BS EN IEC 62677-3-102:2018
Current
The latest, up-to-date edition.
Heat-shrinkable low and medium voltage moulded shapes Specification for individual materials. Sheet 102: Heat-shrinkable, polyolefin, anti-tracking moulded shapes for medium voltage applications
Hardcopy , PDF
English
24-04-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 Conditions of test for dimensions
6 Requirements
7 Moulded shapes material conformance
Annex A (informative) - Adhesive compatibility guide
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Pertains to heat shrinkable medium voltage moulded shapes in a range of configurations suitable for insulation, environmental sealing, mechanical protection, strain relief for power cable terminations, joints and stop ends.
| Committee |
GEL/15/5
|
| DevelopmentNote |
Supersedes 15/30324023 DC. (05/2018)
|
| DocumentType |
Standard
|
| Pages |
16
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
This part of IEC 62677 is applicable to heat shrinkable medium voltage moulded shapes in a range of configurations suitable for insulation, environmental sealing, mechanical protection, strain relief for power cable terminations, joints and stop ends. These moulded shapes have been found suitable for use for temperatures between –40 °C and 100 °C.
The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive compatibility and temperature performance is given in Annex A. The manufacturers/suppliers can be consulted for options.
Materials which conform to this document meet established levels of performance. However, the selection of a material by a user for a specific application will be based on the actual requirements necessary for adequate performance in that application and will not be based on this document alone.
The tests specified are designed to control the quality of the moulded shapes but it is recognized that they are designed to be used in low and medium voltage cable accessories and as such electrical performance will be proven as part of the assembly. Examples of this are described in IEC 60502 (all parts), EN 50393 and HD 629.
| Standards | Relationship |
| IEC 62677-3-102:2018 | Identical |
| EN 62282-6-300:2009 | Identical |
| EN IEC 62677-3-102:2018 | Identical |
| IEC 60684-3-283:2010+AMD1:2013 CSV | Flexible insulating sleeving - Part 3: Specifications for individualtypes of sleeving - Sheet 283: Heat-shrinkable, polyolefin sleeving for bus-bar insulation |
| IEC 62677-2:2017 | Heat shrinkable low and medium voltage moulded shapes - Part 2: Methods of test |
| IEC 62677-1:2017 | Heat shrinkable low and medium voltage moulded shapes - Part 1: General requirements |
| ISO 846:1997 | Plastics Evaluation of the action of microorganisms |
| IEC 60757:1983 | Code for designation of colours |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60684-3-280:2010+AMD1:2013 CSV | Flexible insulating sleeving - Part 3: Specifications for individualtypes of sleeving - Sheet 280: Heat-shrinkable, polyolefin sleeving,anti-tracking |
| EN 50393:2015 | Test methods and requirements for accessories for use on distribution cables of rated voltage 0,6/1,0 (1,2) kV |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.