DEFSTAN 00-101(PT3)/2(2008) : 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
DESIGN STANDARDS FOR EXPLOSIVES SAFETY IN MOD SHIPS AND SUBMARINES - PART 3: ELECTRICAL EQUIPMENT AND INSTALLATION
Hardcopy , PDF
28-11-2020
English
01-01-2008
0. INTRODUCTION
1. SCOPE
2. WARNING
3. RELATED DOCUMENTS
4. DEFINITIONS AND ABBREVIATIONS
5. AMENDMENT
6. SPONSORSHIP OF THE REQUIREMENT AND SECURITY
7. STATUTORY LEGISLATION AND MOD REGULATION FOR PLATFORM
EXPLOSIVE SAFETY
8. INTRODUCTION TO PLATFORM EXPLOSIVES SAFETY AND CERTIFICATION
9. DESIGN FOR PLATFORM EXPLOSIVES SAFETY INCORPORATING
THREAT HAZARD ASSESSMENT & LINES OF DEFENCE
APPENDIX 1 - DESIGN REQUIREMENTS FOR ELECTRICAL EQUIPMENT
IN MAGAZINES, WSCs AND DESIGNATED DANGER AREAS
1.1 Description
1.2 Performance Requirements - Categorisation of Magazines
1.3 Performance Requirements - Basic Principles for
Magazine Electrical Equipment
1.4 Performance Requirements - Basic Principles - Zone 2
Magazines
1.5 ACOP - Basic Principles - Zone 2 Magazines
1.6 ACOP - Zone 2 Magazine Electrical Equipment Categories
1.7 Performance Requirement - Assessment of Equipment for
use in Zone 2
1.8 ACOP - Electrical Equipment Enclosures
1.9 ACOP - The Radio Frequency (rf) Environment
1.10 ACOP - Magnetic Environment and Degaussing Cables
1.11 Guidance - Basic Principles for Magazine, WSC & DDA
Electrical Equipment
1.12 Guidance - Basic Principles for Zone 2 Magazine,
WSC & DDA Electrical Equipment
1.13 Guidance on Maximum Surface Temperature
1.14 Guidance on Electrical Equipment Enclosures
1.15 Guidance on Intrinsically Safe Equipment
1.16 Guidance on Mobile Mechanical Handling Equipment (MMHE)
1.17 Guidance on Mechanical Hazards
1.18 Guidance on Safety and Environmental Management Systems
(SEMS)
APPENDIX 2 - DESIGN REQUIREMENTS FOR ELECTRICAL INSTALLATIONS
2.1 Description
2.2 Performance Requirements for General Installation
and Siting
2.3 Performance Requirements for Cabling
2.4 Performance Requirements for Circuit Isolation
2.5 Performance Requirements for Emergency Supplies
2.6 Performance Requirements for Fixed Lighting
2.7 Performance Requirements for Power Output Connectors
2.8 Performance Requirements for Installed Test Equipment
2.9 Performance Requirements for Electrically Controlled
Handling Machinery
2.10 Performance Requirements for Safety-Related Devices
2.11 Performance Requirements for Earthing
2.12 ACOP for Siting of Equipment
2.13 ACOP for Cabling
2.14 ACOP for Circuit Isolation
2.15 ACOP for Emergency Supplies
2.16 ACOP for Luminaries (Fixed Lighting)
2.17 ACOP for Power Output Connectors
2.18 ACOP for Test Equipment
2.19 ACOP for Electrically Controlled Handling Machinery
2.20 ACOP for Safety-Related Devices
2.21 ACOP for Earthing
2.22 Guidance on General Electrical Installation
2.23 Guidance on Siting of Equipment
2.24 Guidance on Cabling
2.25 Guidance on Circuit Isolation
2.26 Guidance on Fixed Lighting
2.27 Guidance on Power Output Connectors
2.28 Guidance on Test Equipment
2.29 Guidance on Electrically Controlled Handling Machinery
APPENDIX 3 - DESIGN REQUIREMENTS FOR ADJACENT COMPARTMENTS
3.1 Description
3.2 Performance Requirements for Electrical Design in
Adjacent Compartments
3.3 Performance Requirements for Electrical Equipment
in Adjacent Compartments
3.4 Performance Requirements for Electrical Installation
in Adjacent Compartments
3.5 Performance Requirements for Smoke/Heat Detection
Equipment in Adjacent Compartments
3.6 ACOP for Special Requirements in Adjacent Compartments
3.7 ACOP for Special Requirements for Installation in
Adjacent Compartments
3.8 ACOP for Smoke and Heat Detection Equipment
3.9 Guidance on Electrical Equipment in Adjacent Compartments
APPENDIX 4 - DESIGN REQUIREMENTS FOR TEMPORARILY INSTALLED EQUIPMENT
4.1 Description
4.2 Performance Requirements for Portable Equipment
4.3 Performance Requirements for Emergency Lighting
4.4 ACOP for Temporarily Installed Equipment
4.5 Guidance on Temporarily Installed Equipment
4.6 Guidance on Compliance for Portable Equipment
APPENDIX 5 - ELECTROMAGNETIC INDUCTION, RADIO FREQUENCY AND
ELECTROSTATIC HAZARDS
5.1 Description
5.2 Performance Requirements for Design to Reduce
Electromagnetic Induction, Radio Frequency and
Electrostatic Hazards
5.3 ACOP for Electromagnetic Induction, Radiation and
Electrostatic Hazards
5.4 Guidance on Electromagnetic Induction, Radiation and
Electrostatic Hazards
APPENDIX 6 - POTENTIALLY HAZARDOUS ENVIRONMENTS OF A SPECIAL
NATURE
6.1 Description
6.2 Performance Requirements for Potentially Hazardous
Environments of a Special Nature
6.3 Performance Requirements for Degaussing Cables
6.4 Performance Requirements for Waveguides
6.5 Performance Requirements for Cranes
6.6 Performance Requirements for Ship to Shore Electrical
Connections
6.7 ACOP for Waveguides
6.8 ACOP for Cranes
6.9 ACOP for Ship to Shore Electrical Connections
6.10 ACOP for Earthing of Weapon Containers
6.11 Guidance on Degaussing Cables
6.12 Guidance on Waveguides
6.13 Guidance on Ship to Shore Connections
APPENDIX 7 - Electrical Requirements for ISO Containers
7.1 Description
7.2 ACOP for Earthing of ISO Containers
7.3 Guidance on Earthing of ISO Containers
ANNEX A - RELATED DOCUMENTS
ANNEX B - ABBREVIATIONS
ANNEX C - DEFINITIONS
Applies to the design, construction and ship fitting of all MOD Ships built to MOD or Classification Society constructional standards and operated by the Royal Navy, Army, Royal Air Force, RFA or Marine Services.
DevelopmentNote |
Supersedes DEFSTAN 00-101(PT3)/1(2005). (08/2008) This standard is obsolescent because it is no longer required for procurement of new equipment but is retained for maintenance purposes in support of existing in-service equipment. (09/2017)
|
DocumentType |
Standard
|
Pages |
71
|
PublisherName |
UK Ministry of Defence Standards
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
DEFSTAN 08-107/3(2013) : 2013 | GENERAL REQUIREMENTS FOR THE DESIGN OF ELECTROTECHNICAL AND NAVAL WEAPON EQUIPMENT |
DEFSTAN 02-603/2(2001) : INTERIM | REQUIREMENTS FOR THE POLICY, DESIGN AND INSTALLATION OF FIRE DETECTION SYSTEMS IN SHIPS |
IEC 60079-1:2014 RLV | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
IEC 60079-10:2002 | Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas |
DEFSTAN 02-529(PT2)/1(2000) : 2000 | NUCLEAR HARDENING GUIDE - PART 2: ELECTRICAL INSTALLATION IN SURFACE SHIPS |
AOP 39 : 2010 | GUIDANCE ON THE ASSESSMENT AND DEVELOPMENT OF INSENSITIVE MUNITIONS (IM) |
NES 532 : ISSUE 2 | GUIDE TO THE DESIGN OF ELECTRICAL SUPPLY AND DISTRIBUTION SYSTEMS IN SURFACE SHIPS |
DEFSTAN 08-108(PT1)/1(2000) : 2000 | NUCLEAR HARDENING GUIDE - CATEGORY 1 - PART 1: HARDENING AGAINST NUCLEAR EMP AND INR |
DEFSTAN 59-411(PT5)/1(2007) : 2007 | ELECTROMAGNETIC COMPATIBILITY - PART 5: CODE OF PRACTICE FOR TRI-SERVICE DESIGN AND INSTALLATION |
DEFSTAN 02-113/1(2005) : 2005 | REQUIREMENT FOR MECHANICAL HANDLING |
BS EN 50021:1999 | Electrical apparatus for potentially explosive atmospheres. Type of prot ection \'n\' |
BS EN 61386-1:2008 | Conduit systems for cable management General requirements |
IEC TR 60079-20:1996 | Electrical apparatus for explosive gas atmospheres - Part 20: Data for flammable gases and vapours, relating to the use of electrical apparatus |
DEFSTAN 08-123/1(2000) : 2000 | REQUIREMENTS FOR THE DESIGN AND TESTING OF EQUIPMENTS TO MEET ENVIRONMENTAL CONDITIONS - CATEGORY 2 |
BS EN 50014:1998 | Electrical apparatus for potentially explosive atmospheres. General requirements |
DEFSTAN 08-160/1(2003) : 2003 | REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - CATEGORY 2 |
DEFSTAN 02-602/1(2000) : 2000 | GUIDE TO THE INSTALLATION OF THORN SECURITY AUTOMATIC FIRE DETECTION SYSTEMS CATEGORY N/A |
BS EN 50016:2002 | Electrical apparatus for potentially explosive atmospheres. Pressurized apparatus \'p\' |
DEFSTAN 08-109/2(2001) : 2001 | REQUIREMENTS FOR THE DESIGN OF ELECTRICAL SUPPLY AND DISTRIBUTION SYSTEMS IN SURFACE SHIPS AND SUBMARINES - CATEGORY 1 |
NES 1004 : ISSUE 2 AMD 1 | REQUIREMENTS FOR DESIGN AND TESTING OF EQUIPMENTS TO MEET ENVIRONMENTAL CONDITIONS |
IEC 60079-18:2014 RLV | Explosive atmospheres - Part 18: Equipment protection by encapsulation “m” |
DEFSTAN 59-411(PT4)/1(2007) : 2007 | ELECTROMAGNETIC COMPATIBILITY - PART 4: PLATFORM AND SYSTEM TEST AND TRIALS |
NES 529 PT1 : ISSUE 2 | NUCLEAR HARDENING GUIDE - HARDENING AGAINST NUCLEAR EMP AND INR (RESTRICTED) |
DEFSTAN 08-4(PT1)/2(1992) : 1992 | NUCLEAR WEAPONS EXPLOSIONS EFFECTS AND HARDENING - PART 1: NUCLEAR WEAPONS EXPLOSIONS: RESULTING ENVIRONMENTS |
IEC 60079-5:2015 RLV | Explosive atmospheres - Part 5: Equipment protection by powder filling "q" |
DEFSTAN 08-107/2(2001) : 2001 | GENERAL REQUIREMENTS FOR THE DESIGN OF ELECTROMECHANICAL AND NAVAL WEAPON EQUIPMENT - CATEGORY 2 |
BS EN 60079-14:2014 | Explosive atmospheres Electrical installations design, selection and erection |
IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
IEC 60079-3:1990 | Electrical apparatus for explosive gas atmospheres - Part 3: Spark-test apparatus for intrinsically-safe circuits |
BS EN 50017:1998 | Electrical apparatus for potentially explosive atmospheres. Powder filling \'q\' |
DEFSTAN 08-4(PT3)/2(1992) : 1992 | NUCLEAR WEAPONS EXPLOSIONS EFFECTS AND HARDENING - PART 3: NUCLEAR WEAPONS EXPLOSIONS: SIMULATION OF ENVIRONMENTS |
BS EN 50019:2000 | Electrical apparatus for potentially explosive atmospheres. Increased safety \'e\' |
PD 60079-14:2000 | Guide to application of BS EN 60079-14 |
DEFSTAN 02-607/2(2008) : 2008 | DESIGN OF HIGH VOLTAGE ELECTRICAL POWER SYSTEMS FOR HM SHIPS, SUBMARINES AND THE ROYAL FLEET AUXILIARY |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
DEFSTAN 59-411(PT3)/1(2007) : 2007 | ELECTROMAGNETIC COMPATIBILITY - PART 3: TEST METHODS AND LIMITS FOR EQUIPMENT AND SUB SYSTEMS |
IEC 60079-6:2015 | Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o" |
DEFSTAN 08-124/1(2000) : 2000 | RADIO FREQUENCY ENVIRONMENT AND ACCEPTANCE CRITERIA FOR NAVAL STORES CONTAINING ELECTRO-EXPLOSIVE DEVICES - CATEGORY 1 |
IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
IEC 60079-14:2013 | Explosive atmospheres - Part 14: Electrical installations design, selection and erection |
NES 529 PT2 : ISSUE 1 | NUCLEAR HARDENING GUIDE - ELECTRICAL INSTALLATION IN SURFACE SHIPS |
DEFSTAN 08-147(PT2)/1(2000) : 2000 | REQUIREMENTS FOR DAMAGE CONTROL AND FIRE PROTECTION FOR THE SAFETY OF SURFACE SHIPS AND SUBMARINES - CATEGORY 1 - PART 2: SUBMARINES |
DEFSTAN 08-4(PT2)/2(1992) : 1992 | NUCLEAR WEAPONS EXPLOSIONS EFFECTS AND HARDENING - PART 2: NUCLEAR WEAPONS EXPLOSIONS: EFFECTS ON MATERIEL |
BS EN 50015:1998 | Electrical apparatus for potentially explosive atmospheres. Oil immersion \'o\' |
STANAG 4439 : 2010 | POLICY FOR INTRODUCTION AND ASSESSMENT OF INSENSITIVE MUNITIONS (IM) |
DEFSTAN 59-411(PT2)/1(2007) : 2007 | ELECTROMAGNETIC COMPATIBILITY - PART 2: THE ELECTRIC, MAGNETIC AND ELECTROMAGNETIC ENVIRONMENT |
NES 501 : RESTRICTED | GENERAL REQUIREMENTS FOR THE DESIGN OF ELECTROTECHNICAL AND NAVAL WEAPON EQUIPMENT |
NES 602 : ISSUE 2 | GUIDE TO THE INSTALLATION OF THORN SECURITY AUTOMATIC FIRE DETECTION SYSTEMS |
BS 4568-1:1970 | Specification for steel conduit and fittings with metric threads of ISO form for electrical installations Steel conduit, bends and couplers |
DEFSTAN 59-411(PT1)/1(2007) : 2007 | ELECTROMAGNETIC COMPATIBILITY - PART 1: MANAGEMENT AND PLANNING |
NES 1006 : ISSUE 3 | RADIO FREQUENCY ENVIRONMENT AND ACCEPTANCE CRITERIA FOR NAVAL STORES CONTAINING ELECTRO-EXPLOSIVE DEVICES |
DEFSTAN 08-4(PT4)/2(191993) : 1993 | NUCLEAR WEAPONS EXPLOSIONS EFFECTS AND HARDENING - PART 4: NUCLEAR WEAPONS EXPLOSIONS: HARDENING AND TESTING |
BS EN 50020:2002 | Electrical apparatus for potentially explosive atmospheres. Intrinsic safety \'i\' |
BS EN 50018:2000 | Electrical apparatus for potentially explosive atmospheres. Flameproof enclosure \'d\' |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.