CSA NGV 5.1 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
RESIDENTIAL FUELING APPLIANCES
Hardcopy , PDF
25-11-2020
English
01-01-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Preface
1 Scope
2 Reference publications
3 Definitions
4 General construction and assembly
5 Flow rate
6 General design requirements
7 Marking
8 General testing requirements
9 Additional requirements
10 Quality assurance plan
11 Installation
Annex A (normative) - Items unique to Canada
Annex B (informative) - Compressibility factors (Brill-Begs
correlation for the compressibility factor)
Annex C (informative) - Wire color designations
Describes mechanical, physical, and electrical requirements for a newly manufactured appliance that dispenses natural gas for vehicles directly into the vehicle natural gas fuel storage system, referred to as a residential fueling appliance (RFA).
| DevelopmentNote |
Effective in Canada November 1, 2017. (06/2016)
|
| DocumentType |
Standard
|
| Pages |
79
|
| PublisherName |
Canadian Standards Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| NFPA 54 : 2018 | NATIONAL FUEL GAS CODE |
| ANSI Z223.1 : 2018 | NATIONAL FUEL GAS CODE |
| CSA/ANSI NGV 4.1-2018 | Natural gas vehicle (NGV) dispensing systems |
| NFPA 52 : 2016 | VEHICULAR NATURAL GAS FUEL SYSTEMS CODE |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| CSA NGV1 : 2017 | COMPRESSED NATURAL GAS VEHICLE (NGV) FUELING CONNECTION DEVICES |
| SAE J200_201506 | Classification System for Rubber Materials |
| ASME B18.2.1 : 2012 | SQUARE, HEX, HEAVY HEX, AND ASKEW HEAD BOLTS AND HEX, HEAVY HEX, HEX FLANGE, LOBED HEAD, AND LAG SCREWS (INCH SERIES) |
| UL 514A:11ED 2013-02-01 | Metallic Outlet Boxes |
| CSA/ANSI NGV1 : 2017 | COMPRESSED NATURAL GAS VEHICLE (NGV) FUELING CONNECTION DEVICES |
| ANSI/CSA NGV 4.2-2014 (R2019)/CSA 12.52-2014 (R2018) | Hoses for natural gas dispensing systems |
| CSA B51 : 2014 | BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| CSA C22.2 No. 77 : 2014 | MOTORS WITH INHERENT OVERHEATING PROTECTION |
| CSA 6.5 : 2015 | AUTOMATIC VALVES FOR GAS APPLIANCES |
| SAE J 102 : 1992 | SQUARE HEAD SETSCREWS |
| ASME B18.6.4 : 1998 | THREAD FORMING AND THREAD CUTTING TAPPING SCREWS AND METALLIC DRIVE SCREWS, INCH SERIES |
| ASTM D 1149 : 2016-02 | TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT |
| CSA C22.2 No. 0.4 : 2004(R2013) | BONDING OF ELECTRICAL EQUIPMENT |
| CSA C22.2 No. 0.5 : 2016 | THREADED CONDUIT ENTRIES |
| NFPA 79 : 2015 | ELECTRICAL STANDARD FOR INDUSTRIAL MACHINERY |
| CSA C22.2 No. 24 : 2015 | TEMPERATURE-INDICATING AND -REGULATING EQUIPMENT |
| UL 795:8ED 2016-12-02 | Commercial-Industrial Gas Heating Equipment |
| CSA C22.2 No. 139 : 2013 | ELECTRICALLY OPERATED VALVES |
| ASME B40.100 : 2013 | Pressure Gauges and Gauge Attachments (B40.100 - 2013) |
| CSA 12.3 : 2014 | FUEL SYSTEM COMPONENTS FOR COMPRESSED NATURAL GAS POWERED VEHICLES |
| ASME B18.6.2 : 1998 | SLOTTED HEAD CAP SCREWS, SQAURE HEAD SET SCREWS, AND SLOTTED HEADLESS SET SCREWS (INCH SERIES) |
| IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
| SAE J1065_201605 | Nominal Reference Working Pressures for Steel Hydraulic Tubing |
| CSA 12.56 : 1999 | MANUALLY OPERATED VALVES FOR NATURAL GAS DISPENSING SYSTEMS |
| SAE J1739_200901 | Potential Failure Mode and Effects Analysis in Design (Design FMEA), Potential Failure Mode and Effects Analysis in Manufacturing and Assembly Processes (Process FMEA) |
| MIL-STD-882 Revision E:2012 | System Safety |
| NFPA 52 : 2016 | VEHICULAR NATURAL GAS FUEL SYSTEMS CODE |
| ASME B36.10M : 2015 | WELDED AND SEAMLESS WROUGHT STEEL PIPE |
| ASTM D 865 : 2011 | Standard Test Method for Rubber<char: emdash>Deterioration by Heating in Air (Test Tube Enclosure) |
| NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| SAE J526_201611 | Welded Low-Carbon Steel Tubing Suitable for Bending, Flaring, Beading, Forming and Brazing |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| SAE J525_201609 | Welded and Cold Drawn Low-Carbon Steel Tubing Annealed for Bending and Flaring |
| ASTM D 648 : 2016 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position |
| ASTM D 5420 : 2016 : REDLINE | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| CSA C22.2 No. 100 : 2014 | MOTORS AND GENERATORS |
| SAE J1183_201702 | Recommended Guidelines for Fatigue Testing of Elastomeric Materials and Components |
| SAE J524_201607 | Seamless Low-Carbon Steel Tubing Annealed for Bending and Flaring |
| UL 429:7ED 2013-11-06 | Electrically Operated Valves |
| CFR 49(PTS400-599) : 0 | TRANSPORTATION |
| ASME B18.2.2 : 2015 | NUTS FOR GENERAL APPLICATIONS: MACHINE SCREW NUTS, HEX, SQUARE, HEX FLANGE, AND COUPLING NUTS (INCH SERIES) |
| SAE J 105 : 1992 | HEX BOLTS |
| NFPA 54 : 2018 | NATIONAL FUEL GAS CODE |
| C22.2 NO. 236-15 | Heating and cooling equipment (Bi-national standard with UL 1995) |
| ASME PV CODE SET : 2017 | BOILER AND PRESSURE VESSEL CODE - COMPLETE SET |
| ASTM D 1822 : 2013 : REDLINE | Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials |
| ANSI Z223.1 : 2018 | NATIONAL FUEL GAS CODE |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| UL 515:2ED 2015-07-17 | Standard for Electrical Resistance Trace Heating for Commercial Applications |
| SAE J 479 : 1992 | SLOTTED HEADLESS SETSCREWS |
| UL 60079-0:6ED 2013-07 | Explosive Atmospheres - Part 0: Equipment - General Requirements |
| SAE J 478 : A | SLOTTED AND RECESSED HEAD SCREWS |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASME B18.6.3 : 2013 | MACHINE SCREWS, TAPPING SCREWS, AND METALLIC DRIVE SCREWS (INCH SERIES) |
| NFPA 497 : 2017 | CLASSIFICATION OF FLAMMABLE LIQUIDS, GASES, OR VAPORS AND OF HAZARDOUS (CLASSIFIED) LOCATIONS FOR ELECTRICAL INSTALLATIONS IN CHEMICAL PROCESS AREAS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.