BS ISO 2285:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Rubber, vulcanized or thermoplastic. Determination of tension set underconstant elongation, and of tension set, elongation and creep underconstant tensile load
Hardcopy , PDF
25-07-2019
English
30-06-2013
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Apparatus
5 Calibration
6 Test pieces
7 Procedure
8 Expression of results
9 Test report
Annex A (normative) - Calibration schedule
Bibliography
Describes a number of methods of determining the dimensional changes in test pieces of vulcanized or thermoplastic rubber during and after tensile loading for relatively short periods under constant elongation or constant loading.
| Committee |
PRI/22
|
| DevelopmentNote |
Supersedes BS 903-A5(1997). (02/2002) Supersedes 00/121201 DC. (05/2005) Supersedes 07/30164737 DC. (08/2007)
|
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This International Standard specifies a number of methods of determining the dimensional changes in test pieces of vulcanized or thermoplastic rubber during and after tensile loading for relatively short periods under constant elongation or constant loading.
The constant-elongation test is intended to measure the ability of rubbers to retain their elastic properties after extension, at a standard laboratory temperature, to a specified strain which is maintained for a specified time at the same or at a specified higher temperature and then released at the test temperature or at the standard laboratory temperature.
The constant-load test specifies a method for the determination of elongation, creep and tension set of rubbers subjected to a constant load at standard laboratory temperature.
The test methods are intended to measure the elastic properties of rubber in the hardness range 20 IRHD to 94 IRHD.
The creep measurement is not recommended for product design or the evaluation of low-creep materials. For these, reference should be made to ISO 8013. No agreement between the results of this test and those of ISO 8013 should be inferred.
NOTE The constant-load test is primarily intended for the measurement of state of cure and the quality control of thin-walled products. An increase in the state of cure or degree of crosslinking is usually reflected in a decrease in set, creep or elongation.
| Standards | Relationship |
| ISO 2285:2013 | Identical |
| 02/123418 DC : DRAFT AUG 2002 | BS 903-3 - PHYSICAL TESTING OF RUBBER - PART 3: ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA |
| 06/30134942 DC : DRAFT FEB 2006 | BS 1970 - HOT WATER BOTTLES MANUFACTURED FROM RUBBER AND PVC - SPECIFICATION |
| BS 903-0:2003 | Physical testing of rubber General |
| BS 903-0:2012 | Physical testing of rubber General |
| BS 1970:2006 | Hot water bottles manufactured from rubber and PVC. Specification |
| BS 903-3:2003 | Physical testing of rubber Acquisition and presentation of comparable single-point data |
| BS 1970:2012 | Hot water bottles manufactured from rubber and PVC. Specification |
| ISO 23529:2016 | Rubber General procedures for preparing and conditioning test pieces for physical test methods |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| ISO 8013:2012 | Rubber, vulcanized Determination of creep in compression or shear |
| ISO 18899:2013 | Rubber — Guide to the calibration of test equipment |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.