BS ISO 23551-5:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Safety and control devices for gas burners and gas-burning appliances Manual gas valves
Hardcopy , PDF
31-10-2023
English
31-05-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classes of control
5 Test conditions
6 Construction
7 Performance
8 EMC/Electrical requirements
9 Marking, installation and operating instructions
Annex A (informative) - Leak-tightness test -
Volumetric method
Annex B (informative) - Leak-tightness test -
Pressure-loss method
Annex C (normative) - Conversion of pressure
loss into leakage rate
Annex D (normative) - Test for immunity to
power-frequency magnetic fields
Annex E (normative) - Specific regional requirements
in European countries
Annex F (normative) - Specific regional requirements
in Canada and USA
Annex G (normative) - Specific regional requirements
in Japan
Annex AA (informative) - Examples of manual gas
shut-off valves
Bibliography
Defines safety, constructional and performance requirements for manual gas valves intended for use with gas burners and gas-burning appliances, hereafter referred to as 'valves', unless otherwise specified.
| Committee |
GSE/22
|
| DevelopmentNote |
Supersedes 13/30260415 DC. (05/2014)
|
| DocumentType |
Standard
|
| Pages |
44
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This part of ISO23551 specifies safety, constructional and performance requirements for manual gas valves intended for use with gas burners and gas-burning appliances, hereafter referred to as ‘valves’, unless otherwise specified.
This International Standard applies to following types of manual gas valves:
manual gas shut-off valve;
gas burner valve;
appliance connector valve;
“delta C” valve.
This part of ISO23551 applies to valves for gas burners and gas-burning appliances of nominal connection size up to and including DN 100 that can be used and tested independently of these appliances using fuel gases, as natural gas, manufactured gas or liquefied petroleum gas (LPG) at inlet pressures up to and including 500kPa. It is not applicable to corrosive and waste gases.
This International Standard covers type testing only.
| Standards | Relationship |
| ISO 23551-5:2014 | Identical |
| ISO 8655-1:2002 | Piston-operated volumetric apparatus Part 1: Terminology, general requirements and user recommendations |
| ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
| ISO 23553-1:2014 | Safety and control devices for oil burners and oil-burning appliances Particular requirements Part 1: Automatic and semi-automatic valves |
| ASME B16.1 : 2015 | Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| ISO 23552-1:2007 | Safety and control devices for gas and/or oil burners and gas and/or oil appliances — Particular requirements — Part 1: Fuel/air ratio controls, electronic type |
| SAE J 514 : 2012 | HYDRAULIC TUBE FITTINGS |
| SAE J512 : 1997 | AUTOMOTIVE TUBE FITTINGS |
| ISO 23550:2011 | Safety and control devices for gas burners and gas-burning appliances General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.