DEFSTAN 03-5/3(1995) : 1995
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
AUTOCATALYTIC (ELECTROLESS) NICKEL COATING OF METALS
08-12-2004
12-01-2013
CONTENTS
Section One - General
1 Scope
2 WARNING
3 Related Documents
4 Definitions
5 Information to be Supplied to the Processor
6 Process Control
Section Two - Characteristics and Properties
7 Autocatalytic (Electroless) Nickel Coatings
Section Three - Preparation for Coating
8 General
9 Physical Preparation
10 Cleaning
11 Use of Undercoats and Bath Contamination
12 Areas not Required to be Coated
Section Four - Autocatalytic (Electroless) Nickel Coating
13 Processing
14 Reclamation of Worn and Dimensionally
Section Five - Post-plating Heat Treatment
15 General
16 Purpose of Heat Treatment
17 Improvement of Adhesion
18 Minimizing the Risk of Hydrogen Embrittlement of Steel
Items
19 Increasing the Hardness of the Coating
20 Improvement of the Ductility of the Coating
Section Six - Inspection, Sampling and Testing
21 Inspection
22 Provision of Test Samples
23 Testing
Section Seven - Treatment of Items Rejected During Inspection
and Testing
24 Treatment of Rejected Items
Annex A - Metallographic Method for the Determination of
Local Thickness of Autocatalytic (Electroless)
Nickel Coatings
Annex B - Additional Requirements and Information
Annex C - Approximate Conversion of Metric Units to Imperial
Equivalents
Contains the requirements for the deposition of electroless nickel coatings on metal surfaces by the chemical reduction of a nickel salt in aqueous solutions.
DevelopmentNote |
Supersedes DEFSTAN 03-5/2(1987) & DEFSTAN 03-5/1(1971) (07/2003)
|
DocumentType |
Standard
|
PublisherName |
UK Ministry of Defence Standards
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
DEFSTAN 00-970(PT0)/6(2010) : 2010 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/9(2012) : 2012 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/17(2016) : 2016 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/7(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/15(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/11(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 03-4/4(1998) : 1998 | THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF SPECIFIED MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA |
DEFSTAN 03-2/3(1995) : 1995 | CLEANING AND PREPARATION OF METAL SURFACES |
DEFSTAN 00-970(PT0)/8(2011) : 2011 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 03-32(PT4)/3(2002) : 2002 | PRE-TREATMENT AND PAINTING OF VEHICLES, ENGINEER EQUIPMENT AND COMPONENTS - PART 4: SYSTEMS FOR FERROUS METAL, EXCLUDING ARMOUR |
DEFSTAN 00-970(PT0)/10(2013) : 2013 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/16(2015) : 2015 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
DEFSTAN 00-970(PT0)/5(2007) : 2007 | DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS |
BS 871:1981 | Specification for abrasive papers and cloths |
BS 7479:1991 | Method for salt spray corrosion tests in artificial atmospheres |
DEFSTAN 03-4/4(1998) : 1998 | THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF SPECIFIED MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA |
DEFSTAN 03-21/3(2002) : 2002 | MECHANICAL METHODS FOR THE INDUCEMENT OF RESIDUAL SURFACE COMPRESSIVE STRESSES |
BS 427:1990 | Method for Vickers hardness test and for verification of Vickers hardness testing machines |
DEFSTAN 03-2/3(1995) : 1995 | CLEANING AND PREPARATION OF METAL SURFACES |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.