BS ISO 12151-6:2009
Current
The latest, up-to-date edition.
Connections for hydraulic fluid power and general use. Hose fittings Hose fittings with ISO 8434-6 60° cone ends
Hardcopy , PDF
English
31-12-2009
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Performance requirements
5 Designation of hose fittings
6 Design
7 Manufacture
8 Assembly instructions
9 Procurement information
10 Marking
11 Identification statement (reference to this part of
ISO 12151)
Bibliography
Describes the general and dimensional requirements for the design and performance of hose fittings made of carbon steel with 60 degree cone ends for hose sizes 5 to 51 inclusive, in accordance with ISO 4397.
Committee |
MCE/18/-/4
|
DevelopmentNote |
Supersedes 00/715332 DC. (12/2009)
|
DocumentType |
Standard
|
Pages |
24
|
PublisherName |
British Standards Institution
|
Status |
Current
|
Supersedes |
This part of ISO 12151 specifies the general and dimensional requirements for the design and performance of hose fittings made of carbon steel with 60° cone ends for hose sizes 5 to 51 inclusive, in accordance with ISO 4397.
These hose fittings (see Figure 1 for a typical example) are for use in hydraulic fluid power systems with hoses that meet the requirements of the respective hose standards and in general applications with suitable hoses.
NOTE 1 Other materials can be supplied as agreed between the manufacturer and user.
NOTE 2 For hose fittings used in hydraulic and pneumatic braking systems on road vehicles (as defined in the scope of ISO/TC 22), see ISO 4038, ISO 4039-1 and ISO 4039-2.
Standards | Relationship |
ISO 12151-6:2009 | Identical |
ISO 4079-1:2001 | Rubber hoses and hose assemblies Textile-reinforced hydraulic types Specification Part 1: Oil-based fluid applications |
ISO 4039-1:1998 | Road vehicles — Pneumatic braking systems — Part 1: Pipes, male fittings and tapped holes with facial sealing surface |
ISO 3949:2009 | Plastics hoses and hose assemblies Textile-reinforced types for hydraulic applications Specification |
ISO 5598:2008 | Fluid power systems and components Vocabulary |
ISO 4759-1:2000 | Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C |
ISO 6605:2017 | Hydraulic fluid power — Test methods for hoses and hose assemblies |
ISO 4397:2011 | Fluid power connectors and associated components — Nominal outside diameters of tubes and nominal hose sizes |
ISO 4039-2:1998 | Road vehicles — Pneumatic braking systems — Part 2: Pipes, male fittings and holes with conical sealing surface |
ISO 4038:1996 | Road vehicles — Hydraulic braking systems — Simple flare pipes, tapped holes, male fittings and hose end fittings |
ISO 1436-1:2001 | Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types Specification Part 1: Oil-based fluid applications |
ISO 19879:2010 | Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections |
ISO 8434-6:2009 | Metallic tube connections for fluid power and general use — Part 6: 60 degree cone connectors with or without O-ring |
ISO 6149-1:2006 | Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal |
ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
ISO 3862-1:2001 | Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types Specification Part 1: Oil-based fluid applications |
ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.