DEFSTAN 22-94/1(2007) : 2007

Foreword
1 Scope
2 Warning
3 Normative References
4 Abbreviations
5 Performance Specification
  5.1 Manufacturers' Type Tests
6 Military Standards/Requirements
  6.1 Manufacture
       6.1.1 Quality
       6.1.2 Method
       6.1.3 Construction
              6.1.3.1 General
              6.1.3.2 Type 7 Hose
       6.1.4 Hose Markings
       6.1.5 Dimensions and Tolerances
              6.1.5.1 Length of Hose and Hose Assembly
              6.1.5.2 Bore
              6.1.5.3 Outside Diameter
              6.1.5.4 Concentricity
              6.1.5.5 Weight
  6.2 Identification and Packing
  6.3 Oils and Greases
7 Design Requirements/Guidance
  7.1 Materials
       7.1.1 Lining
       7.1.2 Reinforcement
       7.1.3 Cover and Sleeve
       7.1.4 Couplings and Associated Fittings
       7.1.5 Binding Wire
  7.2 Production Test and Inspection
       7.2.1 Visual Inspection
       7.2.2 Batch Test
       7.2.3 Acceptance Standard
8 Corporate Experience & Knowledge
Annex A Normative References
Annex B Abbreviations
Annex C Testing and Test Report Requirements for Type 1
        Hose - 64 mm Bore for Abeam RAS for use with
        Portable Water
  C.1 Manufacturer's Testing
  C.2 Rubber Properties Material Tests
  C.3 Adhesion Test
  C.4 Crush Test
  C.5 Bend Radius
  C.6 Bend Test
  C.7 Low Temperature Flexibility Test
  C.8 Hydrostatic Tests
  C.9 Proof Pressure and Axial Rotation Test
  C.10 Burst Test
  C.11 Tensile and Elongation Tests
  C.12 Manufacturer's Test Report Requirements
Annex D Tensile and Elongation Test Equipment and Preparation
        for Type 1 Hose - 64 mm Bore Assembly for Abeam RAS
        for use with Portable Water
  D.1 Test Equipment
  D.2 Preparation of Test Equipment
  D.3 Tensile and Elongation Tests
Annex E Testing and Test Report Requirements for Type 2
        Hose - 64 mm Bore for Abeam RAS for use with
        Lubricating Oils, Dieso Fuel and Avcat
  E.1 Manufacturer's Testing
  E.2 Rubber Properties Material Tests
  E.3 Adhesion Test
  E.4 Crush Test
  E.5 Bend Radius
  E.6 Bend Test
  E.7 Low Temperature Flexibility Test
  E.8 Hydrostatic Tests
  E.9 Proof Pressure and Axial Rotation Test
  E.10 Burst Test
  E.11 Tensile and Elongation Tests
  E.12 Manufacturer's Test Report Requirements
Annex F Tensile and Elongation Test Equipment and
        Preparation for Type 2 Hose - 64 mm Bore for RAS
        for use with Lubricating Oils, Dieso Fuel and Avcat
  F.1 Test Equipment
  F.2 Preparation of Test Equipment
  F.3 Tensile and Elongation Test
Annex G Testing and Test Report Requirements for Type 3
        Hose - 153 mm Bore for Abeam RAS for use with
        Dieso Fuel and Avcat
  G.1 Manufacturer's Testing
  G.2 Rubber Properties Materials Tests
  G.3 Adhesion Test
  G.4 Crush Test
  G.5 Bend Radius Test
  G.6 Bend Test
  G.7 Low Temperature Flexibility Test
  G.8 Hydrostatic Tests
  G.9 Proof Pressure and Axial Rotation Test
  G.10 Burst Test
  G.11 Coupling Inspection
  G.12 Tensile and Elongation Tests
  G.13 Manufacturer's Test Report Requirements
Annex H Tensile and Elongation Test, Equipment and
        Preparation for Type 3 Hose - 153 mm Bore for
        Abeam RAS for use with Dieso Fuel and Avcat
  H.1 Test Equipment
  H.2 Preparation of Test Equipment
  H.3 Tensile and Elongation Tests
Annex I Testing and Test Report Requirements for Type 4
        Hose - 153 mm Bore for Astern RAS for use with
        Dieso Fuel (Lay on Deck)
  I.1 Manufacturer's Testing
  I.2 Rubber Properties Material Tests
  I.3 Adhesion Test
  I.4 Crush Test
  I.5 Bend Radius Test
  I.6 Bend Test
  I.7 Low Temperature Flexibility Test
  I.8 Hydrostatic Tests
  I.9 Proof Pressure and Axial Rotation Test
  I.10 Burst Test
  I.11 Coupling Inspection
  I.12 Tensile and Elongation Tests
  I.13 Manufacturer's Test Report Requirements
Annex J Tensile and Elongation Test, Equipment and Preparation
        for Type 4 Hose - 153 mm Bore for Astern RAS for use
        with Dieso Fuel (Lay on Deck)
  J.1 Test Equipment
  J.2 Preparation of Test Equipment
  J.3 Tensile and Elongation Tests
Annex K Testing and Test Report Requirements for Type 5
        Hose - 153 mm Bore Wire Reinforced Hardwall for use
        on the Probe Received and the Outboard Hose in the
        Abeam Rig in RAS for Dieso Fuel and Avcat
  K.1 Manufacturer's Testing
  K.2 Rubber Properties Material Tests
  K.3 Adhesion Test
  K.4 Crush Test
  K.5 Bend Radius Test
  K.6 Bend Test
  K.7 Low Temperature Flexibility Test
  K.8 Hydrostatic Tests
  K.9 Proof Pressure and Axial Rotation Test
  K.10 Burst Test
  K.11 Tensile and Elongation Tests
  K.12 Manufacturer's Test Report Requirements
Annex L Tensile and Elongation Test, Equipment and Preparation
        for Type 5 Hose - 153 mm Bore Wire Reinforced Hardwall
        for use on the Probe Received and the Outboard Hose in
        the Abeam Rig in RAS for Dieso Fuel and Avcat
  L.1 Test Equipment
  L.2 Preparation of Test Equipment
  L.3 Tensile and Elongation Tests
Annex M Testing and Test Report Requirements for Type 6
        Hose - 153 mm Bore Softwall for use on the Probe
        Receiver in RAS for Dieso Fuel and Avcat
  M.1 Manufacturer's Testing
  M.2 Rubber Properties Material Tests
  M.3 Adhesion Test
  M.4 Crush Test
  M.5 Bend Radius Test
  M.6 Bend Test
  M.7 Low Temperature Flexibility Test
  M.8 Hydrostatic Tests
  M.9 Proof Pressure and Axial Rotation Test
  M.10 Burst Test
  M.11 Tensile and Elongation Tests
  M.12 Manufacturer's Test Report Requirements
Annex N Tensile and Elongation Test, Equipment and Preparation
        for Type 6 Hose - 153 mm Bore Softwall for use in the
        Probe Receiver in RAS for Dieso Fuel and Avcat
  N.1 Test Equipment
  N.2 Preparation of Test Equipment
  N.3 Tensile and Elongation Tests
Annex O Testing and Test Report Requirements for Type 7
        Hose - 153 mm Bore Reelable Astern for RAS for
        use with Dieso Fuel
  O.1 Manufacturer's Testing
  O.2 Rubber Properties Material Tests
  O.3 Adhesion Test
  O.4 Crush Test
  O.5 Bend Radius Test
  O.6 Bend Test
  O.7 Low-Temperature Flexibility Test
  O.8 Hydrostatic Tests
  O.9 Proof Pressure and Axial Rotation Test
  O.10 Burst Test
  O.11 Elongation and Neckdown Tests
  O.12 Tensile Pull
  O.13 Test on the Hose Inclusive of the Area of a Splice
  O.14 Coupling Tests
       O.14.1 Tensile Pull
       O.14.2 High Pressure Hold Test
       O.14.3 Proof Test
       O.14.4 Coupling to Coupling Test for Split Clamp
              Assemblies
  O.15 Manufacturer's Test Report Requirements
Annex P Visible Defects in RAS Hoses
  P.1 Introduction
Annex Q Hose Identification Panel
Annex R Bend Test
  R.1 Sample
  R.2 Method
  R.3 Requirement
Annex S Low Temperature Flexibility Test
  S.1 Method
Annex T Method of Measuring the Free Length of a Hose

Specifies the details for the materials, manufacture, testing and packing of 64 mm bore and 153 mm bore reinforced synthetic rubber hoses and hose assemblies.