CAN/CSA-ISO/IEC 18000-3:12 (R2016)
Current
The latest, up-to-date edition.
Information technology - Radio frequency identification for item management - Part 3: Parameters for air interface communications at 13,56 MHz (Adopted ISO/IEC 18000-3:2010, third edition, 2010-11-15)
Hardcopy , PDF
English
01-01-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Conformance
3 Normative references
4 Terms and definitions
5 Symbols and abbreviated terms
6 Requirements: Physical layer, collision management
system and protocol values for 13,56 MHz systems
7 Marking of equipment
Annex A (informative) - MODE 1: mandatory and optional
commands required to support the ISO/IEC 15962
data protocol
Annex B (informative) - MODE 2 and MODE 3: Phase Jitter
Modulation
Annex C (normative) - MODE 3: State transition tables
Annex D (normative) - MODE 3: Command Response Tables
Annex E (normative) - MODE 3: Error codes
Annex F (normative) - MODE 3: Slot counter
Annex G (informative) - MODE 3: Example slot-count (Q)
selection algorithm
Annex H (informative) - MODE 3: Example of tag inventory
and access
Annex I (informative) - MODE 3: Calculation of 5-bit and
16-bit cyclic redundancy checks
Annex J (informative) - MODE 3: ASK Method:
Interrogator-to-tag link modulation
Annex K (informative) - MODE 3: Example data flow exchange
Annex L (informative) - MODE 3: Tag Features
Annex M (informative) - Cyclic Redundancy Check (CRC) (16 bit)
Annex N (informative) - Cyclic redundancy check (CRC) mode
2 (32 bit)
Annex O (informative) - Known possible interferences between
the MODES determined in this part of ISO/IEC 18000
Bibliography
Specifies physical layer, collision management system and protocol values for RFID systems for item identification operating at 13,56 MHz in accordance with the requirements of ISO/IEC 18000-1.
| DocumentType |
Standard
|
| ISBN |
978-1-55491-785-3
|
| Pages |
188
|
| ProductNote |
Reconfirmed EN
|
| PublisherName |
Canadian Standards Association
|
| Status |
Current
|
| Supersedes |
Preface Standards development within the Information Technology sector is harmonized with international standards development. Through the CSA Technical Committee on Information Technology (TCIT), Canadians serve as the Canadian Advisory Committee (CAC) on ISO/IEC Joint Technical Committee 1 on Information Technology (ISO/IEC JTC1) for the Standards Council of Canada (SCC), the ISO member body for Canada and sponsor of the Canadian National Committee of the IEC. Also, as a member of the International Telecommunication Union (ITU), Canada participates in the International Telegraph and Telephone Consultative Committee (ITU-T). This Standard supersedes CAN/CSA-ISO/IEC 18000-3-09 (adoption of ISO/IEC 18000-3:2008, second edition, 2008-09-01). At the time of publication, ISO/IEC 18000-3:2010 is available from ISO and IEC in English only. CSA will publish the French version when it becomes available from ISO and IEC. Scope This part of ISO/IEC 18000 provides physical layer, collision management system and protocol values for RFID systems for item identification operating at 13,56 MHz in accordance with the requirements of ISO/IEC 18000-1. This part of ISO/IEC 18000 provides definitions for systems for each MODE determined in Clause 6 below. This part of ISO/IEC 18000 defines three non-interfering MODES. The MODES are not interoperable. The MODES, whilst not interoperable, are non-interfering.
| Standards | Relationship |
| ISO/IEC 18000-3:2010 | Identical |
| ISO/IEC 15962:2013 | Information technology Radio frequency identification (RFID) for item management Data protocol: data encoding rules and logical memory functions |
| ISO/IEC 7816-6:2016 | Identification cards — Integrated circuit cards — Part 6: Interindustry data elements for interchange |
| ISO/IEC TR 18047-3:2011 | Information technology Radio frequency identification device conformance test methods Part 3: Test methods for air interface communications at 13,56 MHz |
| I-ETS 300 440 : 95 COR 1 96 | RADIO EQUIPMENT AND SYSTEMS (RES) - SHORT RANGE DEVICES - TECHNICAL CHARACTERISTICS AND TEST METHODS FOR RADIO EQUIPMENT TO BE USED IN THE 1 GHZ TO 25 GHZ FREQUENCY RANGE |
| ISO/IEC 18000-6:2013 | Information technology — Radio frequency identification for item management — Part 6: Parameters for air interface communications at 860 MHz to 960 MHz General |
| ISO/IEC 15963:2009 | Information technology Radio frequency identification for item management Unique identification for RF tags |
| ISO/IEC 15961:2004 | Information technology Radio frequency identification (RFID) for item management Data protocol: application interface |
| CFR 47(PTS0-19) : OCT 2017 | TELECOMMUNICATION - FEDERAL COMMUNICATIONS COMMISSION |
| ISO/IEC 10373-7:2008 | Identification cards Test methods Part 7: Vicinity cards |
| ISO/IEC 13239:2002 | Information technology Telecommunications and information exchange between systems High-level data link control (HDLC) procedures |
| ISO/IEC TR 18046:2005 | Information technology Automatic identification and data capture techniques Radio frequency identification device performance test methods |
| EN 300 220-2 : 2.4.1 | SHORT RANGE DEVICES (SRD) OPERATING IN THE FREQUENCY RANGE 25 MHZ TO 1 000 MHZ - PART 2: HARMONISED STANDARD FOR ACCESS TO RADIO SPECTRUM FOR NON SPECIFIC RADIO EQUIPMENT |
| EN 300 220-1 : 2.4.1 | SHORT RANGE DEVICES (SRD) OPERATING IN THE FREQUENCY RANGE 25 MHZ TO 1000 MHZ; PART 1: TECHNICAL CHARACTERISTICS AND METHODS OF MEASUREMENT |
| EN 300 330 : 1.2.2 | SHORT RANGE DEVICES (SRD); RADIO EQUIPMENT IN THE FREQUENCY RANGE 9 KHZ TO 25 MHZ AND INDUCTIVE LOOP SYSTEMS IN THE FREQUENCY RANGE 9 KHZ TO 30 MHZ; HARMONISED STANDARD COVERING THE ESSENTIAL REQUIREMENTS OF ARTICLE 3.2 OF DIRECTIVE 2014/53/EU |
| ISO/IEC 18000-1:2008 | Information technology Radio frequency identification for item management Part 1: Reference architecture and definition of parameters to be standardized |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.