BS ISO 1101:1983
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Technical drawings. Geometrical tolerancing. Tolerancing of form, orientation, location and run-out. Generalities, definitions, symbols, indications on drawings
Hardcopy , PDF
31-10-2007
English
15-07-2000
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1 Scope
2 Normative references
3 Terms and definitions
4 Basic concepts
5 Symbols
6 Tolerance frame
7 Toleranced features
8 Tolerance zones
9 Datums
10 Supplementary indications
11 Theoretically exact dimensions (TED)
12 Restrictive specifications
13 Projected tolerance zone
14 Maximum material requirement
15 Least material requirement
16 Free state condition
17 Interrelationship of geometrical tolerances
18 Definitions of geometrical tolerances
Annexes
A Former practices
B Assessment of geometrical deviations
C Relation to the GPS matrix model
Bibliography
Provides basic information and gives requirements for the geometrical tolerancing of workpieces. It represents the initial basis and defines the fundamentals for geometrical tolerancing.
| Committee |
TPR/1
|
| DevelopmentNote |
Supersedes BS 308-1(1993) and BS 308-2(1985). (10/2002) Supersedes BS 308-3(1990). (03/2003) Supersedes 95/702648 DC. (01/2005) Renumbered and superseded by BS EN ISO 1101. (10/2007)
|
| DocumentType |
Standard
|
| Pages |
32
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 1101:2017 | Identical |
| BS DD16792(2002) : 2002 | TECHNICAL PRODUCT DOCUMENTATION (TPD) - DIGITAL PRODUCT DEFINITION DATA PRACTICES |
| BS 8888:2008 | Technical product specification. Specification |
| BS 8888:2002 | Technical product documentation (TPD). Specification for defining, specifying and graphically representing products |
| PD 8888:2001 | Technical product documentation (TPD). An interim report |
| BS 4311-1:2007 | Gauge blocks manufactured to imperial specification Specification and validation |
| SAEITC TS66-6 | TS66 Draughting and Part Numbering Procedures for Drawings |
| BS 8888:2000 | Technical product documentation (TPD). Specification for defining, specifying and graphically representing products |
| BS 8888:2004 | Technical product specification (TPS). Specification |
| BS 4311(2007) : 2007 | GAUGE BLOCKS MANUFACTURED TO IMPERIAL SPECIFICATION - SPECIFICATION, VALIDATION AND ACCESSORIES |
| BIP 3016 : 2004 | BS 8888(2004) - TECHNICAL PRODUCT SPECIFICATION CD-ROM |
| BS 8888:2006 | Technical product specification (TPS). Specification |
| ISO/TS 12181-2:2003 | Geometrical Product Specifications (GPS) Roundness Part 2: Specification operators |
| ISO/TS 12781-1:2003 | Geometrical Product Specifications (GPS) Flatness Part 1: Vocabulary and parameters of flatness |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) Masterplan |
| ISO 8015:2011 | Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules |
| ISO/TS 17450-2:2002 | Geometrical product specifications (GPS) General concepts Part 2: Basic tenets, specifications, operators and uncertainties |
| ISO 5459:2011 | Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems |
| ISO 2692:2014 | Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO/TS 12780-1:2003 | Geometrical Product Specifications (GPS) Straightness Part 1: Vocabulary and parameters of straightness |
| ISO 128-24:2014 | Technical drawings General principles of presentation Part 24: Lines on mechanical engineering drawings |
| ISO 7083:1983 | TECHNICAL DRAWINGS - SYMBOLS FOR GEOMETRICAL TOLERANCING - PROPORTIONS AND DIMENSIONS |
| ISO 3040:2016 | Geometrical product specifications (GPS) Dimensioning and tolerancing Cones |
| ISO/TR 5460:1985 | Technical drawings Geometrical tolerancing Tolerancing of form, orientation, location and run-out Verification principles and methods Guidelines |
| ISO 14660-2:1999 | Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature |
| ISO 3098-2:2000 | Technical product documentation — Lettering — Part 2: Latin alphabet, numerals and marks |
| ISO 10578:1992 | Technical drawings Tolerancing of orientation and location Projected tolerance zone |
| ISO/TS 12180-2:2003 | Geometrical Product Specifications (GPS) Cylindricity Part 2: Specification operators |
| ISO 3098-0:1997 | Technical product documentation Lettering Part 0: General requirements |
| ISO/TS 12781-2:2003 | Geometrical Product Specifications (GPS) Flatness Part 2: Specification operators |
| ISO 14660-1:1999 | Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions |
| ISO/TS 12180-1:2003 | Geometrical Product Specifications (GPS) Cylindricity Part 1: Vocabulary and parameters of cylindrical form |
| ISO 1660:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing |
| ISO 10579:2010 | Geometrical product specifications (GPS) — Dimensioning and tolerancing — Non-rigid parts |
| ISO 5458:1998 | Geometrical Product Specifications (GPS) Geometrical tolerancing Positional tolerancing |
| ISO/TS 12181-1:2003 | Geometrical Product Specifications (GPS) Roundness Part 1: Vocabulary and parameters of roundness |
| ISO/TS 12780-2:2003 | Geometrical Product Specifications (GPS) Straightness Part 2: Specification operators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.