Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

DEFSTAN 02-304(PT1)/2(2002) : 2002

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

SHAFTING SYSTEMS AND PROPULSORS - PART 1: DESIGN REQUIREMENTS FOR MAIN PROPULSION SHAFTING

Superseded date

08-07-2015

Published date

12-01-2013

Sorry this product is not available in your region.

TITLE PAGE
SCOPE
FOREWORD
Sponsorship
Conditions of Release
Categories of NES
Related Documents
Health and Safety
Additional Information
CONTENTS
SECTION 1 - PERFORMANCE SPECIFICATION
            1.1 Basic Requirements
            1.2 Environmental Conditions
SECTION 2 - NATIONAL/INTERNATIONAL REGULATIONS
            2.1 Health and Safety
SECTION 3 - MILITARY STANDARDS/REQUIREMENTS
            3.1 Drawings
            3.2 Materials
            3.3 Manufacture
            3.4 Balancing
            3.5 Installation
            3.6 Preservation and Storage
SECTION 4 - DESIGN REQUIREMENTS/GUIDANCE
            4.1 Nomenclature
            4.2 Dimensions of Shafting
            4.3 Bearing Span
            4.4 Shaft Whirl
            4.5 Vibration
            4.6 Bending Stresses
            4.7 Tapers
            4.8 Shaft Threads
            4.9 Propeller Nuts
            4.10 Keys and Keyways
            4.11 Couplings
            4.12 Shaft Sleeves
            4.13 Shaft Alignment
            4.14 Shaft Withdrawal
SECTION 5 - CORPORATE KNOWLEDGE AND EXPERIENCE
ANNEX A - RELATED DOCUMENTS
ANNEX B - ABBREVIATIONS AND DEFINITIONS
ANNEX C -PROCUREMENT CHECK LIST
ALPHABETICAL INDEX

Defines the design requirements for shafting as fitted in HM Surface Ships and Submarines.

DevelopmentNote
Supersedes DEFSTAN 02-304(PT1)/1(2000) (01/2003)
DocumentType
Standard
PublisherName
UK Ministry of Defence Standards
Status
Superseded
SupersededBy
Supersedes

DEFSTAN 02-304(PT4)/2(2002) : 2002 SHAFTING SYSTEMS AND PROPULSORS - PART 4: REQUIREMENTS FOR REPAIR OF MAIN PROPULSION SHAFTING
DEFSTAN 02-304(PT2)/2(2002) : 2002 SHAFTING SYSTEMS AND PROPULSORS - PART 2: DESIGN REQUIREMENTS FOR MAIN PROPULSION SHAFTING AUXILIARIES
DEFSTAN 02-305/2(2003) : 2003 REQUIREMENTS FOR GEARING - MAIN PROPULSION
DEFSTAN 02-305/3(2010) : 2010 REQUIREMENTS FOR GEARING - MAIN PROPULSION
DEFSTAN 02-136/2(2004) : 2004 DESIGN, TESTING AND ACCEPTANCE REQUIREMENTS FOR WATERTIGHT INTEGRITY OF SUBMARINES CATEGORY 1
DEFSTAN 02-747(PT3)/2(2011) : 2011 REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE CASTINGS AND INGOTS - PART 3: NICKEL ALUMINIUM BRONZE COMMERCIAL ALLOY INGOTS AND SAND CASTINGS

BS 4500-4:1985 ISO limits and fits Specification for system of cone (taper) fits for cones from <i>C</i>=1:3 to 1:500, lengths from 6 mm to 630 mm and diameters up to 500 mm
BS 1916-2:1953 Limits and fits for engineering Guide to the selection of fits in BS 1916:Part 1
DEFSTAN 02-830(PT1)/2(2002) : 2002 AMD 1 2003 REQUIREMENTS FOR GUNMETAL INGOTS AND CASTINGS - PART 1: GUNMETAL INGOTS AND CLASS 3 GUNMETAL SAND CASTINGS
BS 4500-5:1988 ISO limits and fits Specification for system of cone tolerances for conical workpieces from <i>C</i> = 1:3 to 1:500 and lengths from 6 mm to 630 mm
BS EN 1564:2011 Founding. Ausferritic spheroidal graphite cast irons
DEFSTAN 02-729(PT1)/1(2000) : 2000 REQUIREMENTS FOR NON-DESTRUCTIVE EXAMINATION METHODS - PART 1: RADIOGRAPHIC
DEFSTAN 08-123/1(2000) : 2000 REQUIREMENTS FOR THE DESIGN AND TESTING OF EQUIPMENTS TO MEET ENVIRONMENTAL CONDITIONS - CATEGORY 2
BS 3643-1:1981 ISO metric screw threads Principles and basic data
DEFSTAN 02-745(PT2)/1(2000) : 2000 CLASSIFICATION, INSPECTION REQUIREMENTS AND ACCEPTANCE STANDARDS FOR CASTINGS - PART 2: STEEL CASTINGS
BS ISO 10012-2:1997 Quality assurance for measuring equipment. Guidelines for control of measuring processes
BS EN 20286-1:1993 ISO system of limits and fits ISO system of limits and fits. Bases of tolerances, deviations and fits
BS EN 1563:2011 Founding. Spheroidal graphite cast irons
BS MA 74-2:1981 Tapers and other outboard details of propeller shafts Specification for shafts of diameter greater than 160 mm up to 1000 mm
DEFSTAN 02-729(PT2)/1(2000) : 2000 REQUIREMENTS FOR NON-DESTRUCTIVE EXAMINATION METHODS - PART 2: MAGNETIC PARTICLE
BS 4500-1:1969 ISO limits and fits General, tolerances and deviations
DEFSTAN 02-863/1(2000) : 2000 REQUIREMENTS FOR THE CLASSIFICATION, DIMENSIONS, TOLERANCES AND GENERAL STANDARDS OF ACCEPTANCE FOR COPPER AND NICKEL ALLOY CASTINGS
DEFSTAN 02-833(PT1)/1(2000) : 2000 REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE - PART 1: SHEET, STRIP AND PLATE
DEFSTAN 02-722/1(2000) : 2000 REQUIREMENTS FOR THE PREPARATION, IDENTIFICATION AND MANAGEMENTS OF DRAWINGS
BS 1134-2:1990 Assessment of surface texture. Guidance and general information
DEFSTAN 02-729(PT4)/1(2000) : 2000 REQUIREMENTS FOR NON-DESTRUCTIVE EXAMINATION METHODS - PART 4: LIQUID PENETRATION
DEFSTAN 91-39/3(2001) : 2001 HYDRAULIC FLUID, PETROLEUM: ANTI-WEAR NATO CODE: H-576 JOINT SERVICE DESIGNATION: OM-33
DEFSTAN 02-304(PT3)/2(2002) : 2002 SHAFTING SYSTEMS AND PROPULSORS - PART 3: MANUFACTURING AND DETAIL DESIGN REQUIREMENTS FOR PROPULSORS
DEFSTAN 02-830(PT2)/2(2002) : 2002 REQUIREMENTS FOR GUNMETAL INGOTS AND CASTINGS - PART 2: CONTINUOUSLY CAST
BS EN 20286-2:1993 ISO system of limits and fits ISO system of limits and fits. Tables of standard tolerance grades and limit deviations for holes and shafts
BS EN 1982:2017 Copper and copper alloys. Ingots and castings
DEFSTAN 02-729(PT5)/1(2000) : 2000 REQUIREMENTS FOR NON-DESTRUCTIVE EXAMINATION METHODS - PART 5: ULTRASONIC
DEFSTAN 02-304(PT2)/2(2002) : 2002 SHAFTING SYSTEMS AND PROPULSORS - PART 2: DESIGN REQUIREMENTS FOR MAIN PROPULSION SHAFTING AUXILIARIES
BS 3076:1989 Specification for nickel and nickel alloys: bar
DEFSTAN 02-833(PT2)/1(2000) : 2000 REQUIREMENTS FOR NICKEL ALUMINIUM BRONZE - PART 2: FORGINGS, FORGING STOCK, RODS AND SECTIONS
DEFSTAN 02-848(PT2)/1(2000) : 2000 REQUIREMENTS FOR CARBON MANGANESE AND LOW ALLOY STEEL FORGINGS - PART 2: LOW ALLOY STEEL FORGINGS CATEGORY 2
DEFSTAN 02-848(PT1)/1(2000) : 2000 REQUIREMENTS FOR CARBON MANGANESE AND LOW ALLOY STEEL FORGINGS - PART 1: CARBON MANGANESE STEEL FORGINGS
BS 1916-3:1963 Limits and fits for engineering Recommendations for tolerances, limits and fits for large diameters
DEFSTAN 02-729(PT3)/1(2000) : 2000 REQUIREMENTS FOR NON-DESTRUCTIVE EXAMINATION METHODS - PART 3: EDDY CURRENT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more