CSA Z107.58 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
NOISE EMISSION DECLARATIONS FOR MACHINERY
Hardcopy , PDF
25-11-2020
English
01-01-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Preface
1 Scope
2 Reference publications
3 Definitions and symbols
4 User decision flowcharts
5 Noise emission declarations
6 Verification of noise emission declarations
7 Using noise emission declarations in the design of workplaces
Annex A (informative) - Criteria for choosing basic noise
emission standards
Annex B (informative) - Sample measurement case
history - Pump manufacturer
Annex C (informative) - Typical industrial sound level
requirements and specifications
Annex D (informative) - Sample noise emission declaration
Annex E (informative) - European Union directives -
Selected excerpts
Annex F (informative) - Contact information for reference
publications
Annex G (informative) - Bibliography
Pertains to provide: a) guidance on the steps required to provide and verify noise emission declarations for machinery and equipment intended for the workplace; b) guidance in the use of noise emission declarations to purchase quieter machinery and plan noise control; c) requirements consistent with the European Union directives pertaining to machinery (EC 00, EC 06, EC 10, EC 13) and the supporting international and European standards, prepared by the International Organization for Standardization (ISO) and the European Committee for Standardization (CEN); d) information that could also be applicable to the use of similar US national standards of the American National Standards Institute (ANSI); and e) additional requirements reflecting Canadian concerns with respect to noise measurements, employee exposure, and engineering noise control.
| DocumentType |
Standard
|
| Pages |
60
|
| PublisherName |
Canadian Standards Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| CSA Z1002 : 2012 : INC : UPD 2 : 2014 | OCCUPATIONAL HEALTH AND SAFETY - HAZARD IDENTIFICATION AND ELIMINATION AND RISK ASSESSMENT AND CONTROL |
| CAN/CSA-Z1002-12 (R2017) | Occupational health and safety - Hazard identification and elimination and risk assessment and control |
| CSA Z1007 : 2016 | HEARING LOSS PREVENTION PROGRAM (HLPP) MANAGEMENT |
| CSA Z1002 : 2012 : INC : UPD 1 : 2013 | OCCUPATIONAL HEALTH AND SAFETY - HAZARD IDENTIFICATION AND ELIMINATION AND RISK ASSESSMENT AND CONTROL |
| CSA Z432 : 2016 | SAFEGUARDING OF MACHINERY |
| CSA Z1002 : 2012 | OCCUPATIONAL HEALTH AND SAFETY - HAZARD IDENTIFICATION AND ELIMINATION AND RISK ASSESSMENT AND CONTROL |
| EN ISO 11204:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 15664:2001 | Acoustics — Noise control design procedures for open plant |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| EN ISO 3743-2:2009 | Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994) |
| ISO 3743-2:1994 | Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| IEC 60942:2003 | Electroacoustics - Sound calibrators |
| CSA Z94.2 : 2014 | HEARING PROTECTION DEVICES - PERFORMANCE, SELECTION, CARE, AND USE |
| ISO 3747:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering/survey methods for use in situ in a reverberant environment |
| EN ISO 3741:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Precision methods for reverberation test rooms (ISO 3741:2010) |
| ISO 3740:2000 | Acoustics Determination of sound power levels of noise sources Guidelines for the use of basic standards |
| ISO 9613-2:1996 | Acoustics — Attenuation of sound during propagation outdoors — Part 2: General method of calculation |
| ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
| EN ISO 11200:2014 | Acoustics - Noise emitted by machinery and equipment - Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions (ISO 11200:2014) |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| EN ISO 3747:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering/survey methods for use in situ in a reverberant environment (ISO 3747:2010) |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| VDI 3760:1996-02 | Computation and measurement of sound propagation in workrooms |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| ISO 6926:2016 | Acoustics Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels |
| ISO 9614-3:2002 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 3: Precision method for measurement by scanning |
| EN ISO 3743-1:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010) |
| CSA Z1007 : 2016 | HEARING LOSS PREVENTION PROGRAM (HLPP) MANAGEMENT |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| EN ISO 9614-3:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 3: Precision method for measurement by scanning (ISO 9614-3:2002) |
| ISO 3741:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Precision methods for reverberation test rooms |
| ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
| EN ISO 11205:2009 | Acoustics - Noise emitted by machinery and equipment - Engineering method for the determination of emission sound pressure levels in situ at the work station and at other specified positions using sound intensity (ISO 11205:2003) |
| EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| EN ISO 11203:2009 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995) |
| IEC 60804:2000 | Integrating-averaging sound level meters |
| ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.