CEI CLC/TS 60034-18-42 : 2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ROTATING ELECTRICAL MACHINES - PART 18-42: QUALIFICATION AND ACCEPTANCE TESTS FOR PARTIAL DISCHARGE RESISTANT ELECTRICAL INSULATION SYSTEMS (TYPE 2) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS
Hardcopy , PDF
01-09-2017
English
01-01-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Voltage effects from converter operation
5 Type II insulation systems
6 Stress factors for converter-fed Type II insulation systems
7 Qualification and acceptance tests
8 Qualification of turn insulation
9 Qualification of ground wall insulation systems
10 Qualification of the stress control and corona protection
system
11 Preparation of test objects
12 Qualification test procedures
13 Qualification test pass criteria
14 Acceptance test for Type II insulation systems (Type test)
15 Analysis, reporting and classification
Annex A (informative)
Annex B (informative)
Annex C (informative)
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Specifies criteria for assessing the insulation system of stator/rotor windings of single or polyphase AC machines which are subjected to repetitive impulse voltages, such as pulse width modulation (PWM) converters, and expected to withstand partial discharge activity during service.
| Committee |
CT 2
|
| DevelopmentNote |
Classificazione CEI 2-48. (02/2012) Superseded by CEI EN 60034-18-42 but remains current and will be withdrawn on 14-03-2020. (10/2017)
|
| DocumentType |
Standard
|
| Pages |
38
|
| PublisherName |
Comitato Elettrotecnico Italiano
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| IEC TS 60034-18-42:2008 | Identical |
| CLC/TS 60034-18-42:2011 | Identical |
| IEC 61800-4:2002 | Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV |
| EN 60034-18-1:2010 | Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines |
| IEC TS 61251:2008 | Electrical insulating materials - A.C. voltage endurance evaluation - Introduction |
| IEC 60034-18-32:2010 | Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance |
| IEC 62068-1:2003 | Electrical insulation systems - Electrical stresses produced by repetitive impulses - Part 1: General method of evaluation of electrical endurance |
| EN 62068-1:2003 | Electrical insulation systems - Electrical stresses produced by repetitive impulses - Part 1: General method of evaluation of electrical endurance |
| EN 60216-3:2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 3: INSTRUCTIONS FOR CALCULATING THERMAL ENDURANCE CHARACTERISTICS |
| IEC TS 60034-18-41:2006 | Rotating electrical machines - Part 18-41: Qualification and type tests for Type I electrical insulation systems used in rotating electrical machines fed from voltage converters |
| IEC 60034-18-1:2010 | Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines |
| EN 60034-18-32:2010 | Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance |
| EN 61800-4:2003 | Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV |
| IEC 62539:2007 | Guide for the statistical analysis of electrical insulation breakdown data |
| IEC 60216-3:2006 | Electrical insulating materials - Thermal endurance properties - Part 3: Instructions for calculating thermal endurance characteristics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.