |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 2867:2011 | Earth-moving machinery Access systems |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| ISO 6750:2005 | Earth-moving machinery Operator's manual Content and format |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.