BS ISO 8178-1:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Reciprocating internal combustion engines. Exhaust emission measurement Test-bed measurement systems of gaseous and particulate emissions
Hardcopy , PDF
English
29-06-2017
26-06-2020
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 General measurement principles
6 Engine and ambient related measurement equipment
7 Determination of the gaseous components
8 Particulate determination
9 Calibration and verification
Annex A (normative) - Heat calculation (transfer tube)
Annex B (normative) - Determination of system
equivalence
Annex C (informative) - Carbon flow check
Annex D (informative) - Statistical equations
Annex E (informative) - Examples of Partial Flow
Dilution Systems
Annex F (informative) - Examples of exhaust gas
analysis system
Bibliography
Describes the measurement methods for gaseous and particulate exhaust emissions from reciprocating internal combustion (RIC) engines on a test bed, necessary for determining one weighted value for each exhaust gas pollutant.
| Committee |
MCE/14/-/3
|
| DevelopmentNote |
Supersedes BS EN ISO 8178-1 & 02/706744 DC. (09/2009) Supersedes 16/30334062 DC. (07/2017)
|
| DocumentType |
Standard
|
| Pages |
164
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 8178-1:2017 | Identical |
| ISO 5167-3:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 3: Nozzles and Venturi nozzles |
| ISO 5725-1:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions |
| SAE J244_201106 | Measurement of Intake Air or Exhaust Gas Flow of Diesel Engines |
| ISO 8178-5:2015 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 5: Test fuels |
| CFR 40(PTS87-95) : JUL 2017 | PROTECTION OF ENVIRONMENT |
| ISO 7066-2:1988 | Assessment of uncertainty in the calibration and use of flow measurement devices — Part 2: Non-linear calibration relationships |
| ISO 5168:2005 | Measurement of fluid flow — Procedures for the evaluation of uncertainties |
| ISO 2710-1:2000 | Reciprocating internal combustion engines — Vocabulary — Part 1: Terms for engine design and operation |
| ISO 2710-2:1999 | Reciprocating internal combustion engines — Vocabulary — Part 2: Terms for engine maintenance |
| ISO 8178-2:2008 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 2: Measurement of gaseous and particulate exhaust emissions under field conditions |
| ISO 8178-3:1994 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 3: Definitions and methods of measurement of exhaust gas smoke under steady-state conditions |
| ISO 5167-4:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 4: Venturi tubes |
| ISO 16183:2002 | Heavy duty engines — Measurement of gaseous emissions from raw exhaust gas and of particulate emissions using partial flow dilution systems under transient test conditions |
| ISO 5167-2:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 2: Orifice plates |
| ISO 14396:2002 | Reciprocating internal combustion engines — Determination and method for the measurement of engine power — Additional requirements for exhaust emission tests in accordance with ISO 8178 |
| SAE J1151_201109 | Methane Measurement Using Gas Chromatography |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 1: General principles and requirements |
| IMO IB664 : 2013 SUPP 2015 | MARPOL ANNEX VI & NTC 2008 |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| ISO 3046-1:2002 | Reciprocating internal combustion engines — Performance — Part 1: Declarations of power, fuel and lubricating oil consumptions, and test methods — Additional requirements for engines for general use |
| ISO 8178-7:2015 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 7: Engine family determination |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ISO 8178-4:2017 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 4: Steady-state and transient test cycles for different engine applications |
| CFR 40(PTS1000-END) : JUL 2016 | PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY AND DEPARTMENT OF JUSTICE COUNCIL ON ENVIRONMENTAL QUALITY |
| ISO 2534:1998 | Road vehicles — Engine test code — Gross power |
| ISO 9249:2007 | Earth-moving machinery — Engine test code — Net power |
| ISO 8665:2006 | Small craft — Marine propulsion reciprocating internal combustion engines — Power measurements and declarations |
| ISO 1585:1992 | Road vehicles — Engine test code — Net power |
| ISO 3046-3:2006 | Reciprocating internal combustion engines — Performance — Part 3: Test measurements |
| ISO 8178-6:2000 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 6: Report of measuring results and test |
| ISO 15550:2016 | Internal combustion engines — Determination and method for the measurement of engine power — General requirements |
| ISO 8178-8:2015 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 8: Engine group determination |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.